Sceptre D54 Manual de usuario

Important Safety Instructions

Please read the following instructions carefully. This manual should be retained

for future use.

1. To clean the monitor screen, first, make sure the monitor is in the power off

mode. Second, stand away from the monitor and spray cleaning solution onto

a rag. Without applying excess pressure, clean the screen with the slightly

dampened rag. Do not spray liquid cleaners directly onto the unit.

2. Do not place your monitor near a window. Exposing the monitor to rain, wa-

ter, moisture or sunlight can severely damage it.

3. Do not obstruct the ventilation openings. They are necessary for air circula-

tion and for protecting the device against overheating.

4. Do not lay anything on top of the monitor-to-PC signal cord. Furthermore,

make sure the cord is placed in an area where it will not be stepped on.

5. Do not remove the cover or attempt to service this unit by yourself. You may

void your warranty. Servicing of any nature should be performed only by an

authorized technician.

6. Safe storage of the monitor is in a range of minus 20 to plus 60 degrees Cel-

sius. Storing your monitor outside this range could result in permanent

damage.

7. If any of the following occur, immediately unplug your monitor and call an

authorized technician.

♦=The power monitor-to-PC signal cord is frayed or damaged.

♦=Liquid has been spilled into the monitor, or it has been exposed to rain.

♦=The monitor has been dropped or the case has been damaged.

♦=The device shows obvious signs of a defect.

8. Please turn to your service center for all questions concerning service and

repair to guarantee the devices performance reliability.

— ii —

FEDERAL COMMUNICATIONS COMMISSION

(FCC STATEMENT)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy, and,

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

•=Reorient or relocate the receiving antenna;

•=Increase the separation between the equipment and receiver;

•=Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected;

•=Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the manufacturers may

void the user’s authority to operate this equipment.

A shielded-type power cord is required in order to meet the FCC emission

limits and also to prevent interference to nearby radio and television

reception. It is essential that only the supplied power cord be used.

Use only shielded cables to connect I/O devices to this equipment.

Canadian DOC Notice

For Class B Computing Devices

This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement

sur le matériel brouilleur du Canada.

— iii —

Table of Contents

Chapter 1_________________________________________1

Introduction____________________________________________ 1

Unpacking __________________________________________ 1

Getting Started _________________________________________ 2

Connecting the Monitor and Stand________________________ 2

Choosing a Workstation________________________________ 3

The AC Connection ___________________________________ 4

The Signal Cable Connection____________________________ 4

Monitor Adjustments __________________________________ 5

Chapter 2_________________________________________6

The On-Screen Display (OSD)_____________________________ 8

The Display Controls__________________________________ 6

Adjusting the Brightness and Contrast_____________________ 7

OSD Main Menu _____________________________________ 8

Color Setup ________________________________________ 10

OSD Window Status _________________________________ 12

Reset and Degauss ___________________________________ 13

Self-Test Screen_____________________________________ 14

Summary of OSD Icons _______________________________ 15

Appendix A ______________________________________17

Trouble Shooting_______________________________________ 17

— 1 —

CHAPTER 1

Introduction

Congratulations on your purchase of the new high performance 17" Monitor.

Much consideration has gone into the design of the monitor in order to meet your

requirements for full compatibility and versatility as well as quality.

Using state-of-the-art electronics, the monitor can support a resolution of

1280x1024, and the on-screen display allows you to customize the display settings

to suit your individual needs. User display settings will be automatically saved to

memory. In addition, at the touch of a button the user can, at any time, return to the

factory default display settings.

Other ergonomic features include a non-glare screen, tilt and swivel and just two

multi-function display controls that allow you to make all monitor display adjust-

ments.

Unpacking

Please make sure the following items are in the shipping package and found in

good condition:

•=17" Monitor

•=Tilt and swivel stand

•=Power cord

•=Signal cable (attached to monitor)

•=This manual

If any of the above are missing or appear damaged, please contact your dealer

immediately.

Connecting the Monitor and Stand

— 2 —

Getting Started

This chapter covers setting up the monitor and stand in a suitable workplace, and

connecting the power cord and signal cable.

Connecting the Monitor and Stand

♦=Align the stand’s four tabs with the slots in the bottom of the monitor.

♦=Insert the tabs into the slots.

♦=Slide the stand toward the front of the monitor. You will hear the

spring lock click into place

♦=If you need to remove the stand, push the spring lock and slide the

stand away from the front of the monitor.

Figure 1: Monitor and Stand Connection

Chapter 1

— 3 —

Choosing a Workstation

Keep the following in mind when choosing a work place for the Monitor.

♦=Place the monitor on a stable even surface.

♦=Access to an electrical outlet and telephone jack.

♦=Ensure at least three inches clearance at the rear of the monitor to allow

for sufficient airflow.

♦=Position the Monitor a little above eye-level to reduce neck-strain.

♦=Do not place near a window. Exposing the Monitor to direct sunlight

for extended periods may damage the unit.

♦=You may want to use a desk lamp to adjust the ambient lighting for

your viewing comfort.

♦=A viewing filter is recommended to reduce eye stress and fatigue.

Power On/Off Button

Power LED

Figure 2: The Workstation

The AC Connection

— 4 —

The AC Connection

♦=Locate the AC port on the rear of the monitor (refer to Figure 3).

♦=Plug the female end of the AC cord into the AC port.

♦=Plug the male end into the power supply.

Figure 3: Connecting the Power Cord

The Signal Cable Connection

♦=Make sure that the monitor is powered Off. When powered off the

Power LED (see Figure 2) will not be lit.

♦=Locate the VGA port on the rear of the PC. The signal cable has a

standard 15-pin mini D-sub (VGA) connector. If you are having trou-

ble locating the VGA port, please refer to the documentation, which

came with your PC.

♦=Connect the Signal cable to the PC’s VGA port.

Figure 4: Connecting the Signal Cable

Chapter 1

— 5 —

Monitor Adjustments

The monitor is capable of both tilt and swivel adjustments.

Figure 5: Tilt Adjustment

♦=With the tilt feature, the monitor is capable of vertical adjustments of

+50°to -15°.

♦=The swivel feature allows for horizontal monitor adjustments of +45°to

-45°.

Figure 6: Swivel Adjustment

This concludes Chapter 1. The next chapter covers the on-screen display (OSD)

features.

50°

15°

50°

45°

— 6 —

Chapter 2

12 3 4

Contrast (and OSD Increase/Decrease) Control

When the OSD Main Menu is not engaged, turn the Contrast Control (1) to adjust the

display contrast level to accommodate the ambient lighting conditions of your specific

working environment. When the OSD Main Menu is engaged, turning this control

adjusts the display-setting values.

Brightness (and OSD On/Off) Control

When the OSD Main Menu is not engaged turn the Brightness Control (2) to adjust

the display brightness level. Pushing the Brightness Control calls up the OSD Main

Menu. Turn the control to scroll through the menu options.

Power LED

The Power LED (3) informs you of the monitor’s current operating status. The Power

LED will light Green when the monitor is powered On. In Standby mode the LED

lights Amber. When powered Off the LED is not lit.

Power On/Off Button

Push the Power Button (4) to power the monitor On or Off.

Contrast Brightness LED Power Button

ure 7:

unction Controls

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Sceptre

Sceptre

Sceptre C328W-1920R Manual de usuario

Sceptre

Sceptre X20G-NAGA2 Manual de usuario

Sceptre

Sceptre X325BV-FSR Manual de usuario

Sceptre

Sceptre X23 Manual de usuario

Sceptre

Sceptre U750CV-UMRD Manual de usuario

Sceptre

Sceptre X405 Manual de usuario

Sceptre

Sceptre X220T-Naga Manual de usuario

Sceptre

Sceptre E27 Manual de usuario

Sceptre

Sceptre E246 Series Manual de usuario

Sceptre

Sceptre UMC Series Manual de usuario

Sceptre

Sceptre U27 Manual de usuario

Sceptre

Sceptre UMR Series Manual de usuario

Sceptre

Sceptre E195BV-SRR Manual de usuario

Sceptre

Sceptre X20WG-Naga Manual de usuario

Sceptre

Sceptre U558CV-UMR Manual de usuario

Sceptre

Sceptre LCD Monitor Manual de usuario

Sceptre

Sceptre E325BD-FMQR Manual de usuario

Sceptre

Sceptre E405 Manual de usuario

Sceptre

Sceptre U550CV-UM08R Manual de usuario

Sceptre

Sceptre LCD Monitor X9C-NagaV Manual de usuario

Sceptre

Sceptre X20g X20g-NagaIII X20g-NagaIII Manual de usuario

Sceptre

Sceptre X9G-NAGAV Manual de usuario

Sceptre

Sceptre U505 Series Manual de usuario

Sceptre

Sceptre LCD Monitor X9S-NagaV Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación