Sceptre D95 Manual de usuario
i
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained
for future use.
1. To clean the monitor screen, first, make sure the monitor is in the power off
mode. Second, stand away from the monitor and spray cleaning solution onto
a rag. Without applying excess pressure, clean the screen with the slightly
dampened rag. Do not spray liquid cleaners directly onto the unit.
2. Do not place your monitor near a window. Exposing the monitor to rain,
water, moisture or sunlight can severely damage it.
3. The ventilation openings are necessary for air circulation, and should not be
obstructed to protect the device against overheating.
4. Do not lay anything on top of the monitor-to-PC signal cord. Furthermore,
make sure the cord is placed in an area where it will not be stepped on.
5. Do not remove the cover or attempt to service this unit by yourself. You may
void your warranty. Servicing of any nature should be performed only by an
authorized technician.
6. Safe storage of the monitor is in a range of minus 20 to plus 60 degrees
Celsius. Storing your monitor outside this range could result in permanent
damage.
7. If any of the following occur, immediately unplug your monitor and call an
authorized technician.
♦=The power monitor-to-PC signal cord is frayed or damaged.
♦=Liquid has been spilled into the monitor, or it has been exposed to rain.
♦=The monitor has been dropped or the case has been damaged.
♦=The device shows obvious signs of a defect.
8. Please turn to your service center for all questions concerning service and
repair to guarantee the devices performance reliability.
— ii —
FEDERAL COMMUNICATIONS COMMISSION
(FCC STATEMENT)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy, and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•=Reorient or relocate the receiving antenna;
•=Increase the separation between the equipment and receiver;
•=Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected;
•=Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturers may
void the user’s authority to operate this equipment.
A shielded-type power cord is required in order to meet the FCC emission limits
and also to prevent interference to nearby radio and television reception.
It is essential that only the supplied power cord be used.
Use only shielded cables to connect I/O devices to this equipment.
Canadian DOC Notice
For Class B Computing Devices
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
iii
Table of Contents
Chapter 1_________________________________________1
Introduction____________________________________________ 1
Unpacking __________________________________________ 1
Getting Started _________________________________________ 2
Choosing a Workstation________________________________ 2
The AC Connection ___________________________________ 3
The Signal Cable Connection____________________________ 3
Monitor Adjustments __________________________________ 4
Chapter 2_________________________________________5
Adjusting the Brightness and Contrast_____________________ 6
The On-Screen Display (OSD) __________________________ 7
Color Temperature Setup_______________________________ 9
OSD Window Status _________________________________ 11
Reset and Degauss ___________________________________ 12
Self-Test Screen_____________________________________ 13
Summary of OSD Icons _______________________________ 15
Appendix A ______________________________________17
Trouble Shooting_______________________________________ 17
Chapter 1 —
— 1 —
CHAPTER 1
Introduction
Congratulations on your purchase of the new high performance 19" Monitor.
Much consideration has gone into the design of the monitor in order to meet your
requirements for full compatibility and versatility as well as quality.
Using state-of-the-art electronics, the monitor can support a resolution of 1600 x
1200. The on-screen display allows you to customize the display settings to suit
your individual needs, or you can choose from one of the eight pre-set factory
modes. User display settings will be automatically saved to memory. In addition,
at the touch of a button the user can, at any time, return to the factory default
display settings.
Two conveniently placed multi-function display controls that allow you to make all
monitor display adjustments. Other ergonomic features include a non-glare screen
and tilt and swivel adjustment for a comfortable viewing angle.
Unpacking
Please make sure the following items are in the shipping package and found in
good condition:
•=19" Monitor
•=Tilt and swivel stand
•=Power cord
•=Signal cable
•=This manual
If any of the above are missing or appear damaged, please contact your dealer
immediately.
Chapter 1 —
— 2 —
Getting Started
This chapter covers setting up the monitor and stand in a suitable workplace, and
connecting the power cord and signal cable.
Choosing a Workstation
Keep the following in mind when choosing a work place for the Monitor.
♦=The monitor is quite heavy and should be placed on a sturdy countertop
with a stable and even surface.
♦=Access to an electrical outlet.
♦=Ensure at least three inches clearance at the rear of the monitor to allow
for sufficient airflow.
♦=Position the Monitor a little above eye-level to reduce neck-strain.
♦=Do not place near a window. Exposing the Monitor to direct sunlight
for extended periods may damage the unit.
♦=You may want to use a desk lamp to adjust the ambient lighting for
your viewing comfort.
♦=A viewing filter is recommended to reduce eye stress and fatigue.
Power On/Off Button
Power LED
Figure 2: The Workstation
Chapter 1 —
— 3 —
The AC Connection
♦=
♦=Locate the AC port on the rear of the monitor (refer to Figure 3).
♦=Plug the female end of the AC cord into the AC port.
♦=Plug the male end into the power supply.
Figure 3: Connecting the Power Cord
The Signal Cable Connection
♦=Make sure that the monitor is powered Off. When powered off the
Power LED (see Figure 2) will not be lit.
♦=Locate the VGA port on the rear of the PC. The signal cable has a
standard 15-pin mini D-sub (VGA) connector. If you are having
trouble locating the VGA port, please refer to the documentation which
came with your PC.Connect the Signal cable to the PC’s VGA port.
Figure 4: Connecting the Signal Cable
Chapter 1 —
— 4 —
Monitor Adjustments
The monitor is capable of both tilt and swivel adjustments.
Figure 5: Tilt Adjustment
♦=With the tilt feature, the monitor is capable of vertical adjustments of
+5°to -15°.
♦=The swivel feature allows for horizontal monitor adjustments of +45°to
-45°.
Figure 6: Swivel Adjustment
This concludes Chapter 1. The next chapter covers the on-screen display (OSD)
features.
45°
15°
5°
— 5 —
CHAPTER 2
12 3 4
Figure 7: Function Controls
Contrast (and OSD Increase/Decrease) Control
When the OSD Main Menu is not engaged, turn the Contrast Control (1) to adjust
the display contrast level to accommodate the ambient lighting conditions of your
specific working environment.
When the OSD Main Menu is engaged, turning this control adjusts the display-
setting values.
Brightness (and OSD On/Off) Control
When the OSD Main Menu is not engaged turn the Brightness Control (2) to adjust
the display brightness level. Pushing the Brightness Control calls up the OSD Main
Menu. Turn the control to scroll through the menu options.
Power LED
The Power LED (3) informs you of the monitor’s current operating status. The
Power LED will light Green when the monitor is powered On. In Standby mode
the LED lights Amber. When powered Off the LED is not lit.
Power On/Off Button
Push the Power Button (4) to power the monitor On or Off.
Contrast Brightness LED Power Button
Chapter 2 —
— 6 —
Adjusting the Brightness and Contrast
To adjust the contrast and/or brightness, turn the Contrast Control or the
Brightness Control, to call up the following on-screen display:
Brightness
Turn the Brightness Control clockwise to increase the brightness. Turn the control
counterclockwise to decrease the brightness. The brightness level is adjusted from
0% to 100%.
Contrast
Turn the Contrast Control clockwise to increase the contrast. Turn the control
counterclockwise to decrease the contrast. The contrast level is adjusted from 0%
to 100%.
H. Frequency
This field displays the current Horizontal Scan Frequency. . Display only field
V. Frequency
This field displays the current Refresh Rate. Display only field.
Resolution
This field shows the display resolution to which your monitor is set. This is a
display only field.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Monitor de Sceptre
Sceptre
Sceptre X20WG-Naga Manual de usuario
Sceptre
Sceptre LCD Monitor Manual de usuario
Sceptre
Sceptre E27 Manual de usuario
Sceptre
Sceptre U658CV-UMR Manual de usuario
Sceptre
Sceptre X20G-NAGA2 Manual de usuario
Sceptre
Sceptre X405 Manual de usuario
Sceptre
Sceptre U650CV-UMRD Manual de usuario
Sceptre
Sceptre C27 Manual de usuario
Sceptre
Sceptre U27 Manual de usuario
Sceptre
Sceptre C328W-1920R Manual de usuario
Sceptre
Sceptre E325BD-SR Manual de usuario
Sceptre
Sceptre LCD Monitor X9S-NagaV Manual de usuario
Sceptre
Sceptre ST14 Manual de usuario
Sceptre
Sceptre C325B-144KN Manual de usuario
Sceptre
Sceptre C275B-144MN Manual de usuario
Sceptre
Sceptre E246BV-FC Manual de usuario
Sceptre
Sceptre X 7G Naga V X7g-NagaV X7g-NagaV Manual de usuario
Sceptre
Sceptre D40 Manual de usuario
Sceptre
Sceptre E246 Series Manual de usuario
Sceptre
Sceptre X23 Manual de usuario
