SC&T HKM02B-4K Manual de usuario

Button Instruction:

1. ON (Green) 4. MSG (Red)

On –Device ready On –Receive “Remote”Signal

Flashing –System starting up Flashing- System warning

2. LINK (Blue) 5. Display Panel

On–Link connected On Standby –Current Channel

Flashing- Trying to connect/ no input source

3. IR (Red) 6. Menu Button (Blue)

On –Receive IR signal On-Under menu selection

Button

-

+

Menu

Short Press

*Reduce

Number

*Increase

Number

Menu/Cancel

Press together

Enter

HKM02B-4K: Quick Guide

Transmitter (Tx)

Receiver (Rx)

Note: This remote can only control either Tx or Rx.

This Process only sets up the remotes.

You don’t have to point the remote to the devices.

Step 2. Plug and Use

If there are multiple systems on the same network, please make sure

each pair is on a different channel. *Default Channel “0”

Trouble Shooting

HDCP fail: Please use the receiver remote or front panel and enable

Menu 47 “HDCP always On”function on the receiver box.

(Press: Menu -> 47 -> Enter -> 1 -> Enter)

No display: Please force 1080p 60 Hz output on the receiver box by

pressing “Menu -> 40 -> Enter -> 2-> Enter”on the receiver remote

or front panel.

Make sure the Transmitter & Receiver are on the same Channel

Reset to default “Menu -> 333 -> Enter

Point to Point Application

*MSG light will light when receive remote signal

Press &○

7at the same time

Press &○

8at the same time

*Reduce Number: switches channel or function number down

*Increase Number: switches channel or function number up

Step 1. Setup the Remote

1. Enable IGMP V2

2. Setup Jumbo Frame 8K or above

Note: Please find the instruction on the Ethernet switch manual or see the setup example

under the trouble shooting section in the manual

Multi to Multi Application

Step 1. Setup the Remote

Transmitter (Tx)

Receiver (Rx)

Press &○

7at the same time

Press &○

8at the same time

Note: This remote can only control either Tx or Rx

Step 4. Connect Transmitter & Receiver to Gigabit

Mangement Switch

Step 3. Setup the Gigabit Mangement Switch

Step 5. Download the Software

PC Software: http://tiny.cc/n5gc0y

Mobile App: B&W Video Wall Control

Android IOS

Step 2. Setup the Transmitter Box to the Desired Channel

Transmitter:

Press “+”or “-“to the desired channel number and

Press “+”and “-“at the same time to confirm (enter)

# Each Transmitter has to be on a different Channel

Receiver:

Press “+”or “-“to the desired channel number and

Press “+”and “-“at the same time to confirm (enter)

Otros manuales para HKM02B-4K

1

Tabla de contenidos

Manuales populares de Extensor de otras marcas

SY

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Manual de usuario