Saxby Lighting Severus Manual

Instruction leaflet

Severus Outdoor Wall

61219, EL-40107

Commissioning

For your safety, always switch off the power supply before changing lightbulbs, or cleaning.

This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities

exist. Check with your Local Authority or retailer for recycling advice.

Recycling advice

Safety information

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could

damage the finish.

This light source is protected by a shade. This part must be replaced immediately should the shade

become cracked or damaged. This fitting must not be used without the shade in place.

good quality insulation tape.

Diagram C

light is now ready for use.

Fitting/Replacing bulbs

Diagram C.

V3 31/03/2020

WWW.saxbylighting.com Saxby lighting. BH17 7BY

Replace Cracked Shade

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and

satisfactory operation of this product. Please retain these instructions for future reference.

Warning

Specification

Voltage: 240V 50Hz a.c.

Lamp: 1.1W LED Module (SMD), 3000K

IP rating: 65

Layout

Installation

Wiring

Existing fittings must be completely removed before

installation of a new product. Before removing the

existing fitting, carefully note the position of each set

of wires.

account the entry position of the cable and make

sure there is sufficient cable coming out of the wall

to connect to the terminal block. Ensure that the

mounting surface is solid, preferably a brick or block

wall and ensure that there are no other cables or

pipes beneath the surface.

Diagram A. Gently prise off the cover plate to reveal

the 4 retaining screws on the sides of the unit.

Unscrew these to remove the lens housing.

Diagram B. Bring the mains cable through the rubber

grommet in the wall plate and then use the wall plate

as a template and mark the fixings holes, making sure

the wall plate is correctly aligned so that the top of

it is horizontal. Use appropriate fixings to secure the

back plate to the wall.

Wire as detailed below.

ensuring the cables will reach the distance between

the junction box and the light fitting.

cause a hazard. Position cables and outdoor rated

junction boxes (not supplied) away from areas

where they may be at risk from being cut, trapped or

damaged.

cable which is an outdoor grade, rubber sheathed

cable. The mains supply cable must have a

minimum cross sectional area of 1.0mm²

plastic trunking.

This light fitting is Double Insulated and

does not require connection to an Earth

circuit.

Please read these instructions carefully before

commencing any work.

This unit must be fitted by a competent and qualified

electrician.

Install in accordance with IEE Wiring regulations and

To prevent electrocution switch off at mains supply

before installing or maintaining this fitting. Ensure

other persons cannot restore the electrical supply

without your knowledge. If you are in any doubt,

please consult a qualified electrician.

This light fitting should be connected to a fused circuit.

If replacing an existing fitting, make a careful note of

the connections.

This system contains non-replaceable parts and

cannot be serviced. If damage occurs the part should

be scrapped.

Waste electrical products should not be disposed of

with household waste. Please recycle where facilities

exist. Check with your local authority or retailer for

recycling advice.

This product is rated at IP65.

This product is not suitable for location in or near a

marine environment.

This product is not suitable for dimming.

Having correctly identified the wiring from your light

fitting, connect to the approved outdoor rated external

terminal block in the following way:

Check that...

The connections are tight block.

block.

Grommet

Mounting

screws

Incoming

supply

Wall plate

Cover

plate

Lens

housing

Diagram A. Diagram B.

SUPPLY

NEUTRAL

SWITCHED LIVE

LIGHTFITTING

BLUE (N)

BROWN (L)

Este manual sirve para los siguientes modelos

Otros manuales de Luz exterior de Saxby Lighting

Saxby Lighting

Saxby Lighting EL-40094 Manual

Saxby Lighting

Saxby Lighting PYRAMID 1LT WALL Manual de usuario

Saxby Lighting

Saxby Lighting Luminatra Smart RGB Manual de usuario

Saxby Lighting

Saxby Lighting Inova PIR Wall Manual

Saxby Lighting

Saxby Lighting Bosco 1612T35A Manual

Saxby Lighting

Saxby Lighting Bianco LED CCT PIR Manual de usuario

Saxby Lighting

Saxby Lighting Doron Wall Manual

Saxby Lighting

Saxby Lighting Icarus Photocell 2LT Wall Manual de usuario

Saxby Lighting

Saxby Lighting Louvre Outdoor Wall Fitting Manual de usuario

Saxby Lighting

Saxby Lighting Palin Spike Manual

Saxby Lighting

Saxby Lighting 1818PIR Manual

Saxby Lighting

Saxby Lighting Severus Outdoor Wall EL-40103 Manual de usuario

Saxby Lighting

Saxby Lighting POLGU10 Manual de usuario

Saxby Lighting

Saxby Lighting EL-40062 Manual

Saxby Lighting

Saxby Lighting Panther Wall 52016 Manual

Saxby Lighting

Saxby Lighting 13826 Manual de usuario

Saxby Lighting

Saxby Lighting Equinox Bollard Manual

Saxby Lighting

Saxby Lighting Aretz GU10 Recessed Manual de usuario

Saxby Lighting

Saxby Lighting Kios 2 Manual de usuario

Saxby Lighting

Saxby Lighting Midi Wall Manual

Saxby Lighting

Saxby Lighting Picco 95205 Manual de usuario

Saxby Lighting

Saxby Lighting Solaris 76925 Manual

Saxby Lighting

Saxby Lighting OPAZ MV SPIKE Manual de usuario

Saxby Lighting

Saxby Lighting Palin Spike Manual

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

BEGA

BEGA 84 253 Manual

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario