Saxby Lighting Palin Spike Manual

When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of

used bulbs carefully. Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life.

Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.

Check with your retailer re bulb dimming capability before purchasing replacement bulbs.

1. Unscrew the bezel

2. Remove the old bulb by turning anti-clockwise.

3. Insert new bulb.

4. Replace the bezel ensuring that it is tightly secured.

Instruction leaflet

Palin Spike

13797, 13914, 75438

For your safety, always power switch off the supply before cleaning.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities

exist. Check with your Local Authority or retailer for recycling advice.

Recycling advice

Safety information

We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish. Do not

use solvents or abrasive cleaners as these could damage the finish.

For 13797 and 13914, in normal circumstances, stainless steel is very resistant to corrosion. It does however

require maintenance to preserve the high quality appearance. Wash the product with warm soapy water, removing all

surface deposits. Rinse with clear water and with a soft cloth, wipe dry.

In some cases, surface corrosion may arise after installation. This is normally caused by tiny iron particles left

behind after the brushing process when finishing.

Wash and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.

However if the product is subject to extreme environmental conditions such as marine locations, industrial pollution

and acid rain these maintenance procedures should be carried out around four times a year. For severe corrosion,

non-abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash

and dry as detailed above. Then with a soft cloth soaked with a protective oil, wipe all over.

Do not clean the units with a pressure washer.

Fitting/replacing bulbs (Max. 7W LED GU10)

Care and Cleaning

7W LED GU10

V2 08/01/2022

www.saxbylighting.com Saxby Lighting

EU Manufacturer: Brilliant AG,

Brilliantstrasse 1, D-27442 Gnarrenburg

UK Manufacturer: BH17 7BY

This LED's are protected by the glass shade. The shade part must be replaced immediately should it

become cracked or damaged. This fitting must not be used without the glass shade in place.

Replace Cracked Shade

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and

satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This is a Class 1 product and must be earthed.

Please read these instructions carefully before

commencing any work.

This unit must be fitted by a competent and qualified

electrician.

Install in accordance with IEE Wiring regulations and

current Building Regulations.

To prevent electrocution switch off at mains supply

before installing or maintaining this fitting. Ensure

other persons cannot restore the electrical supply

without your knowledge. If you are in any doubt,

please consult a qualified electrician.

This light fitting should be connected to a fused circuit.

If replacing an existing fitting, make a careful note of

the connections.

Always use the correct type and wattage bulb. Never

exceed the wattage stated.

This product is suitable for dimming when used with a

dimmable bulb.

When changing a bulb, always switch off at the mains

and allow the old bulb to cool down before handling.

Dispose of used bulbs carefully and responsibly.

Waste electrical products should not be disposed of

with household waste. Please recycle where facilities

exist. Check with your local authority or retailer for

recycling advice.

This product is rated at IP44.

Please note: entire unit gets hot whilst on for a period

of time.

This light fitting should be connected to a 30mA RCD.

This product may require the use of a outdoor rated

connector block.

If the external flexible cable or cord of this lamp is

damaged the lamp must be returned to the service

agent for repair.

Specification

Voltage: 220-240V~ 50Hz

Lamp: 1 x Max. 7W LED GU10

IP rating: 44

Layout

Wiring

on the location, an approved outdoor rated plug and

socket may be required. Alternatively an approved

outdoor rated external terminal block may be used.

cause a hazard. Position cables and connector block

away from areas where they may be at risk from

being cut, trapped or damaged.

underground must be protected using suitable

conduit or plastic trunking.

spike into, and can support the luminaire. Do not

install in very wet or boggy areas.

Plug Wiring

or in an approved outdoor rated enclosure.

supply.

fitted with a 3 amp fuse. Should the fuse require

replacement, it must be replaced with a fuse rated at

3 amp and approved to BS1362.

coloured in accordance with the following code:

Blue – Neutral

Green / Yellow - Earth

Brown – Live

You have correctly identified the wires

The connections are tight

No loose strands have been left out of the connection

block.

Ensure that all cord grips are tightly secured.

Ensure that all seals are re-fitted correctly.

If not fitting to a plug then the product must be wired to

an approved outdoor rated terminal block.

Having correctly identified the wiring from your existing

light fitting, connect to the approved outdoor rated

external terminal block in the following way:

Wiring

Check that...

Commissioning

spike into, and can support the luminaire. Do not

install in very wet or boggy areas. Push the spike into

the ground.

light is now ready for use.

GREEN / YELLOW

Earth

Neutral

Live

Fuse

3 Amps

Cord Clamp

BLUE

BROWN

SUPPLY

NEUTRAL

EARTH (GREEN/YELLOW)

SWITCHED LIVE

LIGHTFITTING

BLUE (N)

BROWN (L)

GREEN/YELLOW

This product is not suitable for location in or near a

marine environment.

Este manual sirve para los siguientes modelos

Otros manuales de Luz exterior de Saxby Lighting

Saxby Lighting

Saxby Lighting Bianco LED CCT PIR Manual de usuario

Saxby Lighting

Saxby Lighting 13889 Manual de usuario

Saxby Lighting

Saxby Lighting Louvre Outdoor Wall Fitting Manual de usuario

Saxby Lighting

Saxby Lighting Lille Wall Manual

Saxby Lighting

Saxby Lighting Ikon Pro CCT Series Manual

Saxby Lighting

Saxby Lighting Kios 2 Manual de usuario

Saxby Lighting

Saxby Lighting OPAZ MV SPIKE Manual de usuario

Saxby Lighting

Saxby Lighting 73435 Manual

Saxby Lighting

Saxby Lighting Palin Spike Manual

Saxby Lighting

Saxby Lighting Equinox Bollard Manual

Saxby Lighting

Saxby Lighting Bayswater 40045 Manual de usuario

Saxby Lighting

Saxby Lighting Atlantis Post Manual

Saxby Lighting

Saxby Lighting Icarus Photocell 2LT Wall Manual de usuario

Saxby Lighting

Saxby Lighting EL-40094 Manual

Saxby Lighting

Saxby Lighting Severus EL-40105 Manual

Saxby Lighting

Saxby Lighting Ware Outdoor Wall Manual

Saxby Lighting

Saxby Lighting EL-40062 Manual

Saxby Lighting

Saxby Lighting Seina 52104 Manual

Saxby Lighting

Saxby Lighting Severus Manual

Saxby Lighting

Saxby Lighting BLISS 13799 Manual de usuario

Saxby Lighting

Saxby Lighting HOXTON RECESSED Manual de usuario

Saxby Lighting

Saxby Lighting Severus Outdoor Wall EL-40103 Manual de usuario

Saxby Lighting

Saxby Lighting Panther Wall 52016 Manual

Saxby Lighting

Saxby Lighting Hoxton 79195 Manual de usuario

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

BEGA

BEGA 84 253 Manual

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario