Saxby Lighting Atlantis Post Manual

Instruction leaflet

Atlantis Post

70847, 70848

Commissioning

For your safety, always switch off the power supply before changing lightbulbs, or cleaning. Live Voltages may be

present in this unit even when turned of or when completely disconnected. This system contains non-replaceable

parts and cannot be serviced. If damage occurs, the part should be scrapped.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities

exist. Check with your Local Authority or retailer for recycling advice.

Recycling advice

Safety information

Do not use solvents or abrasive cleaners as these could

damage the finish.

In some cases, surface corrosion may arise after

installation. This is normally caused by tiny iron particles

left behind after the brushing process when finishing.

In normal circumstances, stainless steel is very resistant

to corrosion. It does however require maintenance to

preserve the high quality appearance. Wash the product

with warm soapy water, removing all surface deposits.

Rinse with clean water and with a soft cloth, wipe dry.

Then with a soft cloth soaked with a protective oil, wipe

all over.

If the product is subject to extreme environmental

conditions such as marine locations, industrial pollution

and acid rain these maintenance procedures should

be carried out around four times a year. For severe

corrosion, non-abrasive cream cleaners or proprietary

stainless steel cleaners should be used to remove the

corrosion. Wash and dry as detailed above. Then with a

soft cloth soaked with a protective oil, wipe all over.

Glass parts: Remove and wash in warm water or just

use a damp cloth. Do not use abrasive materials as

these will damage the finish.

- Refer to Fig. 1. Fit the product over the fixing bolts,

re-fit the plastic washers (B) and then the dome nuts

(A). Use a suitable spanner to securely tighten the

product to the mounting surface.

- Replace fuse or circuit breaker and switch on. Your

light is now ready for use.

Care & Cleaning

When changing a bulb, always switch off at the mains

and allow the bulb to cool before handling. Dispose of

used bulbs carefully. Use a soft cloth to handle bulbs,

avoid directly touching the bulbs as this will shorten their

life. Do not exceed the wattage stated or use a different

shape bulb from that indicated on the fitting.

Check with your retailer re bulb dimming capability before

purchasing replacement bulbs.

1. Unscrew the bezel

2. Remove the old bulb

by turning anti-clockwise.

3. Insert new bulb.

4 Replace the bezel

ensuring that it is

tightly secured.

Fitting/replacing bulb (Max. 7W LED GU10)

7W LED GU10

70848 70847

The shade must be replaced immediately should the shade become cracked or damaged. This fitting

must not be used without the shade in place.

Replace Cracked Shade

V7 08/04/2022

www.saxbylighting.com Saxby Lighting

EU Manufacturer: Brilliant AG,

Brilliantstrasse 1, D-27442 Gnarrenburg

UK Manufacturer: BH17 7BY

• You have correctly identified the wires.

• The connections are tight.

• No loose strands have been left out of the connection block.

Check that...

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and

satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This light fitting is Class 1 and must be connected to

an Earth circuit

Please read these instructions carefully before

commencing any work.

This unit must be fitted by a competent and qualified

electrician.

Install in accordance with IEE Wiring regulations and

current Building Regulations.

To prevent electrocution switch off at mains supply

before installing or maintaining this fitting. Ensure

other persons cannot restore the electrical supply

without your knowledge. If you are in any doubt,

please consult a qualified electrician.

This light fitting should be connected to a circuit with a

30mA RCD fitted.

If replacing an existing fitting, make a careful note of

the connections.

Always use the correct type and wattage bulb. Using

the incorrect wattage bulb will damage the bulb and

ballast.

When changing a bulb, always switch off at the mains

and allow the old bulb to cool down before handling.

Dispose of used bulbs carefully and responsibly.

Waste electrical products should not be disposed of

with household waste. Please recycle where facilities

exist. Check with your local authority or retailer for

recycling advice.

This product is rated at IP65.

This product is suitable for dimming.

This product is manufactured from marine grade

stainless steel, making it suitable for application in

coastal environments.

Please note: The entire unit gets hot whilst on for a

period of time.

Specification

Voltage: 220-240V~ 50Hz

Lamp: 2 x Max. 7W LED GU10

IP rating: 65

Layout

• Plan the desired layout of this fitting carefully,

ensuring the cables will reach the distance between

the junction box and the light fitting.

• This product is designed for domestic and light

industrial use. It should not be used to support other

objects or used as a replacement for concrete or

metal pillars.

• Avoid locating any cables in positions that would

cause a hazard. Position cables and outdoor rated

junction boxes (not supplied) away from areas

where they may be at risk from being cut, trapped or

damaged.

• We recommend that you use H05RN-F specification

cable (not supplied) which is an outdoor grade,

rubber sheathed cable. The mains supply cable must

have a minimum cross sectional area of 1.0mm².

• This product must be installed into concrete or

paving slab. It must not be installed into soil.

Installation

Wiring

Existing fittings must be completely removed before

installation of a new product. Before removing the

existing fitting, carefully note the position of each set

of wires.

- Refer to Fig. 1. Using the base plate as a template,

mark the fixing holes onto the mounting surface.

- Drill holes to the necessary size and depth - taking

care not to damage any concealed pipes or wiring

below the mounting surface.

- This product comes complete with expanding

bolt type fixings (C) which are suitable for use on

most surfaces, however alternative fixings may be

required.

- Push the fixing bolts into the mounting holes.

• See Fig. 2. Pull spacing strip from inside of tube.

• Unscrew the 4 screws which attach the black box to the spacing strip.

Open the terminal block case and pull out the terminal block.

Wire as detailed below.

• Push terminal block back into the black box and refit the terminal block

cover.

NEUTRAL

EARTH

SWITCHED LIVE

BLUE (N)

BROWN (L)

GREEN/YELLOW

SUPPLY LIGHT FITTING

Fig. 1

Cable wired to product

Terminal block case

Supply cable

Spacing strip

LIVE

wires

NEUTRAL

wires

EARTH

wire

EARTH

wire

Fig. 2

Having correctly identified the wiring from your existing light fitting, pull the wire throught the bottom of the fitting and

connect to the approved IP67 (or higher rated) terminal block inside the product in the following way (recommended

terminal block Ref. 90131/90132)

Este manual sirve para los siguientes modelos

Otros manuales de Luz exterior de Saxby Lighting

Saxby Lighting

Saxby Lighting Triton Spike Manual de usuario

Saxby Lighting

Saxby Lighting Halbury Wall Manual

Saxby Lighting

Saxby Lighting Inova PIR Wall Manual

Saxby Lighting

Saxby Lighting Luminatra Smart RGB Manual de usuario

Saxby Lighting

Saxby Lighting Ikon Pro CCT Series Manual

Saxby Lighting

Saxby Lighting OPAZ MV SPIKE Manual de usuario

Saxby Lighting

Saxby Lighting Zone Bollard Manual de usuario

Saxby Lighting

Saxby Lighting Pati Manual de usuario

Saxby Lighting

Saxby Lighting Picco 95205 Manual de usuario

Saxby Lighting

Saxby Lighting Luminatra Spike 78635 Manual de usuario

Saxby Lighting

Saxby Lighting POLGU10 Manual de usuario

Saxby Lighting

Saxby Lighting Seina Manual de usuario

Saxby Lighting

Saxby Lighting Hoxton 79195 Manual de usuario

Saxby Lighting

Saxby Lighting Severus Outdoor Wall EL-40103 Manual de usuario

Saxby Lighting

Saxby Lighting HOXTON RECESSED Manual de usuario

Saxby Lighting

Saxby Lighting Canillo 67699 Manual de usuario

Saxby Lighting

Saxby Lighting Midi Wall Manual

Saxby Lighting

Saxby Lighting Bianco LED CCT PIR Manual de usuario

Saxby Lighting

Saxby Lighting Bayswater 40045 Manual de usuario

Saxby Lighting

Saxby Lighting 13889 Manual de usuario

Saxby Lighting

Saxby Lighting Equinox Bollard Manual

Saxby Lighting

Saxby Lighting 1818PIR Manual

Saxby Lighting

Saxby Lighting Severus Manual

Saxby Lighting

Saxby Lighting Odyssey ST5009BK Manual de usuario

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

BEGA

BEGA 84 253 Manual

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario