SawStop JSS Manual

Service Procedure SP-JSS-190516-001

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 1 of 10

Tools & Supplies Required for This Procedure:

•#2 Phillips Head Screwdriver

•5mm Allen Wrench

•13mm Wrench

•Blade Wrench

•SawStop Part #JSS-238

Procedure Steps:

(Before starting, please read instructions all the way through to ensure complete understanding)

To ensure safety, disconnect all electrical power to the saw.

1. Tilt the saw to 45 degrees.

Page 2 of 10

2. Lower the blade completely and remove the fence from the saw and set aside.

3. Use a 5mm Allen wrench and a 13mm wrench to loosen and remove the four bolts that attach

the saw to the cart and set aside.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 3 of 10

4. Lift saw off of the cart and place upside down on a soft sturdy surface.

5. There are 15 Phillips head screws around the outer edge of the bottom that attach it to the saw

body. Starting with the screw to the left of the counter spring indentation at the back and

working counter clockwise, remove all 15 and the bottom and set aside.

•NOTE: When the last screw is removed, the bottom will spring upward a bit.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 4 of 10

6. Remove the motor housing bolt that is directly above the motor power cord and set aside.

7. Remove the four bolts that fasten the motor to the elevation carriage assembly.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 5 of 10

8. Turn the motor so it is oriented as shown below. On the left side of the arbor wrench you will

notice a small hole near the end. Finger-tighten the arbor wrench to the motor plate as shown

below with the M5x50mm bolt that was provided with your belt.

9. Re-install one bolt from step 7 through the motor plate into the bottom left motor mounting hole

as shown below. (This will create a pivot point for the motor)

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 6 of 10

10. Put the new belt on both the motor and the arbor pulleys.

11. Pull on the wrench to apply tension to the belt and to align the motor mounting bolt holes.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 7 of 10

12. Reinstall the remaining three motor mounting bolts using a 5mm Allen wrench.

13. Remove the bolt and wrench.

Page 8 of 10

14. Reinstall the motor housing bolt using a Phillips head screwdriver.

15. Tilt the saw back to 90 degrees. Above the motor is the counter balance spring that must be in

the up position leaning against the trunnion.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 9 of 10

16. There is a small groove on the bottom of the indentation that the top of the counter balance

spring must seat in. You’ll want to “hover” the base over the saw and slowly lower it until the

two match up.

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Service Procedure

Steps to Replace Job Site Saw Arbor Belt or Motor

Page 10 of 10

17. Reinstall the 15 screws starting with the one that is left of the indentation.

NOTE: When using a power screw driver, the torque must be set about midrange or you

WILL strip them.

18. Place the saw back on the cart and reinstall the four 5mm bolts and nuts.

Questions?

Contact the SawStop Customer Support Center with any questions or

suggestions:

Call: (503) 582-9934

Email: [email protected]

Otros manuales para JSS

2

Tabla de contenidos

Otros manuales de Sierra de SawStop

SawStop

SawStop T-Glide TGP2-FA Manual de instrucciones

SawStop

SawStop RT-LFT Manual de usuario

SawStop

SawStop MB-CNS-000 Manual de usuario

SawStop

SawStop JSS Manual de usuario

SawStop

SawStop JSS Manual

SawStop

SawStop PCS31230 Manual de usuario

SawStop

SawStop ICS31240-50 Manual de usuario

SawStop

SawStop JOBSITE SAW PRO Manual de usuario

SawStop

SawStop PCS175 Manual de usuario

SawStop

SawStop CB31230 Manual de usuario

SawStop

SawStop CB31230 Manual de usuario

SawStop

SawStop CTS-120A60A Manual de usuario

SawStop

SawStop Jobsite Saw Manual de usuario

SawStop

SawStop CNS-SFA Manual de usuario

SawStop

SawStop JSS-120A60 Manual de usuario

SawStop

SawStop ICS31230 Manual de usuario

SawStop

SawStop TGA-GA48 Manual de usuario

SawStop

SawStop T-Glide Fence System Manual de usuario

SawStop

SawStop T-Glide Manual de usuario

SawStop

SawStop CTS-120A60 Manual de usuario

SawStop

SawStop CTS-015 Manual de usuario

SawStop

SawStop MC-CNS Manual de usuario

SawStop

SawStop 10” Manual de usuario

SawStop

SawStop JSS-MCA Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario