SawStop JSS Manual

Service

Procedure SP-JSS-190522-001

Adjusting JSS Guard Clamp

Page 1 of 2

Tools & Supplies Required for This Procedure:

•4mm Allen wrench

•13mm combination wrench

Background: It sometimes becomes necessary to adjust the alignment of the JSS guard clamp to the

blade, or to adjust the clamping force. The clamp works on the same principles at the other SawStop

saws; the red clamping handle operates a cam that pushes the pressure plate sideways to clamp the

riving knife or splitter into place. This procedure discusses the steps needed to align the splitter with the

saw blade, and to adjust the clamping force.

Procedure Steps:

(Before starting, please read instructions all the way through to ensure complete understanding)

(Table Layout: Sample Text follows)

Guard Clamp Alignment Screws:

Adjusting these screws moves the position of the guard

clamp in and out to align with the saw blade.

Checking alignment:

1. Slide the steel straightedge against the left side of the

blade plate, making sure it runs between the carbide

tips and rides flat against the blade with no air gaps.

2. Ideally, the straightedge should also run flat against

the left side of the riving knife, with no gaps. If so,

you’re done – no alignment is needed.

Service

Procedure SP-JSS-190522-001

Adjusting JSS Guard Clamp

Page 2 of 2

Adjusting alignment:

Adjusting clamping force:

If adjustment is needed:

1. Using a 4mm Allen wrench screwdriver, adjust the

position of the guard clamp left or right to bring it into

alignment with the splitter or riving knife.

2. It’s best to turn each screw the same amount to begin

with to move the whole clamp left or right.

3. If the splitter is at a different angle than the blade,

adjust the screws individually as needed to make the

riving knife parallel to the blade.

1. For adjustment, the clamp needs to be in the up/open

position, so that the cam is not engaged.

2. Push the pressure plate inward; this will expose the

head of the clamping bolt.

3. To adjust clamping force, use a 13mm wrench to turn

the bolt head while it is exposed:

a. To increase force, turn the bolt head clockwise

b. To decrease force, turn the bolt head

counterclockwise

c. To avoid damaging the clamp from

excessive force, adjust in SMALL

increments (1 or at most 2 detents.)

Questions?

Contact the SawStop Customer Support Center with any questions or

suggestions:

Call: (503) 582-9934

Email: [email protected]

Otros manuales para JSS

2

Tabla de contenidos

Otros manuales de Sierra de SawStop

SawStop

SawStop TGA-GA48 Manual de usuario

SawStop

SawStop 10” Manual de usuario

SawStop

SawStop JSS Manual de usuario

SawStop

SawStop Jobsite Saw Manual de usuario

SawStop

SawStop CNS-SFA Manual de usuario

SawStop

SawStop PCS31230 Manual de usuario

SawStop

SawStop T-Glide Fence System Manual de usuario

SawStop

SawStop CB31230 Manual de usuario

SawStop

SawStop JSS-120A60 Manual de usuario

SawStop

SawStop CTS-120A60 Manual de usuario

SawStop

SawStop T-Glide Manual de usuario

SawStop

SawStop CTS-120A60A Manual de usuario

SawStop

SawStop RT-LFT Manual de usuario

SawStop

SawStop CB31230 Manual de usuario

SawStop

SawStop PCS175 Manual de usuario

SawStop

SawStop MB-CNS-000 Manual de usuario

SawStop

SawStop JSS Manual

SawStop

SawStop T-Glide TGP2-FA Manual de instrucciones

SawStop

SawStop JOBSITE SAW PRO Manual de usuario

SawStop

SawStop ICS31230 Manual de usuario

SawStop

SawStop CTS-015 Manual de usuario

SawStop

SawStop MC-CNS Manual de usuario

SawStop

SawStop CNS175 Manual de usuario

SawStop

SawStop ICS31240-50 Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario