Satec PM130 PLUS Manual de instrucciones

BG0441 REV.A9 ENGLISH PM130 PLUS QuickStart www.satec-global.com

PM130 PLUS Quick Start Manual

This Quick Start Manual is a short guide on how to mount, connect, configure and operate the

PM130 PLUS. It is not intended to replace reading the full User Manual –and particularly the

safety precautions. The manual is available on the Product Documentation CD.

Mounting, electrical connection and settings of the PM130 shall be made in

accordance with all applicable laws and/or regulations and be performed by

authorized personnel only.

MOUNTING

Position the PM130 meter in 92×92mm square or 4” round cutout (Figure 1). If two PM130 are

positioned side by side, keep at least 150mm (5.9”) between their centers to allow installation

of add-on modules (140mm/5.5” if only small form modules will be used).

Attach the PM130 unit using washers and nuts. Make sure that the unit is securely attached

into the wall or cabinet fixture.

Figure 1

PM130 PLUS QuickStart www.satec-global.com

CONNECTION

To connect follow these steps (Figure 2 shows a 4W LV installation with conventional CTs):

1. Ensure that all incoming power sources are OFF.

2. Check that you have the appropriate power supply.

3. Connect the Power Supply inputs using 1.5 mm²/14AWG dedicated wires and breaker.

4. Connect to the external CTs by passing the external CTs wires through the meter CT cores.

Observe the arrow that indicates the current direction (Figure 2A). For HACS: connect the

red or white wire to the “-” and orange or black wire to the “+“ terminal.

5. In case of a retrofit application where each external CT ends with two wires (Note 2B):

5.1. Pass one wire through the meter CT core.

5.2. Connect the wire to one of the meter “optional CT wire termination”screws.

5.3. Connect the second wire from the external CT to the termination screw.

6. Connect the measured voltage inputs

7. Connect COM1 –RS-485 communication port

8. To connect the optional module:

8.1. Make sure that the power is turned off

8.2. Remove the module cover

8.3. Attach the module and fasten the screws

8.4. Connect the module I/O or communication (see Figure 2C for DI/O wiring)

9. Turn the power up

10. Make sure the diagnostic led is off

The “optional CT wire termination”

allows connection of the two wires

from the CTs. They have no internal

connection and their use is optional.

Figure 2

Note

Figure 2A

Figure 2C

PM130 PLUS QuickStart www.satec-global.com

OPERATION

The PM130 PLUS is operated using the front panel which consists of a 3-line 7-segment

display, up to 33 LEDs (depending on model) and six keys as shown below:

There are two display modes: readings and menus.

Readings Mode

There are four groups of readings: Common measurement, Min/Max, Harmonics and Energy.

Use MAX/MIN or HIIIIIIor ENERGY to switch between groups, or to scroll within the

group, or simultaneous and to go to the first screen of the current display group.

Menu Mode

Press SELECT to enter menu mode (blinking line indicates the selection). SELECT to change the

selection, ENTER to drill down or ESC to go up. In editing mode use or to change the

value (a number or submenu), ENTER to accept it, or ESC to cancel.

The following chart shows the structure of the menus:





Phase rotation





Real Time Clock





Reset min/max, demands, etc.





Voltage angles





Basic configuration



Same as OPS (Options) menu





Current angles



.

COM2 setup





Relay status (*D)



.

COM2 setup (*E/G/R/P)



.

DI status (*D)





Relay Output (*D)





Counter value in 0.1 hours





Analog Output (*A)



.

Alarm setpoint





Network configuration (*E)





Diagnostics





Setpoints



.

Serial number







Display





Firmware version







Options





GPRS status (*G)

NOTE: Option availability depends on installed add-in module:

*D –Digital I/O; *A –Analog Output; *E –Ethernet; *G –GPRS; *R –RS232/422/485; *P –Profibus.

Diagnostic LED. Off = OK

Load bar graph

(full load according to CT

or in Display Setup)

Displayed

parameters

Calibration LED

(1 pulse/Wh or Varh)

Measurement scale

Communication indication

Main Display

Energy button & indication

(E/EH models) / Enter

Min/Max/Max Demand

button & indication

Harmonics button & indication

(EH model) / Escape

Select

Scroll up / down

 (Status)

Status Indications

 (Options) Read-only

display of the configuration

screens

 (Change) Configuration

PM130 PLUS QuickStart www.satec-global.com

CONFIGURATION

The essential configuration includes:

1. Basic measurement setup

2. Communication setup and testing

3. Resetting the min/max, energy, demands etc.

Additional recommended configuration: set points, TOU and data logging

Note: It may be easier first to configure communication and use PAS software for setup

Basic Measurement Setup

In any display screen, press SELECT x 3 (until  blinks), then press ENTER ( blinks), then

x 2 ()and ENTER to enter the Basic Settings Display.

Parameter

Description

Default

 (see below) 

Network wiring configuration





Transformation ratio of the Potential Transformers



.

Additional PT factor for EHV network





The Primary Rating Of The Current Transformers

(quick access to this parameter: press SELECT, then simultaneous and SELECT)



.(E & EH models)

Duration in minutes of the power demand period calculations

E = External pulse in DI1



.(E & EH models)

The number of blocks to be averaged for sliding window demands



.

Duration in seconds for voltage and current demand





The nominal frequency





Max. Demand Load Current in Amperes. 0 = CT primary current.



Wiring Mode

Setup

3-wire 2-element Delta direct connection using 2 CTs



4-wire 3-element Wye direct connection or 3PTs, and 3 CTs

 or *

3-wire 2-element Open Delta connection using 2 PTs, 2 CTs



4-wire 2½-element Wye connection using 2 PTs, 3 CTs

 or *

3-wire 2½-element Open Delta connection using 2 PTs, 3 CTs



4-wire 3-element Delta direct connection using 3 CTs

 or *

3-wire 2½-element Broken Delta connection using 2 PTs, 3 CTs

 or *

* LN or LL denotes the default use of L-L or L-N voltages (in thresholds, min/max, demands etc.)

Communication setup and testing

In any display screen, press SELECT x 3 ( blinks), then press ENTER ( blinks),

then x 3 (.) and ENTER to setup the built in RS-485 port (COM1).

If communication module is present, configure also COM2.

Resetting the min/max, energy, demands etc.

In any display screen, press SELECT x 3 ( blinks), then press ENTER ( blinks), then

ENTER to enter the reset menu. Select the value to be reset, press SELECT to select, then press

ENTER for 5 seconds until the  notification is changed to .

WI!

Otros manuales para PM130 PLUS

Otros manuales de Instrumento de medición de Satec

Satec

Satec PM130 series Manual de usuario

Satec

Satec PM172P Manual de usuario

Satec

Satec expertmeter EM720 Manual de usuario

Satec

Satec PM171 series Manual de usuario

Satec

Satec PM135 Manual de instrucciones

Satec

Satec PNA295-1 Manual de usuario

Satec

Satec PM290 Manual de usuario

Satec

Satec PRO EM235 Manual de instrucciones

Satec

Satec Expertmeter PM180 Manual de usuario

Satec

Satec expertmeter EM720 Manual de usuario

Satec

Satec PM172EH Series Manual de usuario

Satec

Satec PM172 Series Manual de usuario

Satec

Satec EM133 Manual de usuario

Satec

Satec EM132 Manual de usuario

Satec

Satec PM172 Series Manual de usuario

Satec

Satec expertmeter EM720 Manual de usuario

Satec

Satec PM175 Series Manual de usuario

Satec

Satec PM172EH Series Manual de usuario

Satec

Satec Expertmeter PM180 Instrucciones de instalación y funcionamiento

Satec

Satec PM130 PLUS Manual de usuario

Satec

Satec PM130P Manual de usuario

Satec

Satec PM130 series Manual de usuario

Satec

Satec PM172 Series Manual de usuario

Satec

Satec PM130 PLUS Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario