Sat Cruiser DSR-301 ACE Manual de usuario
User Guide
DSR - 301 ACE
INFORMATION TO THE USER
II
INFORMATION TO THE USER
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
WARNING
Information contained in this manual is subject to change without notice. No part of this
publication may be copied, reproduced, or translated to another language for any
purpose.
FOR YOUR SAFETY
Be sure to read the user manual before starting the operation of the receiver.
Do not open the housing. The receiver contains high-voltage components and parts.
Do not expose to rain or moisture.
Do not make objects or fluid enter the housing through the ventilation slot. If any
spilt liquid went into to the housing, unplug the power cord and call your local service
provider.
Do not place close to any heat source.
Do not press with hard or heavy object.
To protect possible malfunction by lighting, we recommend you to use power surge
unit. Call your local dealer for advise.
For Your Safety
1. Before Getting Started 1
1.1 Main Features 1
1.2 Accessories 2
2. Controls and Functions 3
2.1 Front Pannel 3
2.2 Rear Pannel 4
2.3 Remote Control Unit 5
3. Connections 7
3.1 Connecting to the TV, VCR and Satellite Antenna 7
3.2 Connecting to the TV, HiFi system and 0/12V switch 8
3.3 Connecting DiSEqC switch 8
3.4 Connecting CA Module 9
4. Settings and Operations 10
4.1 Basic Settings 10
4.2 Viewing TV(or Radio) 13
4.3 Other functions 17
4.4 System Settings 18
4.5 CA Information 21
5. Appendix 22
5.1 Troubleshooting 22
5.2 Specification 22
5.3 Glossary 23
III
CONTENTS
1.1 Main Features
Easy Menu Function
TV Guide Function
RF Output Function
Electronic Program Guide(EPG) for On Screen Channel Information
Software Upgrading Function Through RS-232C Cable by PC
Perfect DiSEqC 1.2 and 0/12V Support for Various Antenna System or 2-LNB on 1
Antenna System
Supports of Ku/C band, SCPC and MCPC
Additional Audio Output Function for Connection to Hi-Fi Audio System
Other Functions of Remote Controller, Receiving Level Selection, Channel Editing,
Menu Language Selection and Audio Selection
Digital free-to-air Satellite Receiver
NTSC & PAL Output Function
Regardless of the TV type, NTSC and PAL channels can be viewed by selection
When PAL channel is viewed on NTSC TV, small deletion on up & down sides of the screen
may occur and it is normal, as its conversion is managed by software. And darker color on the
bottom side of the screen may occur, when NTSC channel is viewed on PAL TV.
500 Transponders and 2000 Channel Memory Function
Teletext Supported
Multi Language Function(Menu, Audio)
Before Getting Started
1
1.2 Accessories
User Manual
Battery
Remote Control Unit
RCA cable
2
Accessories
2.1 Front pannel
STANDBY ON
Turn the power on/off.
MENU
Shows the menu application.
Channel
Change channel, move menu, or input frequency value.
Volume
Control volume, change item on menu or input frequency value.
OK
Select menu or value on menu item.
CI Slot
Insert CI module into CI slot.(It is needed for only model contained Common Interface
function)
CONTROLS AND FUNCTIONS
3
2.2 Rear pannel
DIGITAL
It receives signals from the LNB in the range of 950 ~ 2150MHz. Connect a satellite dish
to DIGITAL.
OUT
It sends signal to the another receiver.
RS-232C
It receives data by connecting to PC for software upgrading. Connect with RS-232C
cable a PC and receiver.
AUDIO
It provides stereo audio output. Connect the audio on TV to AUDIO with RCA cable.
VIDEO
It provides composite video output. Connect the Video on TV to VIDEO with RCA cable.
0/12 VOLT
It provides 0 or 12V output for external LNB switch.
TV ANT IN
The signal supplied to this connector from a TV antenna will be sent to TV antenna
output. Connect a TV antenna to TV ANT IN.
TV output
It provides a modulated audio and video from the receiver. Connect the TV/VCR on TV to
TV/VCR with the RF cable.
ON/OFF
The switch is to turn on or off the main power of the receiver mechanically.
4
Rear pannel
2.3 Remote Control Unit
CONTROLS AND FUNCTIONS
5
POWER
Turn the power on/off.
TV/SAT
Select between TV Channels and Satellite
channels for RF output.
Numeric(0~9)
Move menu, change channel or input
frequency value.
CLEAR
Clear wrong number input or delete channel
from TV (Radio) list or favorite channel list.
MUTE
Deactivate current sound.
MENU
Shows the menu application.
EXIT
Exit from the menu.
Page UP/DOWN
Move to previous/next page on TV(Radio),
Favorite Channels or Edit TV(Radio)
Channels.
Volume
Control volume, change item on menu or input frequency value.
Channel
Change channel, move menu, or input frequency value.
OK
Select menu or value on menu item.
Open the controller cover on the back and insert two batteries (AA - 1.5V).
PROGRAM GUIDE
Shows the broadcasting information.(Video - Audio - LNB)
INFORMATION
Shows the information of current channel. Click the INFO button twice, TELETEXT mode
will be displayed.
FAVORITE
Add TV or Radio channel to the favorite list on Edit TV(Radio) Channels, or watch favorite
channel from your favorite list.
TV
Change to TV mode from radio channel.
RADIO
It is for fast changeto radio mode from TVchannel. Shows thecurrent Radio programlist.
FLASH BACK
It is to move to previous channel.
MULTI LANGUAGE
Select the audio language from 2 or more audio language channels available.
MULTI AUDIO
Select Stereo, Main or Sub from multi language channels available.
SCREEN SIZE
Select between standard 4:3 and wide 16:9 screen sizes.
*ANA/DIGI
Change between analog mode and digital mode.
*OSD
When analog satellite signal is received, it is to turn OSD on or off.
TEXT
Change to Teletext mode.
**WEST/EAST
The function of EAST/WEST button is to move the Position Actuator
westward/eastward.
Buttons marked with * operate only in model contained analog function.
Buttons marked with ** operate only in model contained positioner function.
6
Remote Control Unit
Note
Connections
7
3.1 Connecting to the TV, VCR and Satellite Antenna
It is not necessary to adjust power, as the product is of free - voltage (100 ~ 240V )
1. Connect the RF cable from the TV OUTPUT on the satellite receiver to a TV and
connect the RF modulate on the VCR and the TV ANT.IN.
3. Connect an antenna to the LNB socket on the VCR or other receiver and cable of the
satellite dish to the DIGITAL on the satellite receiver.
Tabla de contenidos
