Sapido IPJC1n Manual de usuario
Sapido
IPJC1n User Manual
V1.0.0
FCC Caution
FCC Part 15.19 Caution:
•This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions
◦this device may not cause harmful interference and
◦this device must accept any interference received, including interference
that may cause undesired operation
•This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
•Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
IMPORT NT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.
FCC Statement in User’s Manual (for calss B)
FCC Section 15.105
“Federal Communications Commission (FCC) Statement”
This equipment has been tested and found to comply with the limits for a lass B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CE Statement of Conformity
Our product has been tested in typical configuration by Ecom Sertech Corp and was
found to comply with the essential requirement of “Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic
Compatibility” (89/336/EEC; 92/31/EEC; 93/68/EEC)
Chapter 1.Introduction
With its built-in high performance image and voice sensor, the IPJC1 be placed in
your living room, office, or anywhere else, you would like to keep an eye on things,
with no PC required and building surveillance where clearer video and more image
detail are required. IPJC1 integrate IPCAM 、speaker 、USB port in the wireless
router .It is accessible via the LAN or internet connection, Connect the product
directly to a local area network or XDSL modem, the video can be saved in a storage
and delivered to you cell phone or computer. the IPJC1 is a perfect solution for
combined the safe monitor and home entertainment.
Chapter 2. Main Features
Support H.264 MJPEG Compression
The product support H.264 and MJPEG Compression and maximum Frame rate and
resolution is 30fps at 1280X1240(1.3Mega-Pixal),It provides high quility images for view and
record.
2-Way audio commuication
The product built-in a high sensitivity capacitive microphone ,and allows user to listen and
talk remotely.user also can adjusts the sensitivity level of microphone via web browse to
decide how much sound level will be captured.
Support motion and audio detection
When the camera detects movement, the IPJC1 can send a message to alert and recode
the pictures in storage. It help user to monitor the environment in home or office.
Built-in Speaker
IPJC1 also support a speaker.It can be used to play music in local network(LAN) or send the
voice from remote device(PC or cellphone)
Easy to configure and manage
With convenient Web-based UI, user can configure easily and browse system information
and status. IPJC1 can detect 3.5G system and connect to Internet automatically. If user
changes Internet-connecting way to Ethernet, IPJC1 will detect it and connect Internet
automatically.
USB File Sharing
IPJC1 supports one USB 2.0 port .plug-in usb disk to be storage or plug-in 3.5G dongle to
be a WAN interface.
USB port also can support devices as below
Support 3.5G USB dongle
Support Smart Phone
Support USB Storage、USB HDD
Chapter 3. Panel Layout
3.1The Front Panel
NO. LED Function Color Status Description
1Power *1 Power indication Green On Power is being applied to this
product
Wireless/
WPA
Wireless/WPS
indication
Green On Wireless is enable
Green Blinking3
0ms
Data is transmitting or receiving
Red Blinking WPS Enable
3WAN WAN port
activity
Green On 10/100 Mbps Ethernet is connected
Blinking3
0ms
100 Mbps Ethernet Tx/Rx activity
Blinking1
0ms
10 Mbps Ethernet Tx/Rx activity
4LAN LAN port
activity
Green On 10/100 Mbps Ethernet is connected
Blinking3
0ms
100 Mbps Ethernet Tx/Rx activity
Blinking1 10 Mbps Ethernet Tx/Rx activity
0ms
5Webcam
ststus
Webcam status Green On Webcam is ready
Red Blinking Recording image
6 Speaker
power
Speaker enable Green On Speaker is ready
3.2 The Real Panel
The following parts are located on the rear panel
POWER: The Power socket is where you will connect the power adapter.
Reset: Pressing this button for more than 5 seconds for default reset IPJC1.
USB Port: Connect to the USB Device,ex USB storage or 3.5G dongle
L N PORT: connect the Router to the PC or Ethernet
W N: This WAN port is where you will connect the DSL/cable Modem, or Ethernet
Mode switch switch to “Router more” or “AP mode” or “WIFI AP mode”
Volume up: adjust the sound level up
Volume down: adjust the sound level down
audio in: Connect with cell phone or PC and the audio source will play from IPJC1
3.3 The Top Panel
Record button: Press the button to record the video.
USB Port: Connect to the USB Device,ex USB storage or 3.5G dongle
Chapter 4.Connecting the Router
1.Power On the IPJC1,waiting for 30 seconds
2.PC connect to the one of LAN port of IPJC1 by RJ-45 cable
3.ADSL or upper Router connect to WAN port of IPJC1
4.Open the pc’s browser(ex IE) and key-in 192.168.1.1 in address bar, if connection is fine,you
can connect to IPJC1 and show the login page. Please key in the account and password,the
Default Value is “admin”
•Users can set or change user name and password for accessing the web management
interface in this section.
•Input New Password, then input confirm password again.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
