Sangean RCR-22 Manual de usuario
RCR-22
Version 1
GB
1
GB
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.
Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does not fit
into your outlet. Consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Important safety instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
2
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused
for long periods of time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged. liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
To Reduce the Risk of Fire or Electric Shock, Do not Expose
This Appliance To Rain or Moisture.
The Shock Hazard Marking and Associated Graphical Symbol
is provided on the rear of unit.
11.
12.
13.
14.
15.
16.
3
GB
Apparatus shall not be exposed to dripping or splashing and no
objects lled with liquids, shall be placed on the apparatus.
Excessive sound pressure on ear- and headphones could
impair the hearing ability. Higher setting that idle on the
equalizer leads to higher signal voltages on the output for ear
and headphones.
The power plug should be close to the radio, and easy to be
approached that during the emergency, to disconnect the power
from the radio, just unplug the power plug from the AC power
slot.
Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnected device shall remain readily
operable.
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any
change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s
authority to operate the device.
17.
18.
19.
20.
4
5
GB
Controls
Menu button
Preset button
Tuning up / down button / Snooze button
Band / Select button
Time capsule
Date button
Time button
Alarm 2 button
Alarm 1 button
Display
Power button / Sleep button
Nap button
Info button
Light button
Reset button
Light level control
Aux in socket
Headphone socket
2
1
3
5
7
18
17
16
15
14
13
12
11
10
9
4
6
8
6
LCD display
Time and frequency indicator
Radio-controlled time signal
RDS indicator
Sleep / Snooze indicator
Nap indicator
Alarm 1 with buzzer alarm indicator
Alarm 1 with radio alarm indicator
Alarm 2 with buzzer alarm indicator
Alarm 2 with radio alarm indicator
FM stereo indicator
Signal level indicator
H
G
F
E
D
C
B
A
K
J
I
7
GB
Using the clock radio for the rst time
1. Place your clock radio on a at surface.
2. Fully extend the wire aerial located on the rear of your clock radio.
Place the wire antenna so that it is straight as possible extending
either above or below the radio.
3. Insert the adaptor plug into the AC socket located on the rear of
your clock radio. The display will show "time zone" for a few
seconds and then the display will ask you to set your time zone.
To set the time zone, press the Tuning up/down button and the
Select button to conrm. Your clock radio will show _ _: _ _ on the
display and the indicator will ash. The radio will scan for signal
and if a signal is found and received completely it will then show
on the screen without ashing. Now the radio will show the
current time.
4. If no signals are found, will be ashing on the display. It may
be necessary to relocate your clock radio to a position giving better
reception.
IMPORTANT:
The mains adaptor is used as the means of connecting the clock
radio to the mains supply. The mains socket used for the clock
radio must remain accessible during normal use. In order to
disconnect the radio from the mains completely, the mains adaptor
should be removed from the mains socket outlet completely.
Characters appearing on the LCD display indicates the clock radio
is connected to and powered from the mains supply.
8
Clock
Manual clock setting (only if automatic setting fails)
1. Press and hold the Time button to enter the clock setting, and
the hour digits will ash on the display.
2. Press the Tuning up or down button to adjust the hours. Then
press the Band/Select button to conrm the setting. The minute
digits will ash on the display.
3. Press the Tuning up or down button to adjust the minutes. Then
press the Band/Select button to confirm the setting. Now the
clock setting is completed.
Manual date setting (only if automatic setting fails)
1. Press and hold the Date button to enter the date setting and then
the year digits will ash.
2. Press the Tuning up or down button to adjust the year. Then
press the Band/Select button to conrm the setting. The month
digits will ash.
3. Press the Tuning up or down to adjust he month. Then press the
Band/Select button to conrm the setting. The date digits will ash.
4. Press the Tuning up or down button to adjust the date. Then
press the Band/Select button to conrm the setting. Now the time
setting is completed.
9
GB
Change 12/24 hour clock format
1. Press the Menu button to enter the setting.
2. Press the Tuning up or down button until ‘CLOCK 24H’ is highlighted
on the display. Press the Band/Select button to enter the setting.
3. Press the Tuning up or down button to choose 12/24 hour clock
format. Press Band/Select button to conrm the setting.
Change date format
1. Press the Menu button to enter the setting.
2. Press the Tuning up or down until date format is highlighted on
the display. Press the Band/Select/button to enter the setting.
3. Press the Tuning up/down button to choose your desired format.
Press Band/Select button to conrm the setting.
D.S.T. (Daylight Saving Time)
1. Press the Menu button to enter the menu setting.
2. Press the Tuning up or down button until ‘DST OFF’ is appeared
on the display. Press the Band/Select button to enter the setting.
3. Press the Tuning up or down button to choose ‘+1H’ (activated
D.S.T.) or ‘OFF’. Then press the Band/Select button to conrm
the setting.
Otros manuales para RCR-22
7
Tabla de contenidos
Otros manuales de Radio reloj de Sangean
Sangean
Sangean CR-220DFM Manual de usuario
Sangean
Sangean RCR-40 Manual de usuario
Sangean
Sangean Sangean RCR-5 Manual de usuario
Sangean
Sangean DCR-9 Manual de usuario
Sangean
Sangean RCR-29 Manual de usuario
Sangean
Sangean ProTravel PT-50 Manual de usuario
Sangean
Sangean Sangean- RCR-3 Manual de usuario
Sangean
Sangean RS-332 Manual de usuario
Sangean
Sangean RCR-10 Manual de usuario
Sangean
Sangean Sangean RCR-5 Manual de usuario
Sangean
Sangean RCR-4 Manual de usuario
Sangean
Sangean RS-330 Manual de usuario
Sangean
Sangean RS-330 Manual de usuario
Sangean
Sangean RCR-2 Manual de usuario
Sangean
Sangean RCR-8WF Manual de usuario
Sangean
Sangean RCR-2 Manual de usuario
Sangean
Sangean RCR-22 Manual de usuario
Sangean
Sangean RCR-40 Manual de usuario
Sangean
Sangean UCR-100 Manual de usuario
Sangean
Sangean RCR-24 Manual de usuario
