Samsung OfficeServ 7000 Series Manual de instrucciones

System Administration Guide

www.samsung.com/bcs

FFEEAATTUURREESSAANNDDSSPPEECCIIFFIICCAATTIIOONNSS

0 Call attendant or system operator

10 + xxx Retrieve parked calls

11 Put calls on and take calls off hold

12 + xxx Retrieve calls on hold at

another station

13 Door lock release

16 + xxx Make speed dial calls

17 Save number and redial it

18 Recall dial tone for new call

19 Last number redial

2xx or 2xxx Extension numbers

3xx or 3xxx Extension numbers

400 Cancel do not disturb

401 Set do not disturb

41 Set message no ring

42 + xxx Cancel message

43 Set/return messages

44 Busy station/line callback

45 Busy station camp-on

46 Set up a conference

47 Enter account code

48 Set programmed station message

49 Send flash to outside line

5xx or 5xxx Station hunt groups

55 + 0 Page internal zone zero

55 + 1 Page internal zone 1

55 + 2 Page internal zone 2

55 + 3 Page internal zone 3

55 + 4 Page internal zone 4

55 + 5 Page external zone 1

55 + 6 Page external zone 2

55 + 7* Page external zone 3

55 + 8* Page external zone 4

55 + 9 Page all external zones

55 + All page

56 Meet me answer

57 Alarm sensor clear

58 DISA alarm clear

59 Walking class of service

600 Cancel all call forwarding

601 + xxx Set forward all calls

602 + xxx Set forward busy

603 + xxx Set forward no answer

604 + xxx Set fwd busy/no answer

605 + xxx Set forward on DD

606 + xxx Set forward follow me

65 Directed call pickup

66 Group call pickup

67 Universal answer

7xx or 7xxx Individual line numbers

8xx Trunk groups

9 Trunk group 9 (local)

The OfficeServ telephone systems have preset (default) feature access codes that use the following

number plan. These codes can be used if a key is not available for the feature you want to use.

Standard telephone users must always dial these codes.

05/07

*External zone 3 and 4 not available on the OfficeServ 7100.

System_Administrator_Guide_Cover.qxp 4/30/2007 3:32 PM Page 1

SYSTEM

ADMINISTRATION

AND

SPECIAL FEATURES GUIDE

for

OfficeServ™ 100, OfficeServ™ 500

OfficeServ™ 7000 Series

April 2007

Samsung Telecommunications America reserves the right without prior notice to revise information in

this guide for any reason. Samsung Telecommunications America also reserves the right without prior

notice to make changes in design or components of equipment as engineering and manufacturing

may warrant. Samsung Telecommunications America disclaims all liabilities for damages arising from

the erroneous interpretation or use of information presented in this guide.

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 1

TABLE OF CONTENTS

ABOUT THIS BOOK .................................................................................... 1

SPECIAL FEATURES

System Ring Plans .......................................................................................................... 2

Manual Ring Plan Change ............................................................................................ 2

Temporary Ring Plan Override ....................................................................................2

Calling The System Operator ...................................................................................... 3

Operator Recalls .............................................................................................................. 3

Executive Barge-in .......................................................................................................... 3

Walking Class of Service ................................................................................................4

In/Out of Group ................................................................................................................4

Direct Inward System Access (DISA) ........................................................................ 5

DISA Security .................................................................................................................... 6

Forced Account Codes ............................................................................................ 6–7

Authorization Codes ...................................................................................................... 7

Using the Tie Line ...................................................................................................... 7–8

CALLER ID SPECIAL FEATURES

Abandon Call List ............................................................................................................ 9

CID on SMDR ....................................................................................................................9

Number to Name Translation ......................................................................................9

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 2

SYSTEM ADMINISTRATOR PROGRAMMING

Customer Level Access .............................................................................................. 10

Customer Level Access Using the PROG Key ......................................................10

Change Feature Passcode ..........................................................................................11

Set Date and Time Display ................................................................................ 11–12

Reset Station Passcodes to Default ................................................................ 12–13

Program Station Names........................................................................................13–15

Program Trunk Names..................................................................................................16

Program Station Group Names ................................................................................17

Program System Speed Dial Numbers .......................................................... 18–20

Program System Speed Dial Names........................................................................20

Program Personal Speed Dial Numbers for Other Stations ....................21–23

Program Personal Speed Dial Names for Other Stations ........................23–24

Create Programmed Station Messages ........................................................ 24–25

Set Alarm/Appointment Reminder with Message .................................... 25–26

Managing Key Assignments ............................................................................ 27–28

Programming Account Codes ..................................................................................29

Station Timers ..........................................................................................................30–31

Adding Names to the Translation Table ........................................................31–32

Holiday ..............................................................................................................................33

Customer Set Relocation......................................................................................34–35

SYSTEM MAINTENANCE ALARMS ......................................36

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 3

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 4

ABOUT THIS BOOK

This book contains instructions for special features that every telephone user may

not need to know.The owner can decide who the system administrator will be and

who will have access to these features. Station users can be trained on only the

items that apply to them. This procedure will help control costs and telephone

abuse.

Several of the features listed in this book are specific to the system operator or

attendant position.You can have more than one operator or set your system up to

be used without an operator.

The designated system administrator can access specific programs and modify

some functions to better manage the OfficeServ 100, OfficeServ 500, OfficeServ

7000 Series office telephone systems. Instructions are detailed and easy to follow.

When assistance is needed, contact your installation and service company.

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 5

SPECIAL FEATURES

SYSTEM RING PLANS

Your system is designed to have a maximum of six different Ring Plans. Each ring

plan can be programmed to allow different lines to ring different ring plans to ring

different station and/or station groups. Examples of why different ring plans are

required can include normal day operation, night operation, using different oper-

ators during different lunch shifts and Saturday or evening hours of operation.

While the system is in a ring plan, each station will be limited to its individual Ring

Plan class of service dialing restrictions.You can place the system in one of any six

of these ring plans at any time. Ring Plans are available on an individual tenant

basis and may be set automatically or manually. Automatic Ring Plans have an

individual start time and will remain in that mode until the beginning of the next

defined ring plan. If no automatic timer is set, you must change ring plans manu-

ally.

Any of these ring plans can be switched from one plan to another at any time by

manually pressing a ring plan button. There are two ways to override the auto-

matic ring plans; one is a temporary override until the next programmed start

time, and the other is a permanent override until manually changed.

MANUAL RING PLAN CHANGE

Press the RTO button plus the ring plan passcode (four digits) and the ring plan (1-

6) you wish to set. The system will override all the automatic time tables and will

remain in the set ring plan until manually changed. To manually change or cancel

the ring plan time override and return ring plan operation to the system clock:

press the RTO plus the ring plan passcode (four digits) and a “0” to cancel the ring

plan time override and return to normal operation.

TEMPORARY RING PLAN CHANGE

Press the RP button plus the ring plan passcode (four digits) and the ring plan (1-

6) you wish to set.The system will remain in that ring plan until the next automat-

ic start time for the next ring plan goes into effect.

NOTE: This button may also be assigned an extender of one of the six ring plans.

Example: An RP button is given an extender of 3 (RP3) and the operation of this

button is a push on/push off type of operation with the system always returning

to ring plan 1 when the key is turned off.When the system is operating in ring plan

3, the RP3 button will light steady red, and when off the light will also turn off.

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 6

CALLING THE SYSTEM OPERATOR

Any station that dials 0will ring its assigned operator. (If tenant service is used,

each tenant may have a different operator or operator group.) Calls to the system

or tenant operator are easily identified because the CALL key will have a fast flash-

ing red light. Station users will never receive a busy signal when they dial 0or the

operator group number. The calls will continue ringing in queue until answered.

NETWORKING: When 2 or more systems are networked a single station or

operator group may receive all calls to a single operator. (Please consult with your

service company if required).

OPERATOR RECALLS

Transferred calls that go unanswered will recall to the station that originated the

transfer. Should the station that originated the transfer not answer the recall, the

call will be sent to the operator as a transfer recall.

A call left on hold will recall the station that put it on hold. If the hold recall is unan-

swered at the station that originated the hold, the call is sent to the operator.

Both types of recalls will ring and have a slow flashing amber light on the LINE key

or CALL key.

NETWORKING: When 2 or more systems are networked a single station or

operator group may receive all recalls to a single operator. (Please consult with

your service company if required).

EXECUTIVE BARGE-IN

If you want to break into another conversation, you must be allowed to barge-in

and the other station and trunk must not be secure.

• Dial the desired extension or trunk number and listen for the busy signal.

• Press the BARGE button and begin speaking after the tone.

• Hang up when you are finished.

The system can be set for one of the three following barge-in options:

• No barge-in allowed

• Barge-in with intrusion tone

• Barge-in without intrusion tone (service observing)

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 7

When the second or third option is selected the barger will take priority over the

line. This means unless you (barger) hang up first, the station or line you barged

into will still be connected to you when the station you barged into hangs up.

When the third option is selected, the station that barges-in can monitor the con-

versation and no warning tone or display will be sent to the station being moni-

tored.The handset transmitter and keyset microphone are disabled.The party that

originated the barge-in may join the conversation by pressing the MUTE button

on the keyset.Your service company must program these options for you.

WARNING

Barge-in without tone may violate state or federal laws concerning the

right to privacy. Samsung Telecommunications America is in no way

responsible for the possible misuse of this feature.

WALKING CLASS OF SERVICE

You can change a restricted station’s class of service to the same class as your sta-

tion, allowing you to make calls or use features that would otherwise be restricted

from that station.

• Lift the handset or press the SPK or the MONITOR key.

• Dial 59 and then your extension number.

• Dial your station passcode and receive internal dial tone.

• Dial an access code and then the telephone number—OR—use the desired

feature as usual.

• Hang up.The station will be returned to its restricted status.

NOTE: The default station passcode 1234 cannot be used.

IN/OUT OF GROUP

Any station assigned to a station group can remove itself from that group and

then reenter the group at a later time.When out of the group, a station can receive

calls to its extension number but not to the group.

The number of groups available to choose from may vary depending on your

OfficeServ 100 or OfficeServ 500 or OfficeServ 7000 Series system type:

OfficeServ 500 40 Groups

& OfficeServ 7200 (500 through 539) or (5000 through 5039 depending if your

system is setup for 4 digits numbering plan)

OfficeServ 500 L 80 Groups

& OfficeServ 7400 (500 through 579) or (5000 though 5079 depending if your

system is setup for 4 digits numbering plan)

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 8

OfficeServ 100 20 Groups

& OfficeServ 7100 (500 through 519) these can be changed to 4 digits if

required.

To create a backup or relief operator position,assign the main operator and one or

more backup individuals to the operator group. All but the main operator should

be out of the group.When it is necessary to use a backup operator, put the desired

backup station in the group and remove the main operator. When incoming call

traffic is heavy, you can have another station put itself in the operator group along

with the main operator to handle the extra call load.

If the station does not have an IN/OUT key:

• Lift the handset and dial the feature access code _________________.

• Dial the group number.

• Dial 0to be out of the group or dial 1to be in the group.

• Receive confirmation tone and hang up.

If the station has an IN/OUT key:

• Press the IN/OUT key. It will light red when the station is in the group.

• Press the IN/OUT key again. The light is off when the station is out of the

group.

NOTE: A station can be in more than one group.

DIRECT INWARD SYSTEM ACCESS (DISA)

From outside of the office, selected individuals can call into the OfficeServ 100 or

OfficeServ 500 or OfficeServ 7000 Series system on special DISA line(s). A security

code must be entered to gain access. Once these individuals are in the system,

they can make outside calls using the office lines or call stations within the system.

Individuals who will use DISA must have their stations assigned for DISA access

and must change their station passcodes. The default passcode 1234 cannot be

used.

• Call in on the DISA line from any phone with tone dialing.

• You will hear a dial tone. Dial your security code (your extension number

plus your station passcode).

• If you are allowed access, you will receive a dial tone.

• Dial any line access code, receive outside dial tone and then dial a tele-

phone number OR dial any extension number to call a station in the sys-

tem.

• To make another call, press Q, receive dial tone and dial another number.

• Press #and hang up when finished.

System_Administration_Guide.qxp 4/30/2007 12:56 PM Page 9

Otros manuales para OfficeServ 7000 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema telefónico de Samsung

Samsung

Samsung DCS-816 Manual de usuario

Samsung

Samsung OFFICESERV 500 Series Instrucciones de funcionamiento y mantenimiento

Samsung

Samsung NX-828 Manual de usuario

Samsung

Samsung OFFICESERV 100 Series Manual de usuario

Samsung

Samsung DCS-408 Manual de usuario

Samsung

Samsung DCS 400SI Manual de usuario

Samsung

Samsung OfficeServ 7400 Manual de usuario

Samsung

Samsung OfficeServ 7200 Instrucciones de funcionamiento y mantenimiento

Samsung

Samsung OfficeServ 7200 Manual de usuario

Samsung

Samsung OfficeServ 7200 Instrucciones de funcionamiento y mantenimiento

Samsung

Samsung DCS Manual de usuario

Samsung

Samsung iDCS 500 Instrucciones de instalación

Samsung

Samsung OFFICESERV 100 Series Instrucciones de funcionamiento y mantenimiento

Samsung

Samsung DS 616 Manual de usuario

Samsung

Samsung iDCS 500 Manual de usuario

Samsung

Samsung iDCS 100 Manual de usuario

Samsung

Samsung Office Serv 500 Instrucciones de funcionamiento y mantenimiento

Samsung

Samsung DCS-408 Manual de usuario

Samsung

Samsung UbiCell Manual de usuario

Samsung

Samsung iDCS500 Manual de usuario

Samsung

Samsung OFFICESERV 7100 Manual de usuario

Samsung

Samsung OfficeServ 7200 Instrucciones de funcionamiento y mantenimiento

Samsung

Samsung DCS KEYSET Manual de usuario

Samsung

Samsung DCS-816 Manual del propietario

Manuales populares de Sistema telefónico de otras marcas

Teleco

Teleco Perfect Voice Tis 16 Manual de usuario

AT&T

AT&T Network Adapter 25 Manual de usuario

AVE

AVE AF902R-CE Manual de usuario

Tynetec

Tynetec Advent xt Manual de usuario

Ericsson

Ericsson DCT1800-S Manual de usuario

NEC

NEC Electra Elite 192 Manual de usuario

Alcatel

Alcatel EASY REFLEXES 4200 Manual de usuario

Panasonic

Panasonic KX-TDA50 Manual de usuario

Bticino

Bticino PABX 28D Manual de usuario

NEC

NEC SL 2100 Manual de usuario

Sonifex

Sonifex Phone In 6 Manual de instrucciones

TransTel Communications

TransTel Communications TD-824i Instrucciones de montaje

Nortel

Nortel BCM50 Manual del producto

Panasonic

Panasonic KX-TS25B Manual de usuario

ASCOM

ASCOM TD 92375GB Manual del propietario

Karel

Karel MS26S Hoja de información del producto

EnGenius

EnGenius DuraFon PRO Manual de usuario

Teledat

Teledat X130 DSL Manual de usuario