Samsung SVD-4120AW Manual de usuario

SAMSUNG CCTV CAMERA

SVD-4120A/AW

Vandal-Proof Color Dome Camera

INSTRUCTION MANUAL

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

P/No. : 6806-0458-01B

VAN 04. 10

•SAMSUNG TECHWIN CO., LTD.

Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,

Jungwon-Gu,Sungnam,Kyungki-Do,Korea462-703

TEL:82-31-740-8137~41 FAX:82-31-740-8145

•SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)

Closed Circuit Division 40 Seaview Drive, Secaucus NJ 07094,

U.S.A

TEL: (201) 902-0347 FAX:(201)902-0429

•SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)

Samsung House, 1000 Hillswood Drive Hillswood Business

ParkChertseySurreyKT16OPS

TEL:44-(0)1932-45-5308 FAX:44-(0)1932-45-5325

•

TIANJINSAMSUNGOPTO-ELECTRONICSCO.,LTD(TSOE)

7PingchangRd,NankaiDist, Tianjin, P.R China

PostCode:300190

TEL: 86-22-2761-9698 FAX: 86-22-2761-6514

SALES NETWORK

www.samsungtechwin.com

www.samsungcctv.com

This installation should be made by a qualified service person and

should conform to all local codes.

The lightning flash with an arrowhead symbol, within an equilateral triangle is

intended to alert the user to the presence of uninsulated “dangerous voltage”

within the product's enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

INFORMATION-This equipment has been tested and found to comply with limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

WARNING -Changes or modifications not expressly approved by the manufacturer

could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.

Do NOT expose this appliance to rain or moisture.

Thank you for purchasing a SAMSUNG CCTV CAMERA.

Before operating the camera, confirm the camera model and

proper input power voltage. In order that you can understand

this manual thoroughly, we'll introduce our model description.

SVD-4120A Series (410,000 pixels)

• NTSC models • PAL models

SVD-4120AN SVD-4120AP

SVD-4120AWN SVD-4120AWP

Model Description

SVD-4120A X X

• Lens Type

Blank 2.5X, f=3.8~9.5 Vari-Focal Lens

W 2.4X, f=2.5~6.0 Vari-Focal Lens

• Signal System

N NTSC Model

P PAL Model

Lens Type

Signal system

Features Warning

Fine Picture Condition Under Very

Low Illumination (SENSE UP)

1/3 high density CCD and digital

processor permit high quality pictures to

be captured in very low light condition.

High Resolution

The horizontal resolution of 500TV lines

can be achieved by using a high density

CCD having Double Speed 410,000 pixels

SONY CCD, which provides clean,

noiseless and reliable pictures.

Wide Range ATW

The White Balance can be automatically

adjusted in response to light condition so

that you can observe in an appropriate

color balance.

IP66 Approved / Dust and Rain

Resistant

With dust and rain resistant design, the

camera can be installed outside under

building eaves or places that are exposed

to the dust and rain.

SSNR(Samsung Super Noise

Reduction) CHIP

SVD-4120A/AW has an assistant DSP

chip that can remove image noise

efficiently and it shows clean and obvious

image in low luminance

Electronic DAY/NIGHT

In normal or high luminance, camera

maintains color mode. On the contrary, it

get changed into B/W mode in low

luminance.

Auto Iris Vari-Focal Lens Built In

The focal length of lens is 3.8 to 9.5 mm,

equivalent to 2.5x zoom.(2.5 to 6.0mm,

equivalent to 2.4x zoom/SVD-4120AW)

The built-in lens allows the camera to

have a Wider Dynamic Range, therefore

you can use in various applications.

The camera needs periodic inspection.

Contact an authorized technician for inspection.

Stop using your camera when you find a malfunction.

If you use your camera around smoke or unusual heat for a long time, a fire may

be caused.

Do not Install the camera on a surface that can not support it.

Unless the surface is suitable, it could cause falling or other hazards.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not disassemble the camera.

It may result in fire, electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in fire or other hazards.

Contents

Connecting to Monitor

Connecting to Power

Configuration of The Menu

Operating Your Camera

Setting Up The Menu

• CAMERA ID

• BACKLIGHT

• WHITE BALANCE

• MOTION DETECTION

• IRIS LEVEL CONTROL

• SHUTTER SPEED CONTROL

• SESE UP

• GAIN

• SSNR

• SPECIAL

Troubleshooting

Dimention

Specifications

Connection

Precautions

Composition

Name and Function of Each Section

COLORDOME CAMERACOLORDOME CAMERA User’s ManualUser’s Manual

Precautions

Do not install the camera in

extreme temperature conditions.

Only use the camera under conditions

where temperatures are between -10˚C

and +50˚C. Be especially careful to provide

ventilation when operating under high

temperatures.

Do not install or use the camera in an

environment where the humidity is high.

It can cause the image quality to be poor.

Do not install the camera under

unstable lighting conditions.

Severe lighting change or flicker can cause

the camera to work improperly.

Do not touch the front lens of

the camera.

It is one of the most important parts of

the camera. Be careful not to be stained

by fingerprint.

Do not drop the camera or

subject them to physical shocks.

It can cause malfunctions to occur.

Never keep the camera face to

strong light directly.

• If the camera is exposed to spotlight or object reflecting strong light, smear or

blooming may occur.

• Please check that the power satisfies the normal specification before connecting

the camera.

Notes

It can damage the CCD.

Do not expose the camera to

radioactivity.

If it is exposed to radioactivity, For

heated CCD, it will be out of order.

Composition

Name and Function of Each Section

COLORDOME CAMERA User’s Manual

1. SVD-4120A/AW

2. Instruction Manual

3. Quick Install Guide

5. Ø5 Tapping Screws 4EA

6. Template

4. Wrench

7. Video Output Cable for installer

Name and Function of Each Section

COLORDOME CAMERA User’s Manual

Pan Base

control panning angle of camera

Tilt Base Holding Serews

fix tilted position.

Pan Base Holding Screws (Color : Silver)

fix panned position

Zoom Handle

adjust zoom between WIDE and TELE

Focus Handle

afteradjusting zoom, adjustfocus

SET Button

confirm the status of the selected feature

RIGHT Button

move cursor to the right, change the status of the selected feature

DOWN Button

movecursor to thedown, select thedesired feature item

UP Button

movecursor to theup, select thedesired feature item

LEFT Button

move cursor to the left, change the status of the selected feature

Video Output Terminal

Video Output Terminal to Monitor

Video Output Jack

Power Input Jack

Shield Case

Dome Cover

Connection

Connecting to Monitor

Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.

• As the connecting method varies with the instruments, refer to the manual

supplied with the instrument.

• If necessary, you can connect the monitor to the REMOTE jack on the back of

your camera.

• Only connect the cable when the power is turned off.

• Set the 75Ω/ Hi-Z selection switch as shown below if you have an intermediate

device.

CCTV Camera Monitor

CCTV Camera

Intermediate End monitor

COLORDOME CAMERA User’s Manual

Operating Your Camera

Connection

Connecting to Power

• Use AC 24V / 300mA or DC 12V / 500mA power source.

•For DC power as the voltage drop according to the length of the cable in the

abovetable, a cameramay malfunction ifthere is anexcessively long cablerun.

Resistance of copper wire [at 20C˚ (68˚F)]

* Voltage for camera operation: 12V DC ±10%

* Voltage drops in the above table are variable according to types of cable manufacturer.

For DC Power Type

Copper wire size (AWG)

#24(0.22mm2)#22(0.33mm2)#20(0.52mm2)#18(0.83mm2)

Resistance ( Ω/ m) 0.078 0.050 0.030 0.018

Voltage Drop (V/m) 0.028 0.018 0.011 0.006

• Be sure to connect power only after all the installation is complete.

• Note that AC or DC adaptor is not supplied with camera.

• Use the UL listed, class 2 power transformer of AC 24V adaptor.

• Ground should be connected to the GND terminal.

Notes

Configuration of The Menu

SETUP MENU CAMERA ID (see page 17)

• OFF • ON

BACKLIGHT (see page 20)

• WDR • BLC • OFF

WHITE BAL. (see page 21)

• W-ATW • S-ATW • AWC • MANUAL

MOTION DET. (see page 22)

• OFF • MD1 • MD2

IRIS LEVEL CONTROL (see page 25)

• LEVEL

SHUTTER (see page 26)

• OFF • 1/100 (1/120) • MANUAL

SENSE UP (see page 27)

• Auto • OFF

GAIN (see page 28)

• OFF • AGC-L •AGC-H

SSNR (see page 28)

• OFF • LOW • MIDDLE •HIGH

SPECIAL (see page 30)

• COLOR • SYNC • PRIVACY • RESET

• END • EXIT

EXIT

COLORDOME CAMERA User’s Manual

Setting Up The Menu

Operating Your Camera

1. Pressthe SET buttonto access theSETUP mode.

•SETUP menu isdisplayed on themonitor screen.

2. Selectthe desired featureusing the UPor DOWN button.

•Each time you press the UP or DOWN button, the arrow indicator moves up

ordown.

•Move the arrowindicator to thedesired feature item.

Usethe five SETUPMENU buttons onback of thecamera.

RIGHT button

UP button

LEFT button

SETUP

CAMERA ID OFF

BACKLIGHT WDR

WHITE BAL. W-ATW

MOTION DET. OFF

IRIS LEVEL

SHUTTER OFF

SENSE UP OFF

GAIN AGC-L

SSNR MIDDLE

SPECIAL

EXIT

SET button

DOWN button

SETUP

CAMERA ID OFF

BACKLIGHT WDR

WHITE BAL. W-ATW

MOTION DET. OFF

IRIS LEVEL

SHUTTER OFF

SENSE UP OFF

GAIN AGC-L

SSNR MIDDLE

SPECIAL

EXIT

Change the status using

the LEFT or RIGHT button.

Select the function using

the UP or DOWN button.

3. Changethe status ofthe selected featureusing the LEFTor RIGHT button.

4. Whencompleted, move thearrow indicator to'EXIT' and pressthe SET button.

Ifyou enter aCAMERA ID, thename will bedisplayed in thescreen monitor.

1. Press the SET button to display the SETUP menu and move the arrow

indicatorto 'CAMERA ID'using the UPor DOWN button.

2. Set'CAMERA ID' to'ON' using theLEFT or RIGHTbutton.

CAMERA ID

• If the CAMERA ID feature is set to 'OFF', the name

will not displayed in the monitor.

Notes

• For the mode with you can access submenu.

• You can access submenu using SET button.

Notes

SETUP

CAMERA ID OFF

BACKLIGHT WDR

WHITE BAL. W-ATW

MOTION DET. OFF

IRIS LEVEL

SHUTTER OFF

SENSE UP OFF

GAIN AGC-L

SSNR MIDDLE

SPECIAL

EXIT

Operating Your Camera

COLORDOME CAMERA User’s Manual

3. PressSET button.

4. Youcan enter upto 16 characters.

Movethecursortocharacter-enterlocationbyusingtheLEFTorRIGHTbutton.

Selectthe desired characterby using UPor DOWN button.

•Thefactory defualt charactersare A, B,···, a, b,···, ., -,··· 0, 1···,8, 9

Pressthe SET buttonto confirm theblinking character. Thefirst character is

savedandthe cursor inthebottomof the screenmovestothe nextposition.

Repeatssteps , and untilyou create thefull name youwant.

• If you make a mistake while entering name

Move the cursor to ‘CLR’, press ‘SET’ button.

After erasing the character from right to left, correct the character again.

Notes

CANERA ID

POS CLR RESET END

CAMERA ID

POS CLR RESET END

5. Selectthe position atwhich the CAMERAID will belocated on thescreen.

Movethe cursor to'POS' and pressSET button.

TheCAMERA ID isdisplayed on thebottom-left of themonitor screen.

(Defaultposition)

Selectthe position byusing the 4-directionalbuttons, then pressthe SET

buttonto confirm theposition.

6. Whencompleted, move thecursor to 'END'and press SETbutton.

FRONT DOOR

CAMERA ID

POS CLR RESET END

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Samsung

Samsung

Samsung SCC-C4253 Manual de usuario

Samsung

Samsung SCB-6001 Manual de usuario

Samsung

Samsung SCC-B5352N Manual de usuario

Samsung

Samsung SNV-5080 Manual de usuario

Samsung

Samsung iPolis SNV-7080R Manual de usuario

Samsung

Samsung SNV-5080RN Manual de usuario

Samsung

Samsung HCD-E6070R Manual de usuario

Samsung

Samsung SCO-6023R Manual de usuario

Samsung

Samsung SCC-B2315 Manual de usuario

Samsung

Samsung SCC-C4301 Manual de usuario

Samsung

Samsung SCC-B9221 - IR Bullet Camera Manual de usuario

Samsung

Samsung SNP-3370TH Manual de usuario

Samsung

Samsung SCD-3083 Manual de usuario

Samsung

Samsung SCC-643(P) Manual de usuario

Samsung

Samsung SNV-5080N Manual de usuario

Samsung

Samsung SNV-7084 Manual de usuario

Samsung

Samsung SVD-4300 Manual de usuario

Samsung

Samsung SID-560 Manual de usuario

Samsung

Samsung SNC-B2335 Manual de usuario

Samsung

Samsung SCC-B5354 Manual de usuario

Samsung

Samsung SID-460 Manual de usuario

Samsung

Samsung SDC-313 SERIES Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Samsung

Samsung SCC-C4239P Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario