Samsung SMT-I3105 Manual de usuario

SMT-i Series Phones

Quick Reference Document For Administrator

V0.3

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

TABLE OF CONTENTS

Introduction ........................................................................................................... 2

Quick Overview ...................................................................................................... 3

SMT-i5264 AOM (Add-On Module) ........................................................................ 4

Quick Setup Guide.................................................................................................. 5

Initial Configuration............................................................................................ 5

SMT-i5264 AOM (Add-On Module) ..................................................................... 6

Quick Software Upgrade Guide .......................................................................... 9

Service/Usage Tips............................................................................................... 13

External USB Port Specifications .......................................................................... 16

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

Introduction

This quick reference document briefly describes the steps for administrator to set up

the SMT-i3105/5200 series IP devices and to upgrade software on these devices.

These new SMT-I series of IP devices required to have OfficeServ 7000 MP software

v4.46 and up. No license is required to register and to operate these devices.

Preparation:

•OfficeServ 7000 system with v4.46 and up software

•Connect OfficeServ 7000 MP, MGI, PC and SMT-ixxxx to the same data network

•Power SMT-ixxxx devices either by PoE or AC power adaptor

MMCs:

•MMC 727: check software version number

•MMC 830: MP IP address

•MMC 840: IP set information

•MMC 209: AOM paring

•MMC 722: Station key programming

Two methods to enter to the engineering mode:

1. Initial setup

a. Press and hold * key while powering up SMT-i3105/5210/5220/5230

phone

i. There is no need to press any key while powering up SMT-i5243.

When powering up the SMT-i5243 the first time, it will automatically

enter the installation menu.

2. Subsequent setup

a. Press *153# while phone displays the phone information. Follow the

following sequence to display the phone information.

i. Menu -> Settings -> phone info; for i3105/5210/5220/5230

ii. Menu -> Phone -> phone information; for i5243

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

Quick Overview

In order to set up the phone or perform the software upgrade, the administrator needs

to enter the phone to the engineering mode.

i3105/i5210/i5220/i5230 i5243

Initial setup

•

Enter to the engineering mode

•Select “Easy Install”menu to set

up the phone

•Power up the phone and

follow on screen instructions

Re-configuration

•Enter to the engineering mode

•Select “Easy Install”menu to set

up the phone

•Enter to the engineering mode

•Select “Easy Install”menu to

set up the phone

Software Upgrade •Run TFTP server software on PC •Run TFTP/HTTP server

software on PC

Method 1: pull from

the phone (phone is

required to register

to the system)

•Enter to the engineering mode

•Select “S/W upgrade”

•Select “TFTP Server”and enter the

PC IP address

•Start upgrade

•Enter to the engineering mode

•Select “S/W upgrade”

•Select “TFTP or HTTP”type

and enter the PC IP address

•Start upgrade

Method 2: push

from MMCs (phone is

required to register

to the system)

•MMC 841:

oEnter PC (server) IP

address

oEnter 4 digits software

version

•MMC 840; enable and start

software upgrade

•MMC 841:

oEnter PC (server) IP

address

oEnter 4 digits software

version

•MMC 840; enable and start

software upgrade

Method 3: use USB

memory (phone is

not required to

registered to the

system)

•Copy software to the root

directory of the USB memory

•Plug-in USB memory to the

phone

•Enter to the engineering mode

•Select “Software upgrade”

•Select “USB”type

•Start upgrade

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

SMT-i5264 AOM (Add-On Module)

1. Setup

•Enter AOM to the set up mode

•Two methods to set up the AOM

oUse SMT-i5243 phone to set up the AOM

oUse web browser to set up the AOM

2. Software upgrade

•Run TFTP server software on the PC

•Use web browser to access the AOM and upgrade the software

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

Quick Setup Guide

Initial Configuration

SMT-i3105/5210/5220/5230 IP Phones

•Press and hold ‘*’key while powering up the phone to enter the configuration

menu.

•Select “Easy Install”

oSelect Dynamic IP if DHCP service is available.

If select static IP address, the IP address must be in the same subnet range

as the OfficeServ system.

oSelect OSPP (KP) as the system type

oSkip unused settings such as VLAN, 802.1x, etc.

oEnter OfficeServ system IP address

Ex. 192.168.1.10

oEnter system ID. This is the phone ID found in MMC 840.

Ex. 3201

oEnter password. This is the phone password found in MMC 840.

Ex. 1234

SMT-i5243 Phones

•Power up the phone and follow the on screen instructions.

oPress Next to advance to next screen

oPress Next to skip language and key pad type

oEnter

Server IP: 192.168.1.10 (OfficeServ system IP address)

ID: 3201 (phone ID)

Password: 1234 (phone password)

Server type: OfficeServ

oPress Next to advance to next screen

oMode:

Select Dynamic IP if DHCP service is available.

If select static IP address, the IP address must be in the same subnet range

as the OfficeServ system.

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

oPress Next to advance to next screen

oSkip unused settings such as VLAN, 802.1x, etc. and press Next

oPress Done

oPress Yes to Finish Easy Install

SMT-i5264 AOM (Add-On Module)

SMT-i5264 AOM will register to the OfficeServ system as an IP phone device. It need

the IP phone ID and password during the registration. The SMT-i5264 will receive an IP

phone extension. It can be paired to any IP phone or digital phone as the add-on

module. MMC 209 is used to pair the AOM extension to a master phone.

•Prepare AOM to the set up mode

oPress and hold 2nd key from the 1st column (left most columns) to enter the set

up mode.

oPress the 3rd key from the 4th column (right most columns) after this key is

flashing.

oTwo method to set up the AOM

•Use SMT-i5243 phone to set up the AOM.

oEnter SMT-i5243 phone to the engineering mode

oMenu -> phone -> phone information -> *153#

oSelect Network -> AOM to enter into the set up mode

oEnter the following data

Press Key 2 first

Then, press Key 51

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

If IP setting is DHCP skip this step

•IP address: (assign an AOM IP address)

•Gateway: (from MMC 830)

•Subnet Mask: (from MMC 830)

Server IP Address: (OfficeServ IP address from MMC 830)

(use navigation key to move to the following fields)

Server ID: (ITP ID from MMC 840)

Server Password: (ITP password from MMC 840)

Server Port: 6000 (press * key twice to switch input mode

to numeric mode)

•Use Web UI

Type IP address with port 8080 in the address bar of IE browser. Default

AOM IP address is 10.0.0.3.

Ex.

•http://10.0.0.3:8080

•ID: admin

•Password: samsung

Fill in the required data. Must enter the following information.

•Server IP address is the OfficeServ MP IP address

oEx. 192.168.1.10

•Enter an ITP ID and password

Ex:

oid: 3210

opw: 1234

•default port is 6000

Press [Save] then [ReStart]

•Use MMC 209 to pair AOM to any IP/TDM phone.

•Use MMC 722 to assign buttons.

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

Re-Configuration

•Enter to the engineering mode

•Select the “Easy Install”item to re-configure the phone

SMT-i SERIES QUICK REFERENCE DOCUMENT

ADMINISTRATOR DOCUMENT MAY 2010

Quick Software Upgrade Guide

•Register phones to the OfficeServ system

•Connect the PC to the same data network and set the TCP/IP properties to the same

subnet range

•Run server software on the PC and point root directory to the phone software folder

•Start phone software upgrade either by pulling from the phone or pushing from the

OfficeServe system

TFTP server software needs to support “block size”option to be used for the phone

upgrade.

•Freeware: tftpd32 with v3.35 works well, http://tftpd32.jounin.net/

HTTP server software can be used for SMT-i5230/5243 software upgrade

•Freeware: Mereo with v1.08 works well, http://www.ohloh.net/p/mereo

Note:

Need to point the server directory to the software version name. It should have the

sub folder called “ITP-SERIES”that contains the software files.

Example:

Point to the server directory to C:\Software\New IP phones\SMT-i5243\SMT-

i5243_V1.64_4_100405

Otros manuales para SMT-I3105

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teléfono IP de Samsung

Samsung

Samsung SMT-i6021 Manual de usuario

Samsung

Samsung SMT-5220 Manual de usuario

Samsung

Samsung GA68-60747A Manual de usuario

Samsung

Samsung WIP-500M Manual de usuario

Samsung

Samsung SMT-i5220S Manual de usuario

Samsung

Samsung SMT-i5343 Manual de usuario

Samsung

Samsung OfficeServ SOHO Manual de usuario

Samsung

Samsung OfficeServ ITP-5112L Manual de usuario

Samsung

Samsung SiPTel C01 Manual de usuario

Samsung

Samsung OfficeServ DS-5038S Manual de usuario

Samsung

Samsung OfficeServ 7400 Manual de usuario

Samsung

Samsung SMT-I3105 Manual de usuario

Samsung

Samsung OfficeServ ITP-5107S Manual de usuario

Samsung

Samsung SMT-i6000 Series Manual de usuario

Samsung

Samsung OfficeServ ITP-5121D Manual de usuario

Samsung

Samsung OfficeServ 7000's Manual de usuario

Samsung

Samsung SMT-5220 Manual de usuario

Samsung

Samsung OFFICESERV 100 Series Manual de usuario

Samsung

Samsung SMT-i5343 Manual de usuario

Samsung

Samsung SMT-5220 Manual de usuario

Samsung

Samsung SMT-I3105 Manual de usuario

Samsung

Samsung OfficeServ ITP-5112L Manual de usuario

Samsung

Samsung OfficeServ ITP-5112L Manual de usuario

Samsung

Samsung SMT-i6010 Manual de usuario

Manuales populares de Teléfono IP de otras marcas

Alcatel

Alcatel 4028 Manual de usuario

Polycom

Polycom Polycom VVX 600 Manual de usuario

Polycom

Polycom SoundPoint IP 450 Manual de usuario

Cisco

Cisco SPA-500 Series Manual de usuario

Polycom

Polycom SoundPoint IP 650 Manual de usuario

Proximus

Proximus Maestro 3016 IP Manual de usuario

Fanvil

Fanvil X4 Manual de usuario

Cisco

Cisco 7962 Manual de usuario

Snom

Snom 320 Manual de usuario

Yealink

Yealink Yealink SIP-T46G Manual de usuario

Avaya

Avaya 4625SW Manual de usuario

Yealink

Yealink SIP-T52S Manual de usuario

Nortel

Nortel 1140E Manual de usuario

Nexotek

Nexotek NT-P500 Manual de usuario

Avaya

Avaya Integral 5 R3.0 Manual de usuario

GE 28320EE2 - Dect 6.0 InfoLink 2 Manual de usuario

Avaya

Avaya 4600 Series Manual de servicio

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Manual de usuario