Samson 2357-1 Manual de servicio

Self-operated Pressure Regulators

Pressure Reducing Valve Type 2357-1/-6

Excess Pressure Valve Type 2357-2/-7

Edition April 2011

Mounting and

Operating Instructions

EB 2557 EN

Type 2357-1 Pressure

Reducing Valve

Type 2357-6 Pressure

Reducing Valve

Type 2357-2 Excess

Pressure Valve

Contents Page

1 Design and principle of operation . . . . . . . . . . . . . . . . . . . . . . 3

2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1 Mounting position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Shut-off valve and pressure gauge . . . . . . . . . . . . . . . . . . . . . . 5

3 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.1 Set point adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.2 Changing the set point range. . . . . . . . . . . . . . . . . . . . . . . . . 7

4 Dimensions in mm and weights . . . . . . . . . . . . . . . . . . . . . . . 9

2EB 2557 EN

Contents

General safety instructions

The regulators must be installed, started up and serviced by fully trained and

qualified personnel only, observing the accepted industry codes and

practices. Make sure employees or third persons are not exposed to any

danger.

All safety instructions and warnings in these instructions, particularly those

concerning installation, start-up and maintenance, must be observed.

For appropriate operation, make sure that the regulator is only used in

applications where the operating pressure and temperatures do not exceed

the operating values based on the sizing data submitted in the order.

Note that the manufacturer does not assume any responsibility for damage

caused by external forces or any other external factors.

Any hazards which could be caused in the regulator by the process medium

or operating pressure are to be prevented by means of appropriate

measures.

Proper shipping and appropriate storage are assumed.

The declaration of conformity issued for a valve bearing the CE marking

includes information on the applied conformity assessment procedure and

will be provided on request.

1 Design and principle of

operation

The pressure regulators maintain the pressure

at an adjusted set point and are particularly

suitable for cryogenic applications.

Type 2357-1 and Type 2357-6 Regulators

(globe valves)

The regulators act as pressure reducing

valves when the medium flows from port A to

port B. When no pressure is applied, the

valve is open.

The pressure downstream of the valve B is

transmitted to the operating diaphragm (3).

The resulting positioning force moves the

valve plug (2) in relation to the spring force,

which can be adjusted at the set point ad-

juster (10). The valve closes as the pressure

downstream of the valve B increases.

When the regulators are used as pressure

build-up regulators, the medium flows from

port B to port A. The pressure upstream of the

valve (B) is transmitted to the operating dia-

phragm (3). The valve closes as the pressure

upstream of the valve increases and opens as

the upstream pressure drops.

The pressure build-up regulator additionally

assumes the function of a safety valve,

depressurizing the pressurized valve when

the set point is exceeded by more than 5 bar.

When the pressure has overcome the force of

the springs located on top, the valve opens to

balance the pressures.

Type 2357-2 and Type 2357-7 Regulators

(angle valves)

The regulators functioning as excess pressure

valves, the medium always flows from port A

to port B. When no pressure is applied, the

valve is closed. The pressure at port A acts on

the operating diaphragm (3) in the valve

body. The resulting force opposes the adjust-

able spring force. As the pressure increases,

the valve opens until the set point is reached.

Regulators functioning as excess pressure

valves can optionally be equipped with a

non-return unit (12) which prevents the me-

dium from flowing back.

EC type examination

An EC type examination according to the

Pressure Equipment Directive 97/23/EC,

Module B has been performed on the regula-

tor versions for PN 50.

EB 2557 EN 3

Design and principle of operation

4EB 2557 EN

Design and principle of operation

13 13

Fig. 1 · Sectional drawings of Type 2357-1/-6 (left) and Type 2357-2/-7 (right)

7 Spring plate

8 Set point spring(s)

9 Lower section of body

10 Set point adjuster

11 Lock nut

12 Non-return unit

13 Strainer

1 Body

2 Plug

3 Operating diaphragm

4 Gasket

5 Diaphragm plate

6 Ball

2 Installation

2.1 Mounting position

The pressure regulator must be in-

stalled with the actuator housing

hanging downward.

Observe the following directions of flow:

4Ato Bin pressure reducing valves

4Bto Ain pressure build-up regulators

with safety function

4Ato Bin excess pressure valves

equipped with a non-return unit. Port B

must point upward.

The ports are marked.

Note: Make sure that any impurities carried

along by the process medium in the con-

nected pipelines do not impair the proper

functioning and especially the tight shut-off of

the regulator.

2.2 Shut-off valve and pressure

gauge

We recommend installing a hand-operated

shut-off valve both upstream and downstream

of the regulator to be able to shut down the

plant for cleaning and maintenance, and

when the plant is not used for longer periods

of time.

Install a pressure gauge both upstream and

downstream of the regulator to monitor the

pressures prevailing in the plant.

EB 2557 EN 5

Installation

11232

Fig. 2 · Typical installation

1 Shut-off valve

2 Pressure gauge

3 Pressure regulator

3 Operation

3.1 Set point adjustment

The pressure regulator is adjusted at the

factory to the set points listed in the table.

However, you can change them by turning

the set point adjuster (10).

When pressure gauges are installed in the

connected pipelines, you can adjust the de-

sired set point directly while monitoring the

corresponding pressure gauge.

When no pressure gauge is installed, use the

adjustment diagram to adjust the set point.

To increase the set point, turn the set point ad-

juster into the body, and to decrease the set

point, turn the set point adjuster out of the

body.

1. Undo the lock nut to allow the set point

adjuster to move freely.

2. Determine the difference between the

fixed set point (table below) and the re-

quired set point. Turn the set point ad-

juster the required amount of turns as

specified in the diagram.

Any subsequent change in set point can

be also be made by determining the re-

quired number of turns using the specifi-

cations listed in the table in “Set point

change per turn”.

3. Secure the setting with the lock nut.

6EB 2557 EN

Set point adjustment

Nominal pressure PN 40 PN 50

Set point range in bar 0.2 to 3 1 to 25 10 to 36 0.2 to 2.5 1 to 8 5 to 25 8 to 40

Set point

adjusted at the

factory to

approx. … bar

2357-1 1 12 20 1 3 12 25

2357-2 1 13 21 1 4 13 26

Set point change per turn

in bar 0.4 2.5 3.5 0.4 1 2.5 3.5

Table 1 · Set point adjustment

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 to 25 1 to 8

5 to 25

8 to 40

10 to 36

Fig. 3 · Adjustment diagram

Turns of the set point adjuster

Set point/Set point range in bar

3.2 Changing the set point range

The set point ranges adjusted by the manufac-

turer can be changed subsequently by ex-

changing the set point springs (8) and the op-

erating diaphragms (3).

In case of doubt, we recommend you to let

SAMSON perform this work for you.

The addresses of SAMSON AG, its subsidiar-

ies, representatives and service facilities

worldwide can be found on the Internet at

www.samson.de, in a SAMSON product cat-

alog or on the back of these mounting and

operating instructions.

CAUTION!

Always remove the regulator from the pipe

when performing any assembly work. Prior to

removing the regulator, relieve the pressure

as well as thaw and drain the corresponding

section of the plant.

1. Unscrew the lock nut (11). Completely re-

lieve the set point springs (8) of tension by

turning the set point adjuster (10) in a

counterclockwise direction.

2. Place the lower section of the body (9)

into a vise, but do not clamp it. Better: use

a box wrench with width across flats =

55 mm. Unscrew the body (1) using an

open-end wrench with width across flats

= 36 mm and remove all parts from the

lower section of the body. Be careful not

to damage the operating diaphragms

(3).

3. Install set point spring(s) for the required

set point range, the spring plates (7), the

ball (6) and the diaphragm plate (5) in

the lower section of the body.

4. Place the required number of dia-

phragms (see table of spare parts) onto

the diaphragm plate and replace the

PTFE gasket (4) of the valve body, if re-

quired.

5. Carefully place the body onto the lower

section of the body. Then screw the body

onto the lower section of the body using a

tightening torque of approx. 180 Nm for

PN 40 and approx. 250 Nm for PN 50.

EB 2557 EN 7

Operation

Note: Accessories and spare parts with order

numbers 1400-xxxxx are always delivered

"free from oil and grease for oxygen service."

8EB 2557 EN

Spare parts

Spare parts list Order no.

Pos. Spare part

PN 40 PN 50

Set point range in bar

1 to 25 10 to 36 1 to 8 5 to 25 8 to 40

3Number of diaphragms 33357

Set of accessories:

with 20 diaphragms

with 50 diaphragms 1400-7626

1400-7627 1400-7623

1400-7624

4Seals, set of accessories:

with 20 seals

with 50 seals 1400-7630

1400-7631 1400-7628

1400-7629

8Set point springs 1400-9747

1400-9747 1 to 25 bar

10 to 36 bar

1400-9383 1 to 8 bar

1400-7640 5 to 25 bar

1400-7305 8 to 40 bar

12 Non-return unit

for Type 2357-2 1400-5129 (15 mm) or 1400-5139 (16 mm)

13 Strainer 1400-5136 (270 x 10-6 m mesh size) or

1400-5126 (50 x 10-6 m mesh size)

Connecting parts:

Soldering nipple with

connection nut

1400-5133 (1 x Æ15)

1400-5134 (2 x Æ15)

1400-5138 (1 x Æ16)

1400-5137 (2 x Æ16)

Table 2 · Spare parts list with order numbers

4 Dimensions in mm and weights

EB 2557 EN 9

Dimensions in mm and weights

150

110

51(35)

140 (95)

Ø16

140

Ø15

140

118

Ø15

140 (95)

Ø16

Ø15

Fig. 4 · Dimensions

Type 2357-7

Weight approx. 2.5 kg

Values in parentheses for PN 40 version

Type 2357-6

Weight approx. 3.0 kg

Type 2357-1

Weight approx. 2.0 (0.9) kg Type 2357-2

Weight approx. 1.7 (0.8) kg

10 EB 2557 EN

Otros manuales para 2357-1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Samson

Samson

Samson BR 14t - LTR 43 Manual de servicio

Samson

Samson 580 Manual de usuario

Samson

Samson 2412 Series Manual de servicio

Samson

Samson 3222 Series Manual de servicio

Samson

Samson 3510-1 Manual de servicio

Samson

Samson 3525 Manual de servicio

Samson

Samson BR 20a Manual de servicio

Samson

Samson 3331/BR 31a Manual de servicio

Samson

Samson 3349 Manual de servicio

Samson

Samson 3253 Guía de configuración

Samson

Samson 2488/5 Series Manual de servicio

Samson

Samson EB LTR 43 Manual de servicio

Samson

Samson 3969 Manual de servicio

Samson

Samson 2408 Manual de servicio

Samson

Samson 2405 Series Manual de servicio

Samson

Samson 2333 series Manual de servicio

Samson

Samson 2417 Series Manual de servicio

Samson

Samson 44-7 Manual de servicio

Samson

Samson 3271 Manual de servicio

Samson

Samson 3241-1-Gas Manual de servicio

Samson

Samson BR 26l Manual de usuario

Samson

Samson 44-2 Manual de servicio

Samson

Samson 3349 Manual de servicio

Samson

Samson 3349 Manual de servicio

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario