SAFE-TECH AJ Series Manual de usuario
Scan for Installation Video
SAFE-TECH © -2022 |All Right Reserved
Quick Start Guide –for AJ-Series Interlinked alarms
SAFE-TECH V9
*Please pair all devices before installing them
LEDLights
Interlinked Carbon Monoxide Alarm
AJ-833si
Control/Test Button
C
Front View
Back View (Without Back Plate)
On / Off Switch (Latching Push Switch)
Interlinked Remote Controller
AJ-R1062
Control / Test Button
LEDLight
Front View Back View
Remove Plastic Tag
to Activate Device D
Hush Button
Test Button
Heat Sensor & LED Light
Interlinked Heat Alar m
AJ-718i
Back View (Without Back Plate)
A
On /Off Switch
Front View
Interlinked Smoke Alarm
AJ-762i / AJ-763i
Control Button
LED Light
Back View (Without Back Plate)
B
On /Off Switch
Front View
Text here
Stop Pairing Mode: After pairing all the devices, go back to the master device and press the test/control button
once to finish pairing.
Ensure alarms are switched on before operation.
Caution : Loud Beeps
Clear Pairing: First, remove pairing on all devices. Press and hold the control/test button and lift your finger
after you see the Green light has flashed four times.
*For adding additional devices to an existing group, you only have to do this step for the new devices
SAFE-TECH V9
*Please pair all devices before installing them
Activate Pairing Mode: This Step is Only for the master device. You can choose any one device to be the master.
*NOTE, the pairing mode on the main deviceonly stays active for 60 seconds, if the main device’s light
stops blinking, repeat the process, go back into pairing mode on main device and pair the rest of the devices to it.
If you need to end the pairing mode, press the button once at your main device.
Interlinking: To link all the devices to the master device, press and hold the control/test button and lift your finger
after the second green light.
Step 2
Step 3
Step 4
Step 5
Step 1
To activate the pairing mode, Press and Hold the control/test button and lift your finger after the green light has
flashed three times.
When you lift your finger after the third green light, you will see a red light flashing, indicating that the pairing mode
is Activated.
Do the same for all the other detectors that you want to interlink. For the remote control, press and hold the test
button till you see the red light flash two times and release your finger right after the second red light.
*If you are pairing additional devices to the group, you only need to use one of the devices already in
the group to link the new device(s) to the existing group.
Pressing the button once will stop the red flashing light.
Testing: Press the button once on any of the alarms, and they should all go off together.
If a detector doesn’t go off with the others, the interlinking has not been successful. So, Activate the pairing mode
again on the master device (Step 2) and add the unpaired device to it (Step 3). You can follow this process for any
additional device you want to add to the interlinked system later.
How to activate different modes
Reset Pairing
Press and hold till 4 Green Lights have flashed
Activate Pairing Mode (Master only)
Press and hold till 3 Green Lights have flashed
Adding To Master
Press and hold till 2 Green Lights have flashed
How to interlink the devices
Step 1
Remove pairing from all the devices
(4 Green Lights)
Step 2
Choose one device to be the Master and activate Pairing Mode
(3 Green Lights)
Step 3
Link all other devices to the master device
(2 Green Lights)
Step 4
Close the pairing mode by pressing the master device once
Scan for Installation Video
Please read through all the instructions before starting the interlink setup
Master device: Follow all the steps 1, 2, 3 and 4
All other devices: Only follow steps 1 and 3
SAFE-TECH © -2022 |All Right Reserved
Este manual sirve para los siguientes modelos
5
Otros manuales de Sistema de seguridad de SAFE-TECH
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario