SAFE HOME JPT3813W Manual de usuario
UK - Users Manual 2
DK - Brugsanvisning 19
SE - Bruksanvisning 37
NO - Bruksanvisning 55
Wireless IP Network Camera
IP601W Outdoor
JPT3813W
JPT3815 W
www.safehome.dk
2
Table of Contents
0. Before you start 3
Package Contents 3
System Requirements 3
System architecture 3
Internet 3
1. Product 4
Front 4
Back 4
Functions 4
2. Hardware installation and configuration 5
Prepare the camera 5
Installing software 5
3. Log into the camera from the browser 8
4. Control panel 9
5. Administrators Menu 10
Device Info 10
Alias Settings 10
Date & Time Settings 10
User Settings 10
Multi-Device Settings 10
Basic Network Settings 11
Wireless Lan Settings 11
ADSL Settings 11
UPnP Settings 12
Setting up Email 12
FTP Service Settings 13
Alarm Service Settings 14
PTZ Settings (Pan Tilt Zoom) 15
Decoder Settings 15
Device Firmware Upgrade 15
Backup & Restore Settings 15
Reboot Device 15
Log 15
Back 15
6. Accessing the camera from the Internet
outside your home
Static IP address 16
Dynamic IP address 17
DDNS Service Settings 17
7. FAQ - Troubleshooting 18
Reset 18
8. Disclaimer 18
www.safehome.dk
3
0. Before you start
Package Contents
• Wireless camera
• WI-FI Antenna
• Power Supply
• Manual
• CD with driver for the camera and IP camera program
• Mounting Brackets
Immediately contact the dealer if content is missing.
System Requirements
• 10/100 Mbps Network Card with min. 64M memory
• CD-ROM drive
• CPU: 2.06 GHz or more
• Windows 2000/XP/Vista or 7
• Web Browser: Internet Explorer (6.0 or newer), Firefox and Safari (does not support all
features)
• Wireless Router or Access Point (If you want wireless transmission. Otherwise the cable
router)
• DHCP Server (is usually built into the router)
System architecture
Internet
Wireless Internet Camera
with Web-server
JPT3813W
JPT3815W
or
IP601W Outdoor
Wireless router
or acces point
www.safehome.dk
4
1. Product
Front
Linse CMOS sensor. Can be
rotated manually to adjust the
sharpness of the image
(Only JPT3813W and JPT3815W)
Infrared LED light
Network indicator LED
Built-in microphone
Back
LAN: RJ-45/10-100 Base T
Antenna Connector
For Power Supply
Audio Output (Only
JPT3813W and JPT3815W)
Functions
• Powerful high-speed video protocol processor
• High-sensitivity 1/4“ CMOS Sensor
• 300K Pixels - color
• For day and night use. IR night light gives a range of up to 8 m for JPT3813W/
JPT3815W and up to 50 m for IP601W (sensor range up to 20 m for IP601W)
• Optimized MJPEG video compression (.avi)
• Multi-level user setup and access with password
• Built-in Web server for use with Internet Explorer, Firefox and Safari
• Supports wireless network (Wi-Fi/802.11/b/g)
• Supports Dynamic IP (DDNS) and UPnP LAN and Internet (ADSL, cable modem)
• Built-in motion sensor
• Oneway audio surviellance with microphone (Only JPT3813W and JPT3815W)
• Supports image snapshot
• Supports multiple network protocols:
HTTP/TCP/IP/UDP/STMP/DDNS/SNTP/DHCP/FTP
• Supports remote system update
• Can be used and operated with multiple Mobile Apps for e.g. iPhone / IPAD or Android
• Contact SafeHome at [email protected] for a few useable applications
www.safehome.dk
5
2. Hardware installation and configuration
Prepare the camera
1. Connect the router / switch and camera with a RJ-45 network cable.
2. Connect the power adapter to the camera and then to a power outlet (use only the sup-
plied power adapter. Others can damage the camera)
3. The camera uses about 30 seconds to start before it can be seen by the software you
must install on your computer.
4. The camera head will rotate (on pan/tilt models), and stop in position. LED lights for the
network will glow steadily if the cable is connected correctly.
Installing software
The supplied software must be installed on a computer in the network before the camera
can be set up.
1. Insert the CD into the CD-ROM drive
2. If the installer does not start, open the CD drive in Explorer and double click on
IPCamSetup.exe. If the CD is un-readable, you can download the software from www.
safehome.dk
3. Click “Install Software”
4. Click “Next” to install
www.safehome.dk
6
5. Click “Next” to continue installation
6. Click “Close” after you select “Yes I want to restart my computer now” to complete
installation
7. After restart a new icon to open the tool to be used conguring the camera, is found on
the computers desktop.
When the camera is turned on, and properly connected to the router/switch, click on the
“IP Camera Tool” and a small window will open.
The program will automatically check for IP Servers with camera on the network, and
show them on the list.
www.safehome.dk
7
When the program searches, three things may occur:
1. There are no cameras found within a minute. Result eld will show “no found IP Serv-
ers” and the program shuts down.
2. IP camera is installed with another “Subnet Mask” than registered on the computer
you are using. A text box opens, and you can
double click to correct it. Then this box to the
right appears: If you know the system’s network
conguration, you can edit manually in the elds
or you can try to mark in the top eld “Obtain
IP from DHCP server” and then click OK, the
program will attempt to x the problem by issuing
valid IP and subnet mask.
3. IP Camera/cameras found and
listed. Doubleclick on the camera
you want to acces thru your web
browser. The browser will open
and display a login window. Later
you can acces the IP camera
by entering the IP address the
camera has been assigned, for
example.:
http://192.168.1.239:81 (number
after “:” is the Http port the camera is set up to)
The icon for “IP Camera Tool” will still be on the desktop and can now be used for ac-
cess.
www.safehome.dk
8
3. Log into the camera from the browser
Login from IP Camera Tool or by entering the camera IP address directly into the browser
You get to a window where you choose which web-browser you use.
Once you have chosen browser, enter the username and password, and you get into the
camera’s control panel.
By default the username is admin and there should not be written anything in the pass-
word field.
You can change the username and password from the administration part of the control
panel.
Read more about the setup and options under “Administrators Menu.
www.safehome.dk
9
4. Control panel
Depending on your camera model, there may be different control layouts on the page
where you see the video stream. If you log in as “Administrator”, you can use all the op-
tions in the control panel.
If you log in as “Guest” (see below under User Settings how you can grant users access
to different levels), you only have the opportunities in the control panel’s left side.
As “Operator” you have access to options in both side.
Both “Guest” and “Operator” can tap into the administrative part, but can not see the set-
tings or change anything.
1. When multiple cameras are connected, you can select between the cameras. If the
motion sensor is activated, the will be a ashing red dot on the camera icon when there
is an alarm.
2. When multiple cameras are connected you can choose whether there should be from 1
up to 4 or up to 9 cameras on screen simultaneously.
3. Click if there should be time and date on recordings.
4. Show date and time on screen. You may choose color.
5. Audio Buffer - the unit is second.
6. Power on and off for display, if you press the button with a camera, it will take a picture
that opens in a new window. The image can be stored on your computer by right click-
ing on it and choose “Save As”.
7. Turn speakerphone on or off. Turn microphone on and off or shoot video. Video are
recorded in AVI format.
8. Area for maneuvering the camera (only if the camera is designed for pan/tilt).
9. Vertical or horizontal ip of the image.
10. Setting the picture quality, brightness and contrast.
1
2
3
4
5
6
7
8
9
10
www.safehome.dk
10
5. Administrators Menu
Device Info
When you open the administrator menu, a menu opens on the
left side.
On the opening page, you nd the device’s MAC address
(Device ID), version of rmware and web server version, and
status of other settings you have chosen.
Alias Settings
Here you choose a name for the camera. The name will ap-
pear on the image if it is selected in the Control Panel menu.
If you have multiple cameras installed, it may be practical with
unique names for each device instance. “Front door”, “Living
Room” or “Children’s Room.”
Date & Time Settings
You can choose to set it manually, you can allow the device to synchronize with an NTP
Server or with the PC you use to control the camera.
User Settings
You can create up to 8 user accounts for the camera.
For each account you specify the username and password and access level (Group).
During the access level you have three options:
Guest: Can only see the picture
Operator: Can control the camera movement, and can also provide simple parameters for
the image.
Administrator: Can control everything, and adjust all the parameters for the camera.
Multi-Device Settings
You get a list of the cameras you have installed in the network. To add an extra camera,
click on “The 2nd Device”. Click the camera you want to add to the list of the top, and the
first three fields will be filled in automatically.
Enter the username and password for the camera and click “Add”.
To remove a camera from the list, click on “Remove”.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Cámara de seguridad de SAFE HOME
