Safe Fleet PRIME DESIGN HRX-009-E-RETRO Manual de usuario

PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118

Toll Free: 1.8.PRIME.RACK ▪ Fax: 651-552-1799 ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

2

1

7

8

3

5

6

4

9

10

2

11

HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

CONTENTS OVERVIEW

1—Rear Crossbar Assembly.................................. (Qty 1)

2—Front Crossbar Assembly ................................. (Qty 1)

3—Rear Drive Shaft .............................................. (Qty 1)

Left Hand, A Version, 50.00”

4—HHR Handle Assembly .................................... (Qty 1)

35.00”

5—Connecting Bar ................................................ (Qty 1)

4.00’

6—Front Drive Shaft ............................................. (Qty 1)

B Version, 35.75”

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

3

HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

9—Z Post ............................................................... (Qty 1)

Adjustment, 7.25”

10—L Post ................................................................ (Qty 1)

G1, Square Cap, 9.25” w/Hardware

7—Hydraulic Cylinder ............................................ (Qty 1)

8—BLT-6811-M8.................................................... (Qty 1)

Cylinder Hex Head Assembly, M8 x 110MM

12—HKT-8163 (Not called out in Overview)........ (Qty 1)

11—USQSG-Ergorack ............................................ (Qty 1)

Quick Start Guide, Rotation

" Flat Washer (10X)

Anti-Seize (1X)

Lubricant (1X)

Clevis Pin (1X)

Cotter Pin (1X)

M8 x 50MM (4X) ⅜" x 2.25" (2X)

1.00" Sealing

Stickers (16X)

M8 Lock Nut (5X) ⅜" Lock Nut (2X) ⅜" Flat Washer (4X)

M8 x 25MM (1X)

M8 Lock Nut (1X) " Flat Washer (1X)

M8 x 65MM (1X)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

4

HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION

1

2/5/12

4

6

7

9

3

8

10

3

11

Bushing,

1.75”L

Bushing,

1.25”L

Nylon

Washer

Flanges face

each other

Flange

1.1

Torque to 55 in-lbs

1.2

REAR CROSSBAR ROTATION

NOTE: Ladder Rack is shown for illustrative

purposes only, and is not included with this

Slide Rotation Retrot Kit.

This Slide Rotation Retrot Kit contains only

the parts needed to repair, replace, or retrot

one Slide Rotation.

LEFT SIDE ASSEMBLY SEQUENCE

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

5

HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION

2.1

Torque to 18 in-lbs

2.2

CYLINDER HARDWARE

NOTE: Flow Control Screw

faces toward vehicle rear

NOTE: Ensure Cylinder

Bushing is fully seated

against Crossbar

FRONT CROSSBAR ROTATION

3.1 Torque to 55 in-lbs

3.3

3.2 Press the small .75” (A) round Caps

into the Crossbar holes as shown.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

6

HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION

REAR DRIVE SHAFT

4.1

4.2

4.3

Torque to

90 in-lbs

4.4

CYLINDER HARDWARE

5.1

5.2

CONNECTING BAR

6.1

6.2

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

7

HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION

FRONT DRIVE SHAFT

Torque to

90 in-lbs

7.1

7.2

7.3

7.4

CONNECTING BAR FASTENERS

8

Z POST

SEE QUICK START GUIDE FOR ADJUSTMENTS

Torque to 90 in-lbs

9.1

9.2

L POST

10

Torque to 90 in-lbs

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

8

HRX-009-E-RETRO ASSEMBLY INSTRUCTIONS–LEFT SIDE ROTATION

USAM-HRX009ERETRO-US01 Rev-B 0218

DRIVE SHAFT SEALING

Apply Silicone Sealant

to Connecting Bar ends

11.2

11.1

Adjust the Cylinder Flow

Control Screw to allow

approximately 3 seconds

time for the ladder to glide

down when operating the

loaded Ladder Rack.

12

CYLINDER ADJUSTMENT

Safe Fleet PRIME DESIGN HRX-009-E-RETRO Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas