S.R.Smith EDGE 6 Manual de programación

ASSEMBLY & INSTALLATION INSTRUCTIONS

EDGE DIVING SYSTEM

BK-EDGE INSTALL |0919

S.R.Smith, LLC

800.824.4387

srsmith.com

ATTENTION! THESE INSTRUCTIONS MUST

REMAIN WITH PLATFORM OWNER

**PROFESSIONAL INSTALLATION RECOMMENDED**

WARNING:

IMPORTANT INSTALLATION

INFORMATION

The installation of this product should be done only by a licensed and professional installer.

Installation should be done strictly in conformance with all local building codes, electrical

codes and other building and safety laws and regulations. Among other things, that your

installer should carefully analyze the need to bond the product to prevent an electrical

hazard. Failure to properly install this product could result in a dangerous condition, including but

not limited to electrical and or structural hazards. S.R.Smith. disclaims all liability arising from

the installation and the user assumes all risk associated with the installation.

For Technical Support or Assistance, Contact Customer Service at:

Canby, Oregon | 800.824.4387

srsmith.com

For warranty information:

srsmith.com/warranty

To obtain complete copies of the ANSI/APSP/ICC-5 2011 Standard for Residential

In-ground Pools or to obtain copies of the “Plan Your Dive, Steer Up” or “The Sensible

Way to Enjoy Your In-ground Swimming Pool” contact:

The Association of Pool & Spa Professionals (APSP)

2111 Eisenhower Ave.

Alexandria, VA 22314

(703) 838-0083

www.theapsp.org

WARNING

srsmith.com

INSTALLATION MANUAL EDGE DIVING SYSTEM

1srsmith.com

TABLE OF CONTENTS:

Safety First ............................................................................................................................................2-3

Important Notices to the Installer...............................................................................................4

Minimum Diving Water Envelope Information ...................................................................5

Edge Fiberglass Base Placement....................................................................................................6

Edge Diving Board Dimensions ....................................................................................................7

Edge Jig Information.............................................................................................................................7

Installation Instructions ..................................................................................................................7-8

Edge Fiberglass Base Exploded View & Parts List..............................................................9

Article 5 Extracted from ANSI/APSP/ICC-5 2011................................................. 10-15

INSTALLATION MANUAL EDGE DIVING SYSTEM

2srsmith.com

This S.R.Smith diving board and stand shall be installed only by a professional swimming pool contractor or with the direct

supervision of a licensed professional, engineer or architect. Diving boards may be installed only on residential

in-ground swimming pools properly designed for their use.

Diving boards that are improperly installed can be very dangerous to the user resulting in possible serious head and/

or spinal column injury, including the paralysis or death of the user.

It is very important that this diving board and/or stand be installed only on a pool that is built in strict accordance

with the American National Standard for Residential In-ground Swimming Pools (ANSI/APSP/ICC-5 2011) and

in strict accordance with the included S.R.SMITH RESIDENTIAL POOL SPECIFICATIONS TABLE 2. Under no

circumstances can this diving board and/or stand be installed on any above ground or on-ground swimming pool.

In addition to the above standard and referenced table, these installation instructions provided by S.R.Smith must

be diligently followed.

It is also important that any and all warnings provided with the diving board be strictly adhered to and posted in a

conspicuous location. If not provided or they are misplaced, please purchase warning signs from your pool contractor

or professional pool supply store and post them in a location that the users of the diving board can clearly see.

DIVING TIPS: Even the safest equipment must be used properly. S.R.Smith promotes safe diving by offering these tips on the

proper use of your diving board: always dive into water that meets depth requirements, with arms extended; be aware of the

bottom and the walls of the pool; avoid collisions with pool toys and floats; and instruct your pool users to always “steer up”.

When you begin your dive you must get ready to steer up. As you enter the water, your arms must be extended over your

head, hands flat aiming up. Hold your head and arch your back.

FOR RESIDENTIAL IN-GROUND SWIMMING POOL USE ONLY

NO COMMERCIAL, PUBLIC OR SEMI-PUBLIC USE IS ALLOWED

ONLY ONE PERSON ON THE DIVING BOARD AT ONE TIME

MAXIMUM WEIGHT = 300 LBS

PLAN YOUR DIVE

BACK ARCHED

ARMS EXTENDED

HEAD AND HANDS UP

HOLD DIVING FORM

STEER UP FOR A SAFE DIVE.

PLAN YOUR DIVE, STEER UP

SAFETY FIRST!

WARNING

INSTALLATION MANUAL EDGE DIVING SYSTEM

3srsmith.com

THE EDGE DIVING SYSTEM IS A JUMP BOARD

“A pool is the safest place to swim and a diving board installed in compliance with manufacturers instructions and

the ANSI/APSP/ICC-5 2011 Standard for In-ground Residential Pools is the safest place to dive from. To ensure

that you and your family and guests are able to safely enjoy your diving board for many years, it is critical that you

follow the following instructions.”

1. Know the shape and depth of the pool before you dive.

2. Make sure that all family members and guests are

familiar with these instructions before they use your

pool and diving board.

3. Make sure that the diving board has been installed in

compliance with the Assembly and Installation Instructions

and with the ANSI/APSP/ ICC-5 2011 Standard for

In-ground Residential Pools. This includes the shape and

depth of the pool as well as the height of the diving

board.

4. Enter feet first the first time.

5. Plan your path to be sure you avoid any other

swimmers, or objects in or under the water, such as

floats, tires, toys etc.

6. Keep your head up, arms up and fully extended and

steer up with your hands.

7. Practice carefully before you dive headfirst.

8. Become familiar with the diving board and its spring

before diving headfirst

9. Dive straight ahead, not to the side of the board or

pool.

10. Dive from the diving board only.

11. Make sure that children and non-swimmers are

supervised at all times.

12. Always remember that when you dive you must steer

up.

13. Inspect your diving board, base and stand on a regular

basis (at least twice a year) and keep them in proper

repair.

14. Contact your dealer, installer or S.R.Smith (800-737-

5386) with any questions or concerns about the safe use

of your diving board.

DON’T

1. Don’t drink and dive.

2. Don’t install this or any diving board on an above

ground pool or dive into an above ground pool from

any surface.

3. Never install any S.R.Smith diving board on a variable

fulcrum dive stand.

4. Don’t dive into a pool from anyplace not specifically

designated for diving. Never dive into the shallow

portion of any pool.

5. Don’t dive across the width of the pool or to the sides

of the pool.

6. Don’t Run and dive.

7. Don’t engage in horseplay in or around the diving board or

pool.

8. Don’t use your diving board as a trampoline.

9. Don’t do a back dive. Backyard pools are not built for

that type of activity.

10. Don’t try fancy dives. Keep the dives simple.

11. Don’t dive into or through objects or toys such as inner

tubes.

12. Don’t swim or dive alone.

13. Don’t use a diving board or stand or base that is rusted

or worn out or in poor repair.

INTENDED USE

INSTRUCTIONS

WARNING

INSTALLATION MANUAL EDGE DIVING SYSTEM

4srsmith.com

The specifications found on page 5 of this manual represent the minimum water envelope required by S.R.Smith and

by the ANSI/APSP/ICC-5 2011 Standard for residential Inground Swimming Pools. Each of these dimensions must be

met or exceeded. Installation of a diving board of any type on a pool that does not meet or exceed each of the min-

imum specifications as provided on page 5 including but not limited to the slope requirement, is in direct violation of this

manufacturer’s instructions and the 2011 Standard, and can result in serious injury or death.

Installation of this Edge Fiberglass Stand and Edge Diving Board is limited to Residential Inground Pools ONLY.

CHECK YOUR LOCAL ELECTRICAL CODE FOR BONDING REQUIREMENTS.

There is only one Edge Fiberglass Stand and only one Edge Composite Spring Set. You can install either a 6’ or 8’

Edge diving board on this assembly in accordance with Table 1- Minimum Water Envelope ANSI/APSP/ICC-5 2011

and Table 2- S.R.Smith Residential Pool Minimum Specifications on page 5. Installing any diving board greater than 8’

on any Edge Stand is strictly prohibited.

USE ANTI-SEIZE ON ALL HARDWARE.

S.R.Smith Edge Diving Boards are designed for use only with the Edge Diving Stand and Edge Composite Spring Set.

Edge components are only compatible with other Edge components.

Comply with local government regulations for Residential Inground Swimming Pools if they exceed the ANSI/APSP/

ICC-5 2011 Standard for Residential Inground Swimming Pools.

DO NOT USE ANY EDGE DIVING COMPONENTS WITH NON-EDGE COMPONENTS!

Read carefully pages 12–15 of this installation manual which contain portions of the ANSI/APSP/ICC-5 2011 Standard

for Residential Inground Swimming Pools, ensure that you understand the minimum required diving water envelope in

Figure 3 and Table 1 provided in the ANSI/APSP/ICC-5 2011 Standard.

NOTE: The installation of this Edge Diving Stand/Edge Diving Board is not complete until you, the installer have measured

the pool as well as the diving board’s overhang, height above water and the fulcrum distance to ensure they meet the

S.R.Smith’s Residential Pool Minimum Specifications and the ANSI/APSP/ICC-5 2011 Standard for Residential Inground

Swimming Pools. In addition; the installation of this diving board is not complete until you the installer have delivered to your

customer and reviewed with your customer the “Owners Manual” as well as the “Plan Your Dive Steer-Up” brochure.

THE EDGE DIVING SYSTEM IS A JUMP BOARD

ONLY ONE PERSON AT A TIME ON THE DIVING BOARD,

WITH A MAXIMUM WEIGHT LIMIT OF 300 LBS.

IMPORTANT NOTICES

TO THE INSTALLER

INSTALLATION MANUAL EDGE DIVING SYSTEM

5srsmith.com

MINIMUM DIVING WATER ENVELOPE:

NOTE: DRAWINGS ARE NOT TO SCALE.

A B C D A B C D WA AB BC CD* DE WE

I 6’-0” 7’-6” 5’-0” 2’-9” 10’-0” 12’-0” 10’-0” 8’-0” 1’-6” 7’-0” 7’-6” VARIES 6’-0” 28’-9”

II 6’-0” 7’-6” 5’-0” 2’-9” 12’-0” 15’-0” 12’-0” 8’-0” 1’-6” 7’-0” 7’-6” VARIES 6’-0” 28’-9”

III 6’-10” 8’-0” 5’-0” 2’-9” 12’-0” 15’-0” 12’-0” 8’-0” 2’-0” 7’-6” 9’-0” VARIES 6’-0” 31’-3”

IV 7’-8” 8’-6” 5’-0” 2’-9” 15’-0” 18’-0” 15’-0” 9’-0” 2’-6” 8’-0” 10’-6” VARIES 6’-0” 33’-9”

V 8’-6” 9’-0” 5’-0” 2’-9” 15’-0” 18’-0” 15’-0” 9’-0” 3’-0” 9’-0” 12’-0” VARIES 6’-0” 36’-9”

POOL

TYPE

MINIMUM DEPTHS

AT POINT MINIMUM WIDTHS

AT POINT MINIMUM LENGTHS

BETWEEN POINTS

TABLE 1 - MINIMUM WATER ENVELOPE (ANSI/APSP/ICC-5 2011)

DIVING BOARD LENGTH HOW** F G H J K L M N

I 6’ DB / 6’ JB / 7’ T7 20” 2’-9” 5’-0” 4’-0” 7’-2.5” 7’-6” 6’-0” 3’-9” 2’-1.5” 12’

II 8’ DB / 6’ JB / 7’ T7 20” 2’-9” 3’-10” 4’-2” 7’-2.5” 7’-6” 6’-8” 3’-9” 2’-1.5” 12’

III 10’ DB / 8’ JB / 7’ T7 26” 2’-9” 4’-4.75” 4’-4.5” 7’-5.5” 8’-0” 6’-7” 3’-11.5” 1’-7.5” 13’

IV 10’ DB / 8’ JB / 7’ T7 30” 2’-9” 5’-10.5” 3’-10” 7’-8” 8’-6” 8’-3” 5’-7” 2’-7” 13’

V 12’ DB / 8’ JB / 7’ T7 40” 2’-9” 6’-2” 3’-11.5” 7’-9.5” 9’-0” 8’-2.5” 5’-9” 2’-7” 14’

POOL

TYPE

MAX. DIVING BOARD LENGTH

MAX. HEIGHT

OVER WATER

AT POINT A

CROSS SECTIONAL

DIMENSIONS AT

POINT A

CROSS SECTIONAL DIMENSIONS AT POINT B

TABLE 2 - S.R.SMITH RESIDENTIAL POOL MINIMUM SPECIFICATIONS

MIN. HEAD

ROOM ABOVE

DIVING

SURFACES

*Min. length between points CD may vary based upon water depth at point D and the slope between points C & D

ABBREVIATIONS: DB=Diving Board; JB=Jump Board; **HOW=Height Over Water

DIVING EQUIPMENT

TIP OF BOARD

ABOVE POINT A

DIVING EQUIPMENT

DIVINGEQUIPMENT PROHIBITED

INSTALLATION MANUAL EDGE DIVING SYSTEM

6srsmith.com

TABLE 3 – PLACEMENT CHART

ADDITIONALLY REFER TO: ANSI/APSP/ICC-5 2011 American National Standard for Residential Inground Swimming Pools and

to page 5 for S.R.Smith Residential Inground Pool Minimum Specifications.

NOTE: WHEN COPING IS USED, DO NOT SET FRONT JIG BOLTS CLOSER THAN 3” FROM THE BACK EDGE OF THE COPING.

* IMPORTANT: The distance for setting the front jig bolt (S) from the water’s edge is valid only if the minimum water depth is maintained at the tip of the board noted

as point “A” in ANSI/APSP/ICC-5 2011 American National Standard for Residential Inground Swimming Pools. If minimum water depth is not maintained the distance

(S) must be adjusted accordingly.

** “WA” dimension is valid only in conjunction with the minimum depth at point “A” for type pool in accordance with ANSI/APSP/ICC-5 2011 American National

Standard for Residential Inground Swimming Pools.

IMPORTANT:

THESE DIMENSIONS ARE

ACCURATE ONLY FOR

VERTICAL POOL WALLS,

TYPICALLY GUNITE

CONSTRUCTION, WITH

LESS THAN A 3’ RADIUS

TO THE POOL FLOOR.

DUE TO THE VARYING

SIZES OF OTHER POOLS,

TYPICALLY VINYL LINER

CONSTRUCTION, PLEASE

CONTACT CUSTOMER

SERVICE FOR PROPER JIG

PLACEMENT.

1-800-737-5386

EDGE

DIVING

SYSTEM

PART #

NOMINAL

BOARD

LENGTH

ANSI/

NSPI-5

POOL

TYPE

DISTANCE FROM

WATER’S EDGE TO

FORWARD JIG BOLT

(S)

DISTANCE FROM

END OF BOARD TO

FORWARD JIG BOLT

MAX HEIGHT

OF BOARD

ABOVE

WATER

(HOW)

EDGE-BASE

6’ I 31.5” 49.5” 18” 20”

EDGE-BASE

6’ II 31.5” 49.5” 18” 20”

EDGE-BASE

6’ III 25.5” 49.5” 24” 26”

EDGE-BASE

6’ IV 19.5” 49.5” 30” 30”

EDGE-BASE

6’ V 13.5” 49.5” 36” 40”

EDGE-BASE

8’ I

EDGE-BASE

8’ II

EDGE-BASE

8’ III 44.25” 68.25” 24” 26”

EDGE-BASE

8’ IV 38.25” 68.25” 30” 30”

EDGE-BASE

8’ V 32.25” 68.25” 36” 40”

MIN.

OVERHANG

(WA)

NOT ALLOWED

FIG. A – EDGE FIBERGLASS BASE PLACEMENT SPECIFICATIONS:

S.R.SMITH CANNOT GUARANTEE CUSTOMER’S CONCRETE OR THICKNESS

NOTE: READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE ATTEMPTING THE INSTALLATION.

INSTALLATION INSTRUCTIONS

INSTALLATION MANUAL EDGE DIVING SYSTEM

7srsmith.com

FIG. B – EDGE DIVING BOARD

TABLE 4 – BOARD DIMENSIONS AND FULCRUM SETTINGS

Model # Nominal Length A B C D F DIA.

EDGE 6 6’ 70.25” 17.25” 6.31” 4.00” 42.50” .625”

EDGE 8 8’ 94.00” 17.25” 6.31” 9.00” 42.50” .625”

Jig Type A B C BOLT

Edge Fiberglass 12” 12” 6” 1/2” X 6”

FIG. C – EDGE JIG

INSTALLATION INSTRUCTIONS: Edge Diving System WITHOUT Board Fall Unit

Be sure the concrete deck surrounding the anchor jig complies with the minimum dimensions as shown in Figure A on

pages 6.

CHECK YOUR LOCAL ELECTRICAL CODE FOR BONDING REQUIREMENTS.

Read and understand the ANSI/APSP/ICC-5 2011 American National Standard for Residential Inground swimming Pools

and Table 1 and Table 2 on page 5 before you install Edge Fiberglass Stand and/or Edge Diving Board.

The Edge four-bolt jig should be set in accordance with Table 3 on page 6. The diving board must be placed on the deep

end of the pool on centerline.

The tip of the diving board must be positioned directly over Pt. A as shown on page 5 and according to the ANSI/APSP/

ICC-5 2011 Standard and S.R.Smith’s Residential Pool Minimum Specifications.

Make sure the jig anchor bolts project out of the concrete deck 1-1/2” for the Edge Stand with ample concrete depth

below the jig in accordance with Figure A on page 6. Do not install the Edge Diving System if the deck does not meet

the minimum requirements.

TABLE 5 – JIG DIMENSIONS

INSTALLATION MANUAL EDGE DIVING SYSTEM

8srsmith.com

When finishing the deck surface, maintain a level deck where the jig bolts project out so the dive stand makes uniform

contact with the deck surface. Allow the cement to fully cure before bolting the dive stand to the jig bolts.

Before bolting the dive stand to the jig bolts, chisel away any excess concrete that may have built up around the jig bolts

then remove the protective yellow rubber bolt caps.

The top surface of the diving board from the deck end to the

tip end shall be level or have an upward slope of 5/8” per foot

maximum. Elevation difference shall not exceed 3-3/4” for a 6’

board or 5” for a 8’ board. There shall be no downward slope

towards the water. The slope shall be measured using a level as

shown in the graphic to the left.

ONLY ONE PERSON ON THE JUMP BOARD AT A TIME, WITH A MAXIMUM WEIGHT OF 300 LBS.

FIG. D

Edge Springs

FIG. E

Edge Fiberglass Base

STEP ONE:

Lay the Edge board upside down on the box it was shipped in. Attach the Edge Springs to the board with hardware kit

EDGE-M. The long leg of the spring faces towards the pool as shown in Figure D. Use exploded view on page 9 for

reference. Hand tighten only at this point.

STEP TWO:

Lay the base upside down on the springs and align the 3 holes in each spring center to the base. Orient Edge Base to pool as

shown in Figure E. Use hardware kit EDGE-SP and bolt springs to base. Use exploded view on page 9 for reference. Tighten

the 6 bolts from base to springs at this time to 25-30 FT-LBS.

STEP THREE:

Turn the assembly over and tighten the board to spring hardware that was only hand tightened in step one. Tighten to 20-25

FT-LBS.

STEP FOUR:

Place the Edge stand over the four jig bolts and secure with hardware kit TS-BK. Tighten the Stand Anchor Hex Nuts to

40-45 FT- LBS. Do not over tighten.

The Diving Board must be installed according the below board leveling instructions:

HARDWARE NOTE: Use a small dab of anti seize lubricant (included) on all bolt threads.

POOL WATER POOL WATER

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de iluminación de S.R.Smith

S.R.Smith

S.R.Smith Star Series Manual de usuario

S.R.Smith

S.R.Smith SRS-TX-30 Manual de usuario

S.R.Smith

S.R.Smith TYPHOON Manual de instrucciones

S.R.Smith

S.R.Smith SlideAway Guía de instalación

S.R.Smith

S.R.Smith PT-6001 Power Tower Manual de usuario

S.R.Smith

S.R.Smith ROGUE GRAND RAPIDS Manual de usuario

S.R.Smith

S.R.Smith AQUABLAST Manual de usuario

S.R.Smith

S.R.Smith rogue2 Manual de usuario

S.R.Smith

S.R.Smith R Series Manual de usuario

S.R.Smith

S.R.Smith PAL Series Manual de usuario

S.R.Smith

S.R.Smith FRONTIER II Manual de usuario

S.R.Smith

S.R.Smith Power Tower PT-6002 Manual de usuario

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Manual de usuario

S.R.Smith

S.R.Smith VORTEX Manual de instrucciones

S.R.Smith

S.R.Smith BYOS 2 Manual de programación

S.R.Smith

S.R.Smith LM10 Manual de usuario

S.R.Smith

S.R.Smith pLX-PL60 Guía de inicio rápido

S.R.Smith

S.R.Smith 6004 Series Manual de usuario

S.R.Smith

S.R.Smith multiLift 2 Guía

S.R.Smith

S.R.Smith heliX2 Manual de instrucciones

S.R.Smith

S.R.Smith TURBOTWISTER Manual de instrucciones

S.R.Smith

S.R.Smith rogue2 Manual de usuario

S.R.Smith

S.R.Smith CYCLONE Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario