RVS PD-062710 Manual de usuario
P&D Compliant
Fleet Solution
Instruction Manual
©Rear View Safety 2021
7” Kit
7” Monitor - HD Cameras with 6 Sensors
PD-062710
2©Rear View Safety
1 x 7" 3-Channel Split Screen Monitor
6 x Weatherproof Backup Sensor Reversing System
2 x HD 120° Side Cameras
1 x HD 130° Backup Camera
1 x 50 ft Cable
1 x 16 ft Cable
1 x 10 ft Cable
1 x U Bracket
1 x Fan Bracket
IN THE BOX
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 3
TABLE OF CONTENTS
InTheBox.................................2
SafetyInformation...........................5-6
Overview................................7
Required Tools and Supplies . . . . . . . . . . . . . . . . . . . . . 8
Wiring Requirements – All Vehicles. . . . . . . . . . . . . . . . 8
Wiring Connections and Component Mounting. . . . . . . . . . . 9
Monitor Mounting Overhead in Step Van. . . . . . . . . . . . . . . 11
SideCameras–StepVan ..................... 12
Rear Camera Installation - Step Van. . . . . . . . . . . . . . . 12-13
BackupSensorOverview....................... 14
Sensors and ECU Placement. . . . . . . . . . . . . . . . . . . . . . 15
CableRouting–StepVan........................ 18
Completing the Installation. . . . . . . . . . . . . . . . . . . . . . . 20
Connection Diagram.......................... 21
MonitorOperations........................... 22
Warranty............................... 24
Disclaimer.............................. 25
4©Rear View Safety
If you have questions about this product,
please contact us at:
Phone: 888-544-0260
Email: fedex@rearviewsafety.com
New York
1797 Atlantic Ave
Brooklyn, NY 11233
Indiana
319 Roske Dr.
Elkhart, Indiana 46516
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 5
SAFETY INFORMATION
Please read the entire manual and follow the instructions and warnings carefully.
Failure to do so can cause serious damage and/or injury, including loss of life.
Be sure to obey all applicable local trac and motor vehicle regulations as it
pertains to this product. Improper installation will void manufacturer’s warranty.
USAGE : The Rear View Camera System is designed to help the driver safely
detect people and/or objects helping to avoid damage or injury. However, you
the driver, must use it properly. Use of this system is not a substitute for safe,
proper or legal driving.
• Never back up while looking at the monitor alone. You should always check
behind and around the vehicle when backing up, in the same way as you would
if the vehicle did not have the Rear View Camera System. If you back up while
looking only at the monitor, you may cause damage or injury. Always back up
slowly.
• The Rear View Camera System is not intended for use during extensive back-
up maneuvers or backing into cross trac or pedestrian walkways.
• Please, always remember, the area displayed by the Rear View Camera System
is limited. It does not display the entire panorama that is behind you.
PLEASE READ THE ENTIRE MANUAL AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CAREFULLY. FAILURE TO DO SO CAN CAUSE SERIOUS
DAMAGE AND/OR INJURY, INCLUDING LOSS OF LIFE. BE SURE TO OBEY ALL
APPLICABLE LOCAL TRAFFIC AND MOTOR VEHICLE REGULATIONS AS IT
PERTAINS TO THIS PRODUCT. IMPROPER INSTALLATION WILL VOID
MANUFACTURER'S WARRANTY.
6©Rear View Safety
SAFETY INFORMATION
INSTALLATION
Electric shock or product malfunction may occur if this product is
installed incorrectly.
• Use this product within the voltage range specified. Failure to do so
can cause electronic shock or product malfunction.
• Take special care when cleaning the monitor.
• Make sure to firmly ax the product before use.
• If smoke or a burning smell is detected, disconnect the system
immediately.
• Where the power cable may touch a metal case, cover the cable
with a friction tape. A short circuit or disconnected wire may cause
a fire.
• While installing the RVS System, be careful with the wire positioning in
order to avoid wire damage.
• Do not watch movies or operate the monitor while driving; as it may
cause an accident.
• Do not install the monitor where it may obstruct driver's view or
obstruct an airbag device.
• Dropping the unit may cause possible mechanical failure.
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 7
OVERVIEW
The installed system will consist of:
• 7 inch split screen monitor which:
- Allows viewing multiple cameras at the same time.
- Shows full screen display of camera view when a particular camera is in use.
- Issues audible alerts from the rear sensors when an obstacle is detected while
vehicle is in reverse.
• Driver and Passenger side cameras
There are 2 mounting options:
- Flush mounted. This option is always preferred when possible.
- Bracket mounted.
• Rear backup camera mounted over rear door.
• 6 backup sensors + a sensor control module (ECU).
2 upper sensors will be mounted up high on either side of the vehicle, near the top.
- 4 lower sensors should be mounted at or near bumper level, evenly spaced
along the bumper. For box trucks, please refer to the box truck installation guide.
- The ECU will mount inside the cargo area in the upper driver’s side corner on
all vehicles except straight (box) trucks. On box trucks, the ECU will mount
under the truck on the right rear driver’s side.
8©Rear View Safety
REQUIRED TOOLS & SUPPLIES
- Tall ladder and step ladder.
- Cordless drill and 1/4” accessories.
- Various drill bits.
- 3/4”, 7/8” and 1” hole saws.
- Various hand tools: wrenches, sockets, screwdrivers, etc.
- Wire crimper, wire stripper.
- Measuring tape.
- Wire fish tool.
- Razor knives.
- Brush on primer for cable and sensor holes in sheet metal.
- White touch up paint.
- Long and short zip ties.
- Silicone.
WIRING REQUIREMENTS – ALL VEHICLES
Required power connections:
• Accessory/Ignition
• Chassis Ground
• Reverse
• Left front turn signal
• Right front turn signal
Note: You must use the front turn signal wires unless the rear turn signal and stop
lights are independent of each other. The monitor view will not work properly
when pressing the brake pedal if connected to the stop lights.
NOTE: Wire will have to run from the front to the back of the truck.
Run the Rear Wire of ECU from the REVERSE IGNITION to the rear of the chassis.
Rear View Safety, 1797 Atlantic Ave., Brooklyn NY 11233
www.rearviewsafety.com 9
WIRING CONNECTIONS AND COMPONENT MOUNTING
Component mounting:
• Rear camera will be mounted with machine screws, nuts, and washers. If there
is no access to the backside of camera location, then self-drilling screws can
be used to mount the camera bracket.
• Side cameras must be mounted with the supplied machine screws, nuts, and
washers.
• Each camera requires 3/4” hole for the camera cable.
• Monitor mounting on step vans will depend on location (most will mount
overhead) and use the “U” bracket.
• Monitor requires a 3/4” hole for the cable or use an existing hole in shelf if
present.
10 ©Rear View Safety
MONITOR MOUNTING OVERHEAD IN STEP VAN
In most cases, the monitor will be mounted on the underside of overhead package
shelf of the step van.
• Mount with machine screws/bolts, nuts and washers. Never use self taping/
drilling screws for mounting overhead.
• Sit in driver’s seat to determine the best viewing angle.
• Be mindful of existing equipment, such as fan.
• Use the existing hole in the shelf if available, to route the monitor cable through.
• If no hole exists, drill 3/4” hole. Insert a snap bushing.
Note: Some step vans, like Utilimaster vans as an example are prewired for a
backup camera.
• Utilimaster: Look for a 15 pin plug at top left A pillar.
• Lt/Green - Reverse
• Pink - Ignition
• White - Ground
Tabla de contenidos
