Ruijie Reyee RG-EW300R Manual de usuario
RG-EW300R
1-6
7-12
13-18
19-24
25-30
31-36
37-42
43-48
RG-EW300R Wi-Fi Extender
User Manual
Product Appearance
❶Ethernet Interface
❷LED/RESET Button
❷
❶
❸Signal Status LED
❸
To better use the Ruijie Reyee products, please read this manual before
installation and save it for future reference.
Action
Status
Blinking alternately
White
Off
Three bars on
Two bars on
One bar on
❺
Long press for more than 5s
Short press for less than 2s
Description
Description
The device restores factory settings.
Turn on or off the signal status LED.
The device is accessing the Wi-Fi network of
the primary router.
The signal strength is high.
The signal strength is medium.
The signal strength is low.
1. The device is set to the router mode.
2. The device fails to access the Wi-Fi network
of the primary router.
❹
1
Wi-Fi Extender *1 User Manual *1 Warranty Card *1
1.
Package Contents
Scenario 1: Connect the Device to Other Router
The device is starting
up after power-on.
Installing the Wi-Fi Extender
2. Startup is
complete.
The system status LED
is blinking blue.
Please wait for 1 to 2 minutes.
The system status LED
is solid blue.
❹System Status LED
Status Description
The device is functioning properly. / The port
has made a successful link.
The device is starting up. / The device is restoring
factory settings.
The network is unreachable.
Blue
Red
Solid on
Blinking
Solid on
❺WPS Button
Action Description
Establish a WPS network with other routers.Short press for less than 2s
3. Connect to the SSID @Rui-
jie-sXXXX broadcast by the
Wi-Fi Extender and perform
configuration.
Please visit 10.44.77.254
by browser if the configura-
tion page does not pop up.
2
Operating Status DescriptionLED Status
Factory status
The device
accesses
the network
successfully.
Note:
1. You can download the Reyee Router App to get more management functions of
the extender, such as turning off the signal status LED and modifying the Wi-Fi name
and password.
2. If only one signal bar is on, place the Wi-Fi extender closer to the primary router.
3. You can create a wired network with an Ethernet cable over the 100 Mbps
Ethernet port.
4. The connected Wi-Fi extender can access the Wi-Fi network automatically
upon the next power-on.
5. You can short press the LED/RESET button ❷to turn off the LED.
The device fails to
connect to the
primary router.
The device connects
to the primary
router,while the
network is
unreachable.
The system status LED
❹is solid blue. The
signal status LED ❸is
off.
The system status LED ❹
is solid blue. The signal
status LED ❸is solid
white.The more signal bars
in solid white indicates the
stronger signal.
The system status LED ❹
is solid red. The signal
status LED ❸is off.
The system status LED ❹
is solid red. The signal
status LED ❸is solid
white.
If the device is still in the factory
status after the configuration of the
Wi-Fi Extender is complete, it indi-
cates that the device is not properly
installed. Please move the Wi-Fi
extender closer to the primary router.
Connect to the SSID @Ruijie-sXXXX
and try again.
The network is reachable. The
Wi-Fi extender and the primary
router broadcast the same Wi-Fi
signal by default. You can also set
different Wi-Fis for the Wi-Fi
extender and the primary router.
Please place the Wi-Fi extender-
closer to the primary router.
Please check whether the primary
router accesses the Internet.
3
Operating Status
DescriptionLED Status
Scenario 2: Connect the Device to the Primary Router (WPS)
Factory status
The device
accesses
the network
successfully.
The device fails to
connect to the
primary router.
The system status LED ❹
is solid blue. The signal
status LED ❸is off.
The system status LED ❹
is solid red. The signal
status LED ❸is off.
1. The device is
starting up
after power-on.
2. Startup is
complete. Press the WPS button
on the primary router.
The system status LED
is blinking blue.
Please wait for 1 to 2 minutes.
The system status
LED is solid blue.
The system status LED is solid
blue.Three signal bars are
blinking alternately.
3.
Press the WPS button on the
Wi-Fi extender in 2 minutes.
4.
If the device is still in the factory
status after the configuration of the
Wi-Fi extender is complete, it indi-
cates that the device is not properly
installed. Please place the Wi-Fi
extender closer to the primary
router and try again as instructed in
the figure.
The system status LED ❹ is
solid blue. The signal status
LED ❸is solid white.The
more signal bars in solid
white indicates the stronger
signal.
The network is reachable. The
Wi-Fi extender and the primary
router broadcast the same Wi-Fi
signal.
Please place the Wi-Fi extender
closer to the primary router.
Place the Wi-Fi extender close to the primary router.
Primary routerPower supply faceplate
4
Note:
1. The device already in the WPS networking status will not be paired again if you
press the WPS button.
2. You can short press the LED/RESET button ❷to turn off the LED.
Operating Status DescriptionLED Status
Scenario 3: Connect the Device to the Modem Directly
The device connects
to the network.
The system status LED
❹is solid blue.
Please connect to the
configured Wi-Fi.
1. The device is
starting up
after power-on.
2. Startup is
complete.
Connect to the modem with an
Ethernet cable.
The system status
LED is blinking blue.
Please wait for 1 to 2 minutes.
The system status
LED is solid blue.
The system status LED is solid blue.
3.
4.
Power supply faceplate
ISP modem
Connect to the SSID @Ruijie-sXXXX broad-
casted by the Wi-Fi extender and perform
configuration. Please visit 10.44.77.254 by
browser to perform configuration if the configu-
ration page does not pop up.
The system status LED ❹
is solid red. The signal
status LED ❸is solid white.
Please check whether the primary
router accesses the Internet.
The device
connects to the
primary router,
while the network
is unreachable.
5
Note:
1. You can download the Reyee Router App to get more management functions of
the Wi-Fi extender, such as turning off the signal status LED and editing the
Wi-Fi name and password.
2. The Ethernet interface of the Wi-Fi extender is a 100 Mbps interface.
Router Management
1.App management: You are advised to perform router management on the Reyee
Router App.
2.Webpage management: Visit 10.44.77.254 by browser to perform router manage-
ment.
Troubleshooting
1. Poor signal strength
If only one signal bar of the signal status LED ❸is on after the Wi-Fi extender is
installed, you are advised to place the Wi-Fi extender much closer to the primary
router.
Remark: Please do not install the Wi-Fi extender where the signal strength is the
lowest. Instead, place the Wi-Fi extender between the primary router and the location
with the poorest signal strength level.
2. Factory setting restoration
Press the LED/RESET button ❷for more than 5 seconds. If the system status LED ❹
is blinking blue, the device is restoring factory settings. Please wait for 1 to 2 minutes.
If the LED is solid blue, the device has restored factory settings.
Perform the installation and configuration again after the device restores factory set-
tings. The default SSID is @Ruijie-sXXXX.
3. Password loss
You are advised to enter the Wi-Fi password. If the password is still incorrect, please
restore the device to factory settings (Press the LED/RESET button ❷for more than 5
seconds).
The device fails to
connect to the
network.
Please check cable connection
and network status.
The system status LED
❹is solid red.
6
RG-EW300R
Wi-Fi擴展器快速入門
認識擴展器
❶ 網絡連接埠
❷ LED/RESET按鍵
❷
❶
❸訊號指示燈
❸
為了讓你更好使用銳捷睿易產品，在安裝及使用前，請先閱讀手冊並保存備用
操作
狀態
輪流閃爍
白色
熄滅
三格常亮
兩格常亮
一格常亮
❺
長按>5秒
短按<2秒
說明
說明
裝置恢復原廠設定
關閉或開啟訊號指示燈
正在無線連接主路由
訊號質素優
訊號質素一般
訊號質素差
1、裝置設置為路由模式。
2、無線連接主路由失敗。
❹
7
擴展器主機*1 說明書*1 保養卡*1
1.
包裝清單
場景一：無線連接其他品牌的路由器
連接電源，
裝置啟動中
安裝擴展器
2.
啟動完成
系統指示燈藍燈閃爍
請等候1-2分鐘
系統指示燈藍燈常亮
❹系統指示燈
狀態 說明
裝置完成啟動/已連接網絡
裝置啟動中/恢復原廠設定中
網絡無法連接
藍色
紅色
常亮
閃爍
常亮
❺ WPS按鍵
操作 說明
與其他路由透過WPS自動組建網絡短按＜2秒
3. 連接擴展器發出的Wi-Fi（@Rui-
jie-sXXXX），進行配置,若沒有跳
出配置頁面，請透過瀏覽器存取
「10.44.77.254」
8
Otros manuales para Reyee RG-EW300R
1
Tabla de contenidos
Idiomas:
Otros manuales de Extensor de Ruijie
