Ruijie RG-WS5708 Series Manual de instalación y funcionamiento
RG-WS5708 Series Wireless Controller
Hardware Installation and Reference Guide V1.1
Copyright statement
Ruijie Networks©2000-2013
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
, , , ,
,,
,, ,
, , are registered trademarks of Ruijie
Networks. Counterfeit is strictly prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.
Preface
Thank you for using our products. This manual will guide you through the installation of the wireless controller.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijie.com.cn
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: +86-4008-111-000
BBS:
http://support.ruijie.com.cn
Customer services email: [email protected]
Related Documents
Documents Description
Configuration Guide Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or
cause data loss.
Chapter 1 Product Overview
The RG-WS5708 wireless LAN controller is introduced by Ruijie Networks to provide powerful WLAN access control for
medium-large-sized wireless networks. The following table lists the number of various ports on the front panel of the
wireless controller.
Model 10/100/1000Base-T
auto-sensing Ethernet ports
1000Base-X
SFP ports 10G SFP+ ports Console ports MGMT ports
WS5708 8 8 2 1 1
A fiber/copper combo port is composed of the 1000Base-X SFP port and the corresponding 10/100/1000Base-T
self-adaptive Ethernet port, and only one of the ports can be used at one time.
A Gigabit/10G combo port is composed of four Gigabit fiber/copper combo ports and the corresponding 10G SFP+ ports,
and only one group of ports can be used at one time.
To activate a fiber/copper combo port, you need to restart the wireless controller, but to activate a 10G/1G
combo port, you do not need to.
Model 1000Base-X SFP ports 10/100/1000Base-T auto-sensing Ethernet ports SFP+ ports
1F 1
2F 2
3F 3
4F 4
XF2
5F 5
6F 6
7F 7
RG-WS5708
8F 8
1XF
Technical Specifications
Table 1-1 Technical Specifications of RG-WS5708
Model RG-WS5708
Optical Modules
Gigabit Ethernet:
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
Mini-GBIC-ZX50
Mini-GBIC-ZX80
Mini-GBIC-ZX100
1000Base-T:
Mini-GBIC-GT
10-Gigabit SFP+ module:
XG-SFP-SR-MM850
XG-SFP-LR-SM1310
The supported SFP modules may be updated at any time. For details, please contact us.
SFP Ports Support 1000Base-X
Power Supply
Support 1+1 power redundancy
Power module: RG-PA300I
Rated voltage range: 100 to 240 V AC
Maximum voltage range: 90 to 264 V AC
Frequency: 50 to 60 Hz
Rated current: 6.3 A
Power Consumption Less than 83 W
0 to 45ºC (32 to 113℉)
Temperature -40 to 70ºC (-40 to 158℉)
10% to 90% RH
Humidity 5% to 90% RH
Fans Support fan speed adjustment and fault alarm
Support hot swappable fan trays
EMC GB9254-2008, GB17625.1-2003
Safety GB4943-2001
Size (W x D x H) 440 mm x 420 mm x 88.1 mm
17.32 in. x 16.54 in. x 3.47 in.
Weight 11 kg (24.25 lbs)
Product Image
The wireless controller provides eight Gigabit SFP combo ports, two 10-Gigabit SFP+ ports, one Console port, one MGMT
port on the front panel, and two power supply slots and one fan tray slot on the back panel.
Figure 1-1 Product Image of RG-WS5708
Front Panel
Figure 1-2 Front Panel of RG-WS5708
Note 1. System status LED
2. MGMT port LED
3. 10/100/1000Base-T auto-sensing Ethernet port
LEDs
4. 1000Base-X LEDs
5. Console port
6. MGMT port
7. 10/100/1000Base-T auto-sensing
Ethernet ports
8. 1000Base-X SFP ports
9. SFP+ port LEDs
10. SFP+ ports
Back Panel
Figure 1-3 Back Panel of RG-WS5708
Note 1. Ground rod
2. Power supply slots
3. Fan tray slot
Power Supply
The wireless controller uses RG-PA300I power modules.
The RG-PA300I modules receive AC input.
Rated voltage range: 100 V to 240 V AC
Maximum voltage range: 90 V to 264 V AC
Frequency: 50 to 60 Hz
Rated current: 6.5 A
Power cord: 10 A
Cooling Solution
The fan tray locates at the left side of the chassis and the fan tray slot locates at the back panel. A fan tray contains four
hot-swappable fans. The wireless controller supports fan fault alarms and speed adjustment. Figure 1-4 illustrates the
structure of the fan tray.
Figure 1-5 Fan Tray of the RG-WS5708
LED Indicators
LED State Meaning
Off The wireless controller is NOT receiving power.
Blinking green
Initialization in progress.
Continuous blinking indicates errors.
Solid green The wireless controller is operational.
Status
Solid red The wireless controller is faulty. See Section 5.2 Troubleshooting
Off The SFP port is NOT connected.
Solid green The SFP port is connected at 1000 Mbps.
1F 2F 3F 4F
5F 6F 7F 8F
Blinking green The SFP port is receiving or transmitting traffic at 1000 Mbps.
Off The Ethernet port is NOT connected.
Solid green The Ethernet port is connected at 1000 Mbps.
Blinking green The Ethernet port is receiving or transmitting traffic at 1000 Mbps.
Solid yellow The Ethernet port is connected at 10/100 Mbps.
1 2 3 4 5 6 7 8
Blinking yellow The Ethernet port is receiving and transmitting traffic at 10/100 Mbps.
Off The SFP+ port is NOT connected.
Solid green The SFP+ port is connected.
1XF 2XF
Blinking green The SFP+ port is receiving or transmitting traffic.
Chapter 2 Preparing the Installation
Safety Recommendations
To prevent device damage and bodily injury, please read carefully the safety recommendations described
in this chapter.
The recommendations do not cover all possible hazardous situations.
Installation Safety
Keep the chassis clean, free from any dust.
Do not place the device in a walking area.
Do not wear loose clothes or any other things that may be caught by the chassis during installation and
maintenance.
Before uninstalling the chassis, power off and unplug all power cables.
Movement Safety
Avoid moving the device frequently.
Keep balance when moving the device, and avoid injuring your leg and feet or spraining your waist.
Turn off all power supplies and unplug all power cables before you remove the device.
Electrical Safety
Please observe local regulations and specifications when performing electrical operations. Relevant operators must
be qualified.
Please carefully check for any potential danger in the working area, for example, ungrounded power supply,
unreliable grounding of the power supply and damp/wet ground or floor.
Find out the location of the emergency power supply switch in the room before installation. First cut off the power
supply in case of an accident.
Do not do the maintenance with the power on by one person.
Be sure to make a careful check before you shut down the power supply.
Do not place the device in a damp/wet location. Do not let any liquid enter the chassis
Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock,
thus causing severe even fatal damages to human bodies and device.
Direct or indirect touch through a wet object on high voltage and power line can bring a fatal danger.
ESD Prevention
To prevent damage from static electricity, note that:
Properly ground the device.
Take dust prevention measures in the room.
Maintain an appropriate humidity.
Laser Safety
Most of the optical modules used by the wireless controller are Class I laser products. Observe the following:
When a fiber transceiver is working, ensure that the port has been connected to a fiber cable or is covered with a
dust cap so as to keep out dust and avoid burning your eyes.
Do not stare into any fiber port.
Do not stare into any fiber port under any circumstances, which may cause permanent damage to your eyes.
Preparing Installation Site
The wireless controller must be installed indoors. To ensure normal operation, the installation site must meet the following
requirements.
Ventilation
For proper ventilation, leave a minimum clearance of 10 cm (3.9 in.) from the rear and both sides of the chassis. And bind
your loose cables together or place them on a cable tray to avoid blocking the air inlets.
Temperature and Humidity
To ensure normal operation and service life of the device, maintain appropriate temperature and humidity levels in your
equipment room. See Table 2-1. Improper room temperature and humidity can cause damages to the device.
High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage, and
sometimes may lead to change of mechanical properties of materials and corrosion of metal parts.
Low relative humidity may dry and shrink insulation sheets and cause static electricity that can damage the circuitry
inside the device.
High temperature greatly reduces reliability of the device and shortens its service life.
Table 2-1 Required Temperature and Humidity for the RG-WS5708
Temperature Relative Humidity
Tabla de contenidos
Otros manuales de Controladores de Ruijie
Ruijie
Ruijie RG-WS6108 Series Manual de instalación y funcionamiento
Ruijie
Ruijie RG-WS6512 Manual de instalación y funcionamiento
Ruijie
Ruijie RG-WS6108 Series Manual de instalación y funcionamiento
Ruijie
Ruijie RG-WS6816 Series Manual de instalación y funcionamiento
Ruijie
Ruijie RG-WS6024 Series Manual de instalación y funcionamiento
