Rugged Ridge 11546.22 Manual de usuario
11546.22
Jeep®JK Wrangler XHD Rear Tire Carrier
Contents:
1. Frame (1)
2. Pivot Mount (1)
3. Latch Mount (1)
4. Lug Nuts (3)
5. Catch Pin (1)
6. M12 Washer (18)
7. M12 x 30 Hex Bolt (14)
8. Brake Light Mount (1)
9. Snap Ring (1)
10. Rub Strip (1)
11. Latch (1)
12. Bearing (2)
13. Spare Mount Plate (1)
14. M12 Lock Nut (7)
15. Spare Adjuster Plate (1)
16. Bearing Cap (1)
17. Castle Nut (1)
18. Cotter Pin (1)
19. Catch (1)
20. M6 Washer (12)
21. M6 x 20 Socket Cap Screw (2)
22. Ramp (1)
23. Brake Light Screw, Short (2)
24. Bumper Stop (2)
25. Ramp Shim (5)
26. Brake Light Screw, Long (2)
27. M6 x 20 Hex Bolt (10)
28. Safety Pin (1)
29. Wire Ties (8)*
30. Wire Loom (1)*
31. Rubber Plug (1)*
32. M16 Flat Washer (1)
1. If installing with a new XHD Rear Bumper, Install bumper brackets and place bumper on brackets,
but do not install D-Rings.
If installing on an existing XHD Rear Bumper, remove D-Rings. It may be necessary to loosen
brackets to help with hole alignment.
Remove spare tire and spare tire mount. Unplug third brake light wiring and set to the side.
Remove third brake light from spare tire mount.
Page 1 of 9
22
1
2
3
4
5
9
6
7
8
10
11
19
12
13
14
16
17
18
21
20
22
25
24 23
26
15
27
32
28
* Not Shown in Exploded View
Page 2 of 9
2. Place Pivot Mount (#2) on the right side of the bumper. Install using M12 Hex Bolts (#7) in the top
holes, and place the D-Rings and its corresponding bolts in place on the rear holes. Leave all bolts
loose. Note - (2) bolts that are closest to the tailgate do not get washers. All other bolts do.
3. Place Latch Mount (#3) on the left side of the bumper. Install using M12 Hex Bolts (#7) in the top
holes, and place the D-Rings and its corresponding bolts in place on the rear holes. Leave all bolts
loose. Note - (1) bolt that is closest to the tailgate does not get a washer. All other bolts do.
4. Pre-assemble Spare Tire Mount. Spare Mount Plate (#13) and Spare Adjuster Plate (#15) nest inside
one another. Fasten together with (4) M12 Hex Bolts (#7), (8) M12 Washers (#6), and (4) M12 Lock
Nuts (#14) as shown. Leave fasteners loose.
Page 3 of 9
5. Fasten Spare Tire Mount Assembly from Step 4 to the Frame (#1) using (3) M12 Hex Bolts (#7),
(6) M12 Washers (#6), and (3) M12 Lock Nuts (#14) as shown.
6. Install Ramp (#22) onto Frame (#1) using (2) M6 Socket Cap Screws (#21) and (2) M6 Washers (#20)
as shown. Shims (#25) may have to be added later during adjustment.
7. Install (2) Bumper Stops (#24) onto Frame (#1) using (4) M6 Hex Bolts (#27) and (4) M6
Washers (#20) as shown. Leave fasteners loose, as they will need to be adjusted to the vehicle later.
8. Pack (2) Bearings (#12) with all purpose grease. Install (1) Bearing onto spindle of Pivot Mount (#2).
Page 4 of 9
9. Lift Frame (#1) onto vehicle, setting the pivot end on the spindle as shown and resting the latch end on
the opposite end. Install second Bearing onto spindle. Install Bearing Cap (#16), M16 Washer (#32)
and Castle Nut (#17) onto spindle. Tighten Castle Nut until all slack is removed from pivot assembly,
but frame still pivots freely. Install Cotter Pin (#18).
10. Tighten bolts on the Pivot Mount Plate (#2). Latch the Latch (#11) to the Catch (#19). Ensure that
the Latch swings freely into place to engage the catch. It may be necessary to adjust the Latch, the
Catch, and/or the Latch Mount to achieve this. Once adjusted, tighten the Latch Mount into place.
11. Adjust Bumper Stops (#24) so that the OE rubber bumpers on the tailgate compress approximately
1/2" when the Tire Carrier is latched.
12. If the Latch (#11) has room above it when it engages the Catch (#19), it may rattle on bumpy terrain.
This gap can be eliminated by installing Shims (#25) between the Ramp (#22) and the Frame (#1)
until the gap is closed.
Page 5 of 9
13. Remove tape backing from Rub Strip (#10) and place around spindle. The hole should line up with
hole in Pivot Mount (#2), and the curve should wrap around spindle as shown.
15. Remove the 4 torx head screws that attach the light to the factory tire mount. Pull the light away
from the tire mount. Remove the connector by pushing down on the tab and pulling. Set the light
aside, it will be used later during the installation.
14. Install spare tire using provided (3) Lug Nuts (#4). It will be necessary to adjust the Spare Tire Mount
Assembly to achieve proper fit. Spare tire should be vertical, and should rest against Frame (#1)
when properly adjusted.
Note: At this point, Tire Carrier is installed and adjusted. Remaining directions refer to installation of
third brake light.
Page 6 of 9
16. Open the tailgate and remove the tailgate vent. Pull out along the left edge first and pull. Locate the
2 wire brake light connector located in the opening. Push the tab in and pull to remove the connector.
17. Remove the rubber grommet with the wiring on the outside of the tailgate by grabbing it and working
it out of the hole. Pull the wiring through being careful not to damage it. Set this small harness aside,
it will be reused later. Insert Rubber Plug (#31) into the empty hole.
18. Remove the other portion of the third brake light connector from the tailgate. Locate the wiring going
to the tailgate latch. It should run just above the third brake light wiring going towards the right.
Follow it to the latch and remove the connector in the same method as mentioned earlier.
19. Remove the long plastic cover that runs almost the length of the upper portion of the tailgate.
This is done by pulling out along the bottom edge of the cover first. You should now see the wiring
harness. Carefully pull the harness through the small access hole that is to the right. The connectors
will need to be guided through the hole one at a time.
Page 7 of 9
20. Once the wiring and connectors are removed from inside the tailgate, remove the third brake light
wiring and connector from the short piece of loom.
21. Brake light connector can now be disassembled. Note the location of the wires before removal.
Holding the third brake light connector, carefully pull out on the two white tabs of the terminal lock
that are on each side of the connector and push them into the grey connector. With a small
screwdriver pry the terminal lock out of the connector. This will now allow both terminals and wires
to be removed from the connector. Set the terminal lock aside it will be reused a little later.
22. With the terminal lock removed you can now remove the two wires and terminals. Using a paper clip,
slide it under the wire and push in. It will feel like it snaps in place when pushed all the way in.
Holding both the wire and paper clip, pull them both out of the connector. Do the same with the
other wire.
23. Carefully pull the 2 wires all the way through the insulator. It is recommended that these wires be
wrapped in electrical tape to better protect them from weathering and becoming worn. Then wrap
them with Wire Loom (#30).
Page 8 of 9
24. Pull the carpeting away from the tailgate seal. Route the wiring for the third brake light wiring along
the tailgate seal. You do not have to tuck it behind the seal, as it will be concealed by the carpet.
Route the wiring under the lower right hand corner of the tailgate seal.
25. Wrap the wiring with the provided Wire Loom (#30) beginning inside the vehicle. Pass the wrapped
wire between the body and the tailgate seal. Close the tailgate and continue to route the wiring to the
tire carrier. Route the wiring along the tire carrier as shown. Secure wiring to Tire Carrier with
Wire Ties (#29).
25. Reinstall the harness removed in Step 17. Install the third brake light assembly into the new light
bracket that was provided with your new tire carrier. Install the 4 provided phillips head screws
(#23 ) and tighten. Be careful not to over-tighten these screws.
Page 9 of 9
26. Install the light and bracket assembly into the provided square hole in the tire carrier. There are 4
holes provided for adjustability. Install it in the hole that provides best visibility above the spare tire.
Install the provided M12 Bolt (#7) and Washer (#6) and tighten.
27. Reassemble the connector. Assembly is just the reverse of disassembly. When reinstalling the
terminal ends the paper clip that was used will not be needed. Be sure to push the terminals in until
they snap into place.
28. Connect the wire coming from vehicle with the wire coming from third brake light. Wrap all exposed
wiring with provided wire loom. Secure loose wiring to the tire carrier with provided wire ties.
Finally, test the operation of the third brake light.
Installation is complete. Should tire carrier rattle as it ages, it can be adjusted as indicated in steps 11
and 12. Congratulations on your purchase of another quality Rugged Ridge product.
© Copyright 2008, Omix-Ada
Omix-Ada Inc.
460 Horizon Dr. Suite 400
Suwanee, Georgia 30024
Otros manuales de Accesorios para automóviles de Rugged Ridge
Rugged Ridge
Rugged Ridge 11546.23 Manual de usuario
Rugged Ridge
Rugged Ridge 11425.15 Manual de usuario
Rugged Ridge
Rugged Ridge 18003.10 Manual de usuario
Rugged Ridge
Rugged Ridge 13510.10 Manual de usuario
Rugged Ridge
Rugged Ridge 18003.30 Manual de usuario
Rugged Ridge
Rugged Ridge 11703.03 Manual de usuario
Rugged Ridge
Rugged Ridge 11504.37 Manual de usuario
Rugged Ridge
Rugged Ridge 11232.09 Manual de usuario
Rugged Ridge
Rugged Ridge 13551.34 Manual de usuario
Rugged Ridge
Rugged Ridge 11594.02 Manual de usuario
Rugged Ridge
Rugged Ridge 11509.32 Manual de usuario
Rugged Ridge
Rugged Ridge 11232.20 Manual de usuario
Rugged Ridge
Rugged Ridge 11546.20 Manual de usuario
Rugged Ridge
Rugged Ridge 11210.11 Manual de usuario
Rugged Ridge
Rugged Ridge 11570.10 Manual de usuario
Rugged Ridge
Rugged Ridge 11025.10 Manual de usuario
Rugged Ridge
Rugged Ridge J21068 Manual de usuario
Rugged Ridge
Rugged Ridge 13551.35 Manual de usuario
Rugged Ridge
Rugged Ridge 11504.36 Manual de usuario
Rugged Ridge
Rugged Ridge 53701.52 Manual de usuario
