Ruger RC1000 Manual de usuario
Job# 610/798
David Round & Son, Inc.
Ruger Products Division
32405 Aurora Road
Cleveland, OH 44139
Phone: 440-248-4700
Fax: 440-248-8544
Email: [email protected]
www.rugerindustries.com
OPERATOR’S MANUAL
For safety, one
copy of this
manual must be
stored on the
equipment and
referred to by all
operators.
IMPROPER USE
OF THIS EQUIPMENT
CAN BE HAZARDOUS!
RC1000
All operators must read,
fully understand,
and apply all safety
instructions, before
operating this equipment.
SERIAL NUMBER
MD1001E2OM
Copyright 1999, Ruger Industries, Inc.
ii
Congratulations on your purchase of a standard design Economy Crane. You now
own one of the most versatile cranes in the market. In order to ensure many years of
safe and dependable service, please read this Operator’s Manual before using the
equipment. If you have any questions or need additional information, please contact us
at:
Phone: 440-248-4700
Toll Free: 800-535-2725
Fax: 440-248-4700
www.rugerindustries.com
E-mail: [email protected]
Below is a list of standard accessories that you should have received with your RC1000
• Operator’s Manual
• Swivel Hook with Safety Latch
• Extension Boom
• Extension Boom Safety(Detent) Pin
• Pump Handle
Designers & Manufacturers of Hydraulic Load Lifting and Material Handling Equipment
Contents
General Information.........................................................................1
Receiving and Pre-operational Instructions..........................................1
Returned Goods Authorization........................................................2-3
Insert Sheets...............................................................................4-5
Maintenance Instructions.................................................................6
Recommended Parts.....................................................................7-9
Jack Inspection Check List...........................................................................10
Jack Service Instructions...........................................................................11
Operational Steps...........................................................................12
Lubrication....................................................................................13
Safety Tips for Using Ruger Cranes..................................................14
Warranty.................................................................................15-17
iii
Designers & Manufacturers of Hydraulic Load Lifting and Material Handling Equipment
GENERAL INFORMATION
1. When ordering parts indicate the Model and Serial Number. This information is provided
to you on the front cover of this manual. The Model and Serial Number can also be found on the
Serial Number tag on the unit located on the mast section of the equipment.
2. Ruger Parts Department can be reached at (440-248-4700) 9 AM to 5 PM EST. time, Monday
through Friday except for holidays.
3. Terms are Net 30. Minimum order is $50.00 . All parts are FOB Solon, Ohio.
4. Quality at Ruger starts with raw materials which are inspected to insure our products will be of
good quality and free from defects. Each Economy Crane is tested completely and checked before
shipment.
RECEIVING AND PRE-OPERATIONAL INSTRUCTIONS
Upon receipt of this unit, visually inspect for damage that may have occured during shipment and
report any damages to the carrier.
In accepting this shipment from Ruger Industries, Inc. the carrier has acknowledged receipt in good
condition and complete as shown on the Packing List and/or Bill of Lading.
Ruger Industries responsibility for this shipment has now ceased. Any shortages or damage must
now be resolved between the carrier and the receiver.
Ruger Industries will not be responsible for loss or damage when you give the transportation com-
pany a clear receipt.
Inspect this material before accepting. Do Not accept when damage or shortages are visible un-
less the carrier makes a damage notation on your freight bill.
Look for and report concealed loss or damage to carrier with 48 hours and request inspection by the
carrier. This is absolutely necessary, otherwise, the transportation companies will not entertain any
claim for loss or damage. If the carrier will not make an inspection, then you should make an affidavit
that you notified him/her (on a certain date) and he/she failed to do so. This, with other papers, will
properly support your claim.
Ruger Industries is willing to assist in every possible manner in collecting claims for loss or damage,
but this willingness on Ruger’s part does not include responsibility for collection of claims or as-
sumption of cost of replacement of damaged or lost materials.
CAUTION
DO NOT remove this tag
BEFORE ACCEPTING DELIVERY FROM THE CARRIER
In accepting this shipment from Ruger Industries, Inc., the carrier has acknowledged receipt in good
condition and complete as shown on the packing list and/or Bill of Lading.
2
RECEIVINGPROCEDURES
RECEIVING INSPECTION CHECK LIST
Check wheels and casters - they should turn freely and be free of dents,
cracks and flat spots.
Check main frame components,legs, forks, booms, handles and sheet
metal for dents, cracks and misalignment.
Check wiring to assure it is securely connected and in good condition.
Check main structure bolts, nuts and pin retainers for tightness.
After visual inspection, make operational test to assure unit is
functioning properly.
Is everything there? Check packing list to be sure optional equipment
is there. Make sure lifting chain is with crane. Be sure manual pump
handle is there.
Paint finish -scratches and scrapes to painted surfaces incurred
during shipment are accepted as necessary evil. Costs of protective
crating to protect paint are so high that it's better to accept a few
scrapes to the finish.
Check hoses, fittings and rams for hydraulic leaks.
Hydraulic leaks indicate loose or broken fittings, hoses etc. Hose
and tubing should be free of kinks and buckles.
Check chains and cables for breaks or obstructions.
Check batteries for cracks, leaks. Check electrolyte level.
√√
√√
√
√√
√√
√
√√
√√
√
√√
√√
√
√√
√√
√
√√
√√
√
√√
√√
√
√√
√√
√
√√
√√
√
√√
√√
√
Packing slip must accompany all returns.
CREDIT WILL ONLY BE ISSUED AT THE TIME OF
RETURNED GOODS AT THE FACTORY
When calling for a RETURNED GOODS AUTHORIZATION number the following
information must be supplied:
RECEIVING DOCK DELIVERIES
MONDAY THROUGH FRIDAY
8:00 A.M. TO 4:00 P.M. EST
EXCEPT HOLIDAYS
3
RETURNED GOODS AUTHORIZATION number must be
assigned by the Ruger customer service department for
approved returns. This number must appear on all accompany-
ing paperwork.
RETURNED GOODSAUTHORIZATION
1) Invoice Number
2) Date of Invoice
3) Serial Number
4) Carrier Name
5) Return Ship Date
6) Reason for Return
There will be a restocking charge for all returned purchases. Customized units are
not returnable and are non-refundable.
4
RC1000
STANDARD FEATURES
Prices, Specifications, and Options are subject to
Change Without Notice.
All Ruger products are shipped F.O.B. Solon, Ohio 44139
Unit Ships-NMFC #118900 Sub 3 - Class 125
Shipping Wt. 210 lbs
Maximum Value and Safety at a
Modest Investment.
The RC1000 has a
manual built-in telescopic exten-
sion boom for more reach and
height.
Tested and exceeds
ANSI/ASME PALD-12C
standards.
Meets ANSI Z.535
AFFORDABLE
COMPACT
VERSATILE
RELIABLE
1000 lb. Capacity
Compact Design to work in close
quarters.
ACCESSORIES
Barrel Grip
Floor Lock
Meets Ruger’s structural engineering standards for
150% of normal lifting capacity
Completely self-contained hydraulic system with
single action jack
Built-in hydraulic overload relief valve
(An original Ruger patent)
Needle type release valve permits pin-point control over low-
ering and holding of the heaviest or lightest loads
Standard adjustable telescopic boom
Standard casters with non-marking hard rubber
wheels with sleeve bearing
Swivel hook with a safety latch to support heavy loads
David Round & Son, Inc.
Ruger Products Division
32405 Aurora Road
Cleveland, OH 44139
Phone: 440-248-4700
Fax: 440-248-8544
Email: [email protected]
www.rugerindustries.com
AFFORDABLE
COMPACT
VERSATILE
RELIABLE
MODEL: RC1000
Certain models can be
shipped NEXT DAY.
Ask About our
SPECIAL financing
packages.
NOTE:
Ruger can modify
any standard
dimensions
to meet specific
customer needs.
PUMPING CYCLES
needed to raise boom
through full travel - 90.
ModelRC ..................................................1000
Capacity ...............................................1000 lbs
Overall base length ....................................53 1/8”
Overall width ..............................................35”
Overall height ............................................72 1/2”
Width between legs ...................................28 3/4”
Overall boom length .......................................45”
Max. O.A. boom length with extension ............52”
Boom height (lowest position) ..................34”
Boom height (highest position) .........107 1/2”
Ext. boom height (lowest position) ............24 1/2”
Ext. boom height (highest position) ...............117”
Height of legs ...............................................6 7/8”
Wheel diameter-load wheels ..............................5”
Wheel diameter-steering wheels .........................5”
MAINTENANCE INSTRUCTIONS
NOTE: There is an overload relief valve built into the hydraulic system of every new Ruger Crane.
This safety valve is set at the factory, under measured loadings, and opens at about 10% over the
rated capacity, preventing the crane from lifting.
IF THE CRANE FAILS TO HOLD OR LIFT ITS RATED LOAD.... REMOVE THE CRANE FROM
ALL SERVICE WORK. Contact the factory Customer Service Department at (440) 248-4700.
When calling the factory, please have your Model
and Serial Number ready, so we may better serve you.
EVERY TIME USAGE -
Check the Hydraulic Jack for oil leakage.
(See diagram #1, Page 7, Item No. 1)
Inspect the Safety Swivel Hook with Latch to ensure safe lifting of loads.
(See diagram #1, Page 7, Item No. 4)
WEEKLY -
Check the Pins for excessive wear.
(See diagram #1, Page 7, Items No. 9 and 10)
MONTHLY -
Check the Casters for excessive wear or uneven travel.
(See diagram #1, Page 7, Item No. 2 - 2.1 and Item No. 3 - 3.1)
QUARTERLY -
Check all welded joints.
Serial No. Tag -
Found on the
mast of the
Crane.
www.rugerindustries.com
E-mail: [email protected]
Phone: (800) 535-2725
Fax: (440) 248-8544
...a better way to work with heavy loads
6
7
1
20
17
32
31
30
29
28
27
26
25
24
23
22
21
40
39
15
16
8
19
4
9
8
9
5
6
7
10
11
12
13
14
34
35 36 37
2
3
38
18
RECOMMENDED PARTS
33
Tabla de contenidos
Otros manuales de Equipos de construcción de Ruger
