Ruby Tech 24-Port 100BaseTX + 2-P Manual de usuario

Gigabit Smart Switch

Table of Contents

Introduction

Getting to Know the Switch

LEDs

The Gigabit Ports

The Fiber Ports

The Back Panel

Installing the Switch

Pre-Installation Considerations

Desktop Installation

Rack Mounting

Powering on the Switch

Uplinking the Switch

Configuring the Switch through Console Interface

Overview

Configuring the Hyper Terminal Setup Program

Getting Started

Log-in

Switch Main Menu

PortStatus

Port Configuration

Trunk Configuration

VLAN Configuration

Port Monitoring Configuration

QoS Configuration

Bandwidth Control

Misc Operation

Log out

Configuring the Switch through Web

Log-in

Web Interface

Welcome Page

PortStatus

Gigabit Smart Switch

Port Configuration

Trunk Configuration

VLAN Configuration

Port Monitoring Configuration

QoS Configuration

Bandwidth Control

Misc Operation

Log out

Specifications

Cable Specifications

Technical Specifications

Environmental Information

Standard Conformance

Appendix: Warranty Information

Gigabit Smart Switch

The information in this guide may change without notice. The manufacturer assumes

no responsibility for any errors, which may appear in this guide.

Ethernet is a trademark of XEROX Corporation. Microsoft, Windows and Windows logo

are trademarks of Microsoft Corporation.

transmitted or reproduced in any form or by any means without the written permission

of the manufacturer. Printed in Taiwan.

The revision date for this guide is Jul. 3th, 2004

Version 1.0v

FCC Statement

This product has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of FCC Rules. These limits are designed to provide

reasonable protection against such interference when operating in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy,

and if not installed and used according to the instructions, may cause harmful

interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which

case the user, at his or her own expense will be required to take whatever measures

may be required to correct the interference.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio

interference in which case the user may be required to take adequate measures.

Gigabit Smart Switch

Introduction

24-Port 10/100BaseTX + 2-P Gigabit Smart Switch

Manage the networking depending on your need of connectivity speed with the Smart

Switch! 24-Port 10/100BaseTX + 2-P Gigabit Smart Switch provides 24 100BaseTX

ports, in addition, it is designed with 2 Gigabit and Fiber ports, which enables you to

speed up your connectivity very easily. Installation of the smart switch is very simple. It

takes just few minutes to plug in the RJ-45 cables and Fiber into 10/100Mbps ports

and , and then it’s available. With the device, you can combine Fast Ethernet, and

Gigabit Ethernet solutions all in one.

Featured with the smart function, you can easily configure the switch through the

console interface. With the tree-like configuring program, the utility interface makes you

to view and set value quickly and simply.

The switch is a flexible and economical solution to apply networking management in

whether enterprise or living. Through the guide, the smart switch will be referred as the

switch.

Feature

24 10/100Mbps MDI/MDI-X ports + 2 optional 1000Mbps ports

Non-blocking wire-speed forwarding and filtering

Store and forward architecture and head of line blocking prevention

All ports support auto-negotiation

Broadcast storm filtering control

802.3x full duplex flow control and back pressure half duplex flow control

Trunking with load balance and fault tolerance for 10/100M port

Up to 26 VLAN groups for port based VLAN and 802.1Q tag VLAN

Per-port bandwidth control

Support two priority queues: Static priority and 802.1p priority

Gigabit Smart Switch

Getting to Know the Switch

FrontView

LEDs

LEDs Color Function

POWER Green Lights to indicate the power is being supplied to Switch

LINK/ACT Green Lights to indicate a functional network link through the

corresponding port (1 through 24) with an attached device.

Blinks to indicate that the Switch is actively sending or

receiving data over that port

FDX/COL Orange Lights to indicate that the port is working at full duplex mode.

Blinks to indicate that the port encounters collision

100Mbps Green Lights to indicate the port is working in 100Mbps

1000Mbps Green Lights to indicate the port is working in Gigabit mode.

RearView

TheGigabitPorts

The switch is equipped with two Gigabit ports. They are provided to link to high-speed

network peripheral system or clients at speeds of up to 1000Mbps.

24 10/100Mbps Port10/100Mbps LEDs

1000Mbps LEDs

Console Port

Gigabit Port Fiber Port

Power

Gigabit Smart Switch

TheFiberPort

The switch is equipped with two fiber ports. They are provided to link to fiber to expand

the switch application in various environment. The fiber ports are designed for other

peripheral devices that require very high bandwidth. Using fiber cable to connect

devices, it supports full-duplex data transfer rates of 1000Mbps.

Gigabit Smart Switch

Installing the Switch

This part describes how to install the Switch and make connections to it. Please read

the following instructions step by step. Besides, the Switch does not need software

installation. Install the Switch either on a desktop or a rack.

Pre-Installation Considerations

Before installing the Switch, make sure that the RS232 cable complies with cable

specification. Since the Switch is configured through the console port, the PC must be

equipped with the console interface as well.

Desktop Installation

Step 1

Attach the rubber feet to the recessed areas on the bottom of the Switch. See Figure 1.

Figure 1 Attaching the Rubber Feet to the Bottom of the Switch

Step 2

Place the Switch on a desktop near an AC power source.

Step 3

Keep enough ventilation space for the Switch.

Note: Pleas check the environmental restrictions mentioned in specifications as you

are placing the Switch.

Step 4

Connect the Switch to network devices.

A. Connect one end of a standard network cable to the 24 RJ-45 ports

B. Connect the other end of the cable to the network devices such as printer servers,

workstations or routers, and so on.

Gigabit Smart Switch

Note: Connection to the Switch requires UTP CAT5 network cable with RJ-45 tips. For

more information, please see the cable specifications.

Rack Mounting

To rack-mount the Switch in any standard 19-inch rack, follow the instructions

described below.

Step 1

Place the Switch on a hard flat surface with the front panel faced towards your front

side

Step 2

Attach a rack–mount bracket to one side of the Switch with supplied screws attached to

the package. Figure 2 shows how to attach brackets to one side of the Switch.

Figure 2 Attaching the Brackets to the Switch (Front Panel Forward)

Caution: Please use the screws supplied with the mounting brackets. Damage caused

to the parts by using incorrect screws would invalidate your warranty.

Step 3

Secure the brackets tightly.

Step 4

Follow the same steps to attach the other bracket to the opposite side.

Step 5

After the brackets are attached to the Switch, use suitable screws to securely attach

the brackets to any standard 19-inch rack as shown in Figure 3.

Gigabit Smart Switch

Figure 3 Mounting the Switch in A Rack

Step 6

Connect the Switch to network devices.

A. Connect one end of a standard network cable to the 24 RJ-45 ports

B. Connect the other end of the cable to the network devices such as printer servers,

workstations or routers, and so on.

Step 7

Supply power to the Switch

Connect one end of the power cable to the Switch.

Connect the other end to a standard wall outlet.

When the Switch receives power, the Power LED should show as solid green.

PoweringontheSwitch

Supply power to the Switch

A. Connect the AC power cord to the back of Switch.

B. Plug the power cord into a standard electrical outlet.

C. Then the Switch will boot up automatically. When the Switch receives power, the

Power LED should show as solid green.

UplinkingtheSwitch

To uplink the Switch, connect one end of a Cat5 (or better) cable into 24 100BaseTX

ports, and then connect the other end of the cable into the peripheral device’s uplink

port.

Tabla de contenidos

Otros manuales de Cambiar de Ruby Tech

Ruby Tech

Ruby Tech GS-2108C Manual de usuario

Ruby Tech

Ruby Tech FGS-2824 Manual de usuario

Ruby Tech

Ruby Tech Web-Smart GS-1208M Manual de usuario

Ruby Tech

Ruby Tech ES-1126C/D Manual de usuario

Ruby Tech

Ruby Tech GS-2148L Manual de usuario

Ruby Tech

Ruby Tech GS-2108C Manual de usuario

Ruby Tech

Ruby Tech GS-5116C Manual de usuario

Ruby Tech

Ruby Tech GS-5124C Manual de usuario

Ruby Tech

Ruby Tech GS-5105M Manual de usuario

Ruby Tech

Ruby Tech GS-2116C Manual de usuario

Ruby Tech

Ruby Tech GS-1216L Manual de usuario

Ruby Tech

Ruby Tech PSGS-2112C Manual de usuario

Ruby Tech

Ruby Tech PSES-2126C Manual de usuario

Ruby Tech

Ruby Tech GS-2124C Manual de usuario

Ruby Tech

Ruby Tech GS-1148L Manual de usuario

Ruby Tech

Ruby Tech FGS-2924R Manual de usuario

Ruby Tech

Ruby Tech FGS-2824 Manual de usuario

Ruby Tech

Ruby Tech GS-2224L Manual de usuario

Ruby Tech

Ruby Tech GS-2108C Manual de usuario

Ruby Tech

Ruby Tech RP-1000 Manual de usuario

Ruby Tech

Ruby Tech GS-2216L Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario