RTX RTX4027 Manual de usuario
RTX4027
REPEATER USER GUIDE
Technical Reference Document
Version 1.1
© May-2019 RTX A/S, Denmark
Trademarks
RTX and the combinations of its logo thereof are trademarks of RTX A/S, Denmark.
Other product names used in this publication are for identification purposes and maybe the trademarks of their
respective companies.
Regulatory information United States
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The antenna(s)
used for this transmitter must be used to provide a separation distance of at least 20 cm from all persons.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Regulatory information Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
• This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISEDC radiation exposure limits set forth for an uncontrolled environment.
The antenna(s) used for this transmitter must be used to provide a separation distance of at least 20 cm from all
persons.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences
et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes:
• Cet appareil ne doit pas causer d'interférences.
• Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement
indésirable de l'appareil.
Cet équipement est conforme aux limites d'exposition au rayonnement ISEDC établies pour un environnement non
contrôlé. La ou les antennes utilisées pour cet émetteur doivent être utilisées de manière à assurer une distance de
séparation d'au moins 20 cm de toutes les personnes.
Disclaimer
The contents of this document are provided about RTX products. RTX makes no representations with respect to
completeness or accuracy of the contents of this publication and reserves the right to make changes to product
descriptions, usage, etc., at any time without notice. No license, whether express, implied, to any intellectual property
rights are granted by this publication
Confidentiality
This document should be regarded as confidential, unauthorized copying is not allowed
© May-2019 RTX A/S, Denmark, All rights reserved
http://www.rtx.dk
Contents
1. Introduction:...............................................................................................................................................................5
1.1. Document History ............................................................................................................................................. 5
1.2. What is new.......................................................................................................................................................5
1.3. Main topics........................................................................................................................................................5
2. Installation of Repeater ..............................................................................................................................................6
2.1. Package –Contents/Damage Inspection...........................................................................................................6
2.2. Damage Inspection............................................................................................................................................6
2.3. RTX Base Station Mechanics .............................................................................................................................7
2.4. Mounting the repeater......................................................................................................................................8
3. Recommended external DC adapters......................................................................................................................... 9
4. Repeater registration................................................................................................................................................10
4.1. Register repeater(s) “Local Automatic” ..........................................................................................................10
4.2. Register repeater(s) “Manually” ..................................................................................................................... 11
5. Firmware update: .....................................................................................................................................................14
6. LED and button: ........................................................................................................................................................ 16
1. Introduction:
The RTX4027 repeater user guide is designed to give a detailed overview on how to install, register and manage RTX
repeaters
1.1. Document History
REVISION
AUTHOR
ISSUE DATE
COMMENTS
1.0
HDJ
26-06-2019
1.1
JSK
20-09-2019
Add FCC and IC Regulatory information
1.2. What is new
What new features have been added.
VERSION
FEATURE
V460
1.3. Main topics
•Installation
•Recommended external DC adapters
•Locate automatic registration
•Manual registration
•Firmware update
•LED indications
2. Installation of Repeater
After planning the network, next is to determine the proper places or location the repeater. The repeater should be
mounted as high as possible (2 meters or higher).
2.1. Package –Contents/Damage Inspection
Before Package Is Opened:
Examine the shipping package for evidence of physical damage or mishandling prior to opening. If there is a proof of
mishandling prior to opening, you must report it to the relevant support center of the regional representative or
operator.
Contents of Package:
Make sure all relevant components are available in the package before proceeding to the next step.
Every shipped repeater package/box contains the following items:
1 x Power supply
1 x Repeater
1 x Table stand
1 x Safetysheet
2.2. Damage Inspection
The following are the recommended procedure for you to use for inspection:
1. Examine all relevant components for damage.
2. Make a “defective on arrival – DOA” report or RMA to the operator. Do not move the shipping carton until
the operator has examined it. If possible, send pictures of the damage. The operator/regional representative
will initiate the necessary procedure to process this RMA. They will guide the network administrator on how
to return the damaged package if necessary.
3. If no damage is found, then unwrap all the components and dispose of empty package/carton(s) in
accordance with country specific environmental regulations.
2.3. RTX Base Station Mechanics
The repeaters front end shows an LED indicator that signals different functional states of the repeater.
The indicator is off when the repeater is not powered on.
LED Indicator
Reset Button
DC Power Connector
2.4. Mounting the repeater
There are 2 way to mount the repeater.
1: Use the table stand that is in the box
2: Wall mount the repeater using the screws and anchors
Screws and Anchors needed (Not supplied by RTX)
2x Screws = Screw wall mount M3.5x31
2x Anchors: Length 29,6mm, OD 6,0mm, ID 4,8mm
NOTE: The repeater should be mounted on a wall not higher than 2 meters
3. Recommended external DC adapters
Module number
Specification
Manufacturer
Type
S008ACM0550060
SMPS,100-240VAC,5.5V 600mA, VI
Ten Pao International
LTD
Multi-Plug
(body)
User can use different Adaptor Plug listed below:
Module number
Specification
Manufacturer
Type
8W, VDE
8W, VDE Adaptor Plug
Ten Pao International
LTD
EU Plug
8W, UL
8W, UL Adaptor Plug
US Plug
8W, SAA
8W, SAA Adaptor Plug
AU Plug
8W, BS
8W, BS Adaptor Plug
UK Plug
4. Repeater registration
There are 2 different ways to register RTX repeater’s “Local Automatic” and “Manually”
Local Automatic:
In this mode the repeater registers to the base station with best signal strength, this option is only recommended for
single cell systems and Multi cell systems where the repeater is only able to sync with one specific base station.
Manually:
Manual registration is used in most cases when adding repeaters to a multi cell system. Manual registration allows to
determine what base stations the repeater must connect to.
4.1. Register repeater(s) “Local Automatic”
NOTE: Do not power on the repeaters before they have been added on the base station
NOTE: When adding first repeater the base station(s) will reboot, this is because encryption is being enabled, the
same goes if all repeaters is deleted, then the system will reboot to disable encryption.
Step 1: To register repeater(s), navigate to the Repeater page.
Screen shot
Step 2: Click” Add Repeater” and select “Local Automatic” from the dropdown
Screen shot
Step 3: Give the repeater a name and press “save”
Tabla de contenidos
Otros manuales de Reloj de repetición de RTX
