RPE DIG Series Manual de instalación
“DIG” series controller
Programming instructions
Programmatore_serie_DIG_GB.indd 1 18/07/12 15.06
DESCRIPTION OF DISPLAY AND ICONS
The user interface of the control panel is composed of a liquid crystal display
with dedicated icons, a numerical display and four function keys.
After the battery has been inserted, all the icons on the display are illuminated
for ve seconds to check the correct operation of the LCD; when this check
is completed, the main screen with the clock and battery charge indicator is
displayed (section 2.1).
1.1 USER INTERFACE
Programmatore_serie_DIG_GB.indd 2 18/07/12 15.06
DESCRIPTION OF FUNCTION KEYS
CONFIRM: Used to conrm the selected items or continue with
programming procedures: keep the button pressed until next
screen is displayed.
NEXT: To display next screen or next item, check the main menu or
exit from programming procedures (exit without saving data).
Keep the button pressed until next screen is displayed or the
procedure is completed.
+ : Increase of value in the programming stage
-: Decrease of value in the programming stage
NOTE:
Different functions associated with each key are specied in the detailed description of
the user interface in the following sections.
SERVICE NOTE
1) To cut down the electrical consumption of the control panel (energy saving mode),
the display turns off automatically if no keys are pressed within one minute.
2) To turn on the display press any one of the four keys: the main screen with the clock
and the battery charge monitor are always displayed in the default screen (section 2.1).
Programmatore_serie_DIG_GB.indd 3 18/07/12 15.06
3.5 DIGIT NUMERICAL DISPLAY
The multifunction 3.5 digit numerical display is used to
display the time of day or any other alphanumeric item during
programming.
BATTERY
Displays the battery charged state and is always visible when
the display is on: the icon is active during programming and
in the default screen.
Icon battery on: indicates the battery is charged.
Flashing icon: indicates the battery is at and must be
replaced.
RAIN SENSOR
Displays the status of the outdoor rain sensor (if any) and is
always visible: the icon is active during programming and in
the default screen.
Icon on: indicates that the ground is wet (watering cancelled).
Icon off: indicates the ground is dry (watering enabled).
DESCRIPTION OF ICONS
Programmatore_serie_DIG_GB.indd 4 18/07/12 15.06
HOURGLASS
Used during programming to indicate watering time (in hours
and minutes) is being set.
When the icon starts to ash, together with the irrigator, the
item to be set ashes on the numerical display (hours or
minutes).
ALARM CLOCK
Used during programming to indicate the watering start time
in hours and minutes, and AM or PM mode are being set.
When the icon starts to ash, together with the irrigator, the
item to be set ashes on the numerical display (hours or
minutes or AM/PM).
IRRIGATOR
Used in three different ways: during programming to
indicate the zone which is being programmed, in the manual
procedure to indicate the valve is open or closed, and in the
default screen to indicate that watering is under way.
Irrigator off: valve closed (watering not under way)
Irrigator on: valve open (watering under way)
Irrigator flashing: during programming to indicate the zone
being programmed.
Programmatore_serie_DIG_GB.indd 5 18/07/12 15.06
CLOCK
Used in the programming procedures of the clock and the
weekly calendar to indicate that the time of day, minutes and
the AM or PM modes are being set.
When the clock icon ashes, together with other icons, the
item to be programmed ashes on the numerical display
(hours, minutes, AM/PM or calendar).
CALENDAR
Used in the programming procedures of the clock or watering
programmes to indicate that the weekly calendar is being set.
When the icon ashes in conjunction with the item being
programmed the week day is referenced.
MANUAL
Used in the control procedures of the manual functions.
Icon off: manual functions are not active.
Icon flashing: entry in the procedures described by the
manual.
Programmatore_serie_DIG_GB.indd 6 18/07/12 15.06
PROGRAMMING
Used to create watering programmes.
When the PRG icon ashes, together with other icons, the
item to be programmed ashes on the
numerical display.
After the battery has been installed, all the icons on the display will illuminate
for ve seconds whilst the correct operation of the LCD is being checked.
After ve seconds, the main screen with the clock and battery charge
indicator is displayed and the main menu check is enabled.
After the battery has been installed, all icons
on the display light up in check mode for ve
seconds.
During this stage the function keys are
disabled.
2.1 - MAIN MENU CHECK
DISPLAY FUNCTIONAL CHECK
AM/PM
In the default screen it indicates the time of day.
Icon AM on: it indicates the AM mode
icon PM on: it indicates the PM mode
Programmatore_serie_DIG_GB.indd 7 18/07/12 15.06
After the display check, the main default screen
with the clock is displayed automatically: the
segment (:) between hours and minutes ashes
to indicate that the time count has started.
Use key NEXT to scroll the four functions
available in the main menu: clock preset,
programming, manual and run.
When the icon PRG ashes, use the key
CONFIRM to enter the watering programme
procedure (section 2.3) or NEXT to pass to
the following function (MAN) .
In this screen, the keys +and –are disabled.
MAIN DEFAULT SCREEN
WATERING
PROGRAMMES
When NEXT is pressed, the icon CLOCK
starts to flash: press CONFIRM to enter the
clock programming procedure (section 2.2) or
NEXT to pass to the following function (PRG).
In this screen, the keys +and –are disabled.
PROGRAMMING THE
CLOCK AND WEEKLY
CALENDAR
Programmatore_serie_DIG_GB.indd 8 18/07/12 15.06
When the icon MANUAL ashes, use the
key CONFIRM to enter the manual function
control procedure (section 2.4) or the key
NEXT to pass to the following function (RUN).
In this screen, the keys +and –are disabled.
The RUN indication on the display means that the
control panel is performing an operation cycle.
After two seconds, the main default screen with
clock and battery charge state is displayed.
In this screen, the keys +, –, NEXT and
CONFIRM are disabled.
2.2 - PROGRAMMING THE CLOCK AND THE WEEEKLY CALENDAR
From the main menu it is possible to access the programming procedure of
the clock and weekly calendar.
NOTE: the icons printed in grey indicate that they are blinking. The rain sensor and
the battery icons are on or off according to the actual charged state of the battery and
the ground conditions (wet or dry).
MANUAL FUNCTION
CONTROL
CONTROL PANEL RUN-
NING
Programmatore_serie_DIG_GB.indd 9 18/07/12 15.06
When the icon CLOCK ashes, press
CONFIRM to enter the clock programming
procedure or NEXT to pass to the following
function (PRG).
CONFIRM: enters the clock programming
procedure.
In this screen, the keys +and –are disabled.
When the display of the hours ashes, use
keys [+] and [-] to set the desired value. Press
CONFIRM passes to the following item.
CONFIRM: conrms the value and pass to
the following item (minutes).
NEXT: disabled.
[+] / [-]: increases and decreases the
parameter to be programmed.
When the display of the minutes ashes, use
keys [+] and [-] to set the desired value.
Press CONFIRM to pass to the following item.
CONFIRM: conrms the value and pass to
the following item (PM/AM).
NEXT: disabled.
[+] / [-]: increases and decreases the
parameter to be programmed.
PROGRAMMING THE
CLOCK AND WEEKLY
CALENDAR
PROGRAMMING THE TIME
PROGRAMMING THE
MINUTES
Programmatore_serie_DIG_GB.indd 10 18/07/12 15.06
Tabla de contenidos
