Royal Sovereign RFCI-1826 Manual de usuario
RET Series
2
TABLE OF CONTENTS
TOPIC PAGE
1. INTRODUCTION 3
2. SAFETY PRECAUTIONS 3
3. PRODUCT IDENTIFICATION 5
4. INSTALLATION 6
4.1 Electrical requirements6
4.2 Box contents7
4.3 Assembly8
5. OPERATION11
6. MAINTENANCE 12
7. TROUBLESHOOTING 13
8. SPECIFICATIONS 14
9. WARRANTY 15
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
RET Series
3
1. INTRODUCTION
2. SAFETY PRECAUTIONS
Thank you for choosing a Royal Sovereign trimmer. It has been designed and manufactured to provide
years of continuous service. For complete operating and maintenance information please read this
manual thoroughly. Upon receipt of your trimmer, please inspect the box, the machine and all other
contents for shipping damage. Damage should be brought to the immediate attention of the delivering
carrier (See page 7 for list of shipment elements).
Failure to comply with any of the following safety procedures could result in serious injury. Please read
all instructions carefully and keep for future reference. Royal Sovereign International Inc. cannot be held
responsible for any damages to people, animals or objects due to noncompliance with the safety norms
and recommendations of these documents.
1. Only a licensed electrician should install wiring and outlet for the trimmer.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands away from cutting blade when in operation.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make repairs.
10. Do not attempt to trim items that exceed total recommended material thickness for the unit.
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the blade when in use or place foreign objects inside the machine.
13. Tampering with the protections (rear cover, safety cover, protector plate) and safety devices
is dangerous for the people using the machine and for those exposed to it. Royal Sovereign
International Inc. cannot be held responsible for any damages to people, animals or objects due to
tampering with the protections.
14. Pay attention to the danger notices on the trimmer.
RET Series
4
Dangerous areas and residual risks
All the areas around the machine in which people are at risk of injuries or health problems are
considered dangerous.
Pay close attention to hands when operating the trimmer.
During certain intervention procedures on the machine, which are pointed out each time in this manual,
residual risks for the operator may arise. Residual risks can be avoided by carefully complying with the
procedures of this manual and using the personal protection devices indicated. such as:
manufacturer.
Trimmer should only be operated by trained personnel
DO NOT PLACE HANDS NEAR THE CUTTING BLADE !
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
RET Series
5
3. PRODUCT IDENTIFICATION
9
7
8
12 11 10
5
3
4
6
1
2
NO PART NAME
1 Left Side Cover
2 Power Switch
3 Feed Table Front
4 Fabric Holder Rod
5 Protection Plate
6 Foot Pedal
7 Floor Stand
8 Waste Catcher
9 Right Side Cover
10 Rear Cover
11 Activation Bar
12 Safety Cover
RET Series
6
4. INSTALLATION
Note: The trimmer should be installed by a trained service technician
The trimmer needs to be assembled by a trained installer.
The trimmer should only be used in an area with the following characteristics:
4.1 Electrical requirements
Royal Sovereign recommends that a licensed electrician ensures proper power installation to your trimmer
in accordance with electrical codes in your area.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
RET Series
7
4.2 Box contents
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a
claim is filed with the reseller immediately upon receipt of shipment.
Part Name Quantity Picture
Main
Box
Main Trimmer Assembly 1
Floor Stand Side Frame 2
Floor Stand Cross Bar 1
Owner's Manual 1
Protection Plate (RET-1652/RET-2002)
Protection Plate (RET-2502)
1
2
Wastecatcher Square Bars
2
Fabric Holder Bars 4
Tool
Box
L-wrench (4/6) 1 / 1
5/16 Hexa head bolt (M8*55mm)
Star washer (Ø8.2)
Spring washer (Ø8.2)
10
6
4
5/32 screw (M4*8mm) (RET-1652/2002/2502)
Spring washer (Ø4.1) (RET-1652/2002/2502)
3/4/6
3/4/6
E-ring (Ø8) 8
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
RET Series
8
4.3 Assembly
1. Open the box carton and remove all parts.
2. Open the tool-box. (Fig. 4-1)
This operation must be carried out by a minimum of two people
3. Attach the lower cross bar to the left floor stand side frame and right floor stand side frame using the
supplied screws (M8x55). (Fig. 4-2)
4. Slide the holder rods into the adjacent holes of the assembly in accordance with Fig. 4-3. Using
pinchers, place the E-rings into the appropriate mounting slots of the holder rods. (Fig.4-4)
rear
front
Fig. 4-3 Fig. 4-4
Fig. 4-2
Fig. 4-1
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
RET Series
9
5. Screw the wastecatcher square bars into the previously inserted wastecatcher holder rods, (Fig. 4-5)
putting the supplied screws through the largest drilling in the square bar, so that the head of the screw
sits flush within the bar itself. (Fig. 4-6)
Fig. 4-5 Fig. 4-6
6. Position the main trimmer assembly on top of the floor stand. And properly align the bolt holes. Use
bolts (M8x55) to attach the main trimmer assembly to the floor stand. (Fig. 4-7)
Fig. 4-7
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
RET Series
10
7. Attach the protection plate (Fig. 4-8) to the upper cross bar with the supplied screws. The protection
plate must be assembled on the front part of the upper cross bar, always keeping the table adjustment
pin upward.
Fig. 4-8
8. Connect the power cord in to the AC outlet and turn the Power switch to the ON position.
9. The Trimmer is now ready for Operation. (Fig. 4-9)
Fig. 4-9
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Laminadora de Royal Sovereign
Royal Sovereign
Royal Sovereign RSH-380SL Manual de usuario
Royal Sovereign
Royal Sovereign Alexis 27 Manual de usuario
Royal Sovereign
Royal Sovereign RSC-880LS Manual de usuario
Royal Sovereign
Royal Sovereign RSC-165C Manual de usuario
Royal Sovereign
Royal Sovereign ES-1315 Manual de usuario
Royal Sovereign
Royal Sovereign RSL-2701 Manual de usuario
Royal Sovereign
Royal Sovereign IL-1346W Manual de usuario
Royal Sovereign
Royal Sovereign NR-1201 Manual de usuario
Royal Sovereign
Royal Sovereign RSC-1050CL Manual de usuario
Royal Sovereign
Royal Sovereign RSC-1400C Manual de usuario
Royal Sovereign
Royal Sovereign NB-1900N Manual de usuario
Royal Sovereign
Royal Sovereign EL-9DF Manual de usuario
Royal Sovereign
Royal Sovereign NPH-1200N Manual de usuario
Royal Sovereign
Royal Sovereign RSH-1151 Manual de usuario
Royal Sovereign
Royal Sovereign RSC-1650C Manual de usuario
Royal Sovereign
Royal Sovereign ES-410 Manual de usuario
Royal Sovereign
Royal Sovereign NB-1900N Manual de usuario
Royal Sovereign
Royal Sovereign CS-923 Manual de usuario
Royal Sovereign
Royal Sovereign RSH-380SL Manual de usuario
Royal Sovereign
Royal Sovereign RSL-2701 Manual de usuario
