Rosewill RC-407 Manual de usuario
5/8 Port External Power Gigabit Switch RC407/408
User Manual
5/8 port External Power Gigabit Switch RC407/408 User Manual
2
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received; including interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022
class B for ITE, the essential protection requirement of Council Directive 89/336/EEC on the
approximation of the laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in
this document is not up-to-date. Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without written consent from the
company.
5/8 port External Power Gigabit Switch RC407/408 User Manual
3
Introduction
The device is a powerful, high-performance Gigabit Ethernet switch, with all ports capable of 10, 100
or 1000Mbps auto-negotiation operation (NWay), which means the switch could automatically
negotiate with the connected partners on the network speed and duplex mode. It is ideal for
micro-segmenting large networks into smaller, connected subnets for improved performance,
enabling the bandwidth demanding multimedia and imaging applications. Moreover, the
10/100/1000Mbps auto-sensing ability provides an easy way to migrate 10/100Mbps to 1000Mbps
network with no pain. Compared to the shared 10Mbps or 100Mbps networks, the switch delivers a
dedicated 10/100/1000Mbps connection to every attached client with no bandwidth congestion issue.
This switch also supports auto MDI / MDI-X function. Each port could be used to connect to another
switch or hub with no crossover RJ-45 cable.
Store-and-forward switching mode promises the low latency plus eliminates all the network errors,
including runt and CRC error packets. To work under full-duplex mode, transmission and reception of
the frames can occur simultaneously without causing collisions as well as double the network
bandwidth.
The switch provides 9K bytes jumbo frames, which means the frames size is larger than normal 1.5K.
With the Jumbo frame function, you can get better network performance, because the switch can
send more data at the same time with lower CPU usage.
The switch is plug-n-play without any software to configure and also fully compliant with all kinds of
network protocols.
Before you start to install the switch, check the following contents in this package：
．One Gigabit Ethernet switch
．One external power adapter
．Screws and wall-mount plastic
．User’s manual
5/8 port External Power Gigabit Switch RC407/408 User Manual
4
LED Definition
Please refer to the following table for LED definition
5-Port ( RC407 )
8-Port ( RC408 )
LED Status Operation
Steady Green Power is onPower
Off Power is off
Steady Green Connected as 1000Mbps1000M
Blinking Green The port is transmitting/receiving data.
Steady Green Connected as 100Mbps100M
Blinking Green The port is transmitting/receiving data.
Steady Green Connected as 10Mbps10M
Blinking Green The port is transmitting/receiving data.
Stations Connection
Connect each station to the switch by twisted-pair cable. Plug one RJ-45 connector into a RJ-45 port
of the switch, and plug the other RJ-45 connector into the station’s network adapter. Power on the
switch and then system is ready.
For cable selection, refer to the following table.
Switches Connection
In making a switch interconnection, you could use any port to connect another switch with straight or
crossover cable. As all the ports support auto MDI / MDI-X function, using a straight cable to make a
switch-to-switch connection is allowed.
For cable selection, refer to the following table：
5/8 port External Power Gigabit Switch RC407/408 User Manual
5
Network Speed Cable Type Max.
Length
10Mbps Cat. 3, 4, 5 UTP/STP 100 meters
100Mbps Cat. 5 UTP/STP 100 meters
1000Mbps Cat. 5 UTP/STP 100 meters
Specification
Standard IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x full duplex operation and flow control
Interface 5/ 8* 10/100/1000Mbps RJ-45 Gigabit Ethernet Ports
Uplink Auto MDI/MDI-X（Auto crossover）
Network Speed 10/100/1000Mbps & Full/Half duplex mode auto detection (1000Mbps for Full duplex
only)
MAC Addr.
Ta bl e
8K MAC entries
Buffer Memory 144K byte ( 8-Port Model ) - RC408
112K byte ( 5-Port Model ) - RC407
Jumbo Frame 9K bytes
Power Supply External Power adapter
12VDC 1A
EMI CE and FCC class B
Thank you for purchasing a quality Rosewill Product.
Please register your product at : www.rosewill.com for complete warranty information and future support for your
product.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Rosewill
Rosewill
Rosewill RC-409X Manual de usuario
Rosewill
Rosewill RHUB-200 Manual de usuario
Rosewill
Rosewill RC412 Manual de usuario
Rosewill
Rosewill RHB320 Manual de usuario
Rosewill
Rosewill RHUB120 Manual de usuario
Rosewill
Rosewill RHUB110 Manual de usuario
Rosewill
Rosewill RKV-2P Manual de usuario
Rosewill
Rosewill RC-410X Manual de usuario
Rosewill
Rosewill RC-415 Manual de usuario
Rosewill
Rosewill RFS-105 Manual de usuario
Rosewill
Rosewill RHUB-300 Manual de usuario
Rosewill
Rosewill RGS-1024 Manual de usuario
Rosewill
Rosewill RHB-620 Manual de usuario
Rosewill
Rosewill RGS-108P Manual de usuario
Rosewill
Rosewill RC405 Manual de usuario
Rosewill
Rosewill KVMRKV-4UC Manual de usuario
Rosewill
Rosewill RC-GS1024 Manual de usuario
Rosewill
Rosewill RC-409LX Manual de usuario
Rosewill
Rosewill RHUB-210 Manual de usuario
Rosewill
Rosewill RVHS3-11001 Manual de usuario
