Rosemount 3300 Series Manual de usuario

www.rosemount.com

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009 Rosemount 3300 Series

¢00825-0100-4811I¤

Step 1: Mount the Transmitter Head/Probe

Step 2: Set Jumpers and Switches

Step 3: Connect the Wiring

Step 4: Configure

Exchange the Transmitter Head or Probe

Product Certifications

Start

End

Check Process Connections

Confirm Configuration

Guided Wave Radar Level and Interface

Transmitter

3300_QIG_English_Rev DA.fm Page 1 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009

Rosemount 3300 Series

Emerson Process Management, Rosemount Inc.

IMPORTANT NOTICE

This installation guide provides basic guidelines for the Rosemount®3300 Series. Refer to

Rosemount 3300 Series Reference Manual (Document No. 00809-0100-4811) for more

instructions. The manual and this Quick Installation Guide (QIG) are also available

electronically on www.rosemount.com.

The Americas

Emerson Process Management

8200 Market Boulevard

Chanhassen MN 55317 USA

Tel (USA) 1 800 999 9307

Tel (International) +1 952 906 8888

Fax +1 952 949 7001

Europe, Middle East & Africa

Emerson Process Management

Shared Services Ltd

Heath Place

Bognor Regis

West Sussex PO22 9SH

England

Tel +44 (1243) 863 121

Fax +44 (1243) 867 554

Asia Pacific

Emerson Process Management

Singapore Pte Ltd

1 Pandan Crescent

Singapore 128461

Tel +65 6777 8211

Fax +65 6777 0947

Service Support Hotline: +65 6770 8711

E-mail: Enquiries@AP.EmersonProcess.com

3300_QIG_English_Rev DA.fm Page 2 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009 Rosemount 3300 Series

WARNING

Failure to follow safe installation and service guidelines could result in death or

serious injury

• Make sure only qualified personnel perform installation or service.

• Use the equipment only as specified in this QIG and the Reference Manual. Failure to

do so may impair the protection provided by the equipment.

• Any substitution of non-recognized spare parts may jeopardize safety. Repair, e.g.

substitution of components etc. may also jeopardize safety and is under no

circumstances allowed.

Explosions could result in death or serious injury

• Verify that the operating environment of the transmitter is consistent with the

appropriate hazardous locations specifications. See Product Certifications on page 18

in this Quick Installation Guide.

• In an Explosion-proof/Flameproof installation, do not remove the transmitter covers

when power is applied to the unit.

• Before connecting a HART®-based Communicator in an explosive atmosphere, make

sure the instruments in the loop are installed in accordance with intrinsically safe or

non-incendive field wiring practices.

• To avoid process leaks, only use o-ring designed to seal with the corresponding

flange adapter.

Electrical shock can result in death or serious injury

• Avoid contact with the leads and terminals. High voltage that may be present on leads

can cause electrical shock.

• Make sure the main power to the Rosemount 3300 Series transmitter is off and the

lines to any other external power source are disconnected or not powered while wiring

the transmitter.

Probes with non-conducting surfaces

• Probes covered with plastic and/or with plastic discs may generate an ignition-

capable level of electrostatic charge under certain extreme conditions. Therefore,

when the probe is used in a potentially explosive atmosphere, appropriate measures

must be taken to prevent electrostatic discharge.

3300_QIG_English_Rev DA.fm Page 3 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009

Rosemount 3300 Series

STEP 1: MOUNT THE TRANSMITTER HEAD/PROBE

Tank Connection with Flange

1. Place a gasket on top of the tank flange.

2. Lower the transmitter and probe with flange into

the tank.

3. Tighten the bolts.

4. Loosen the nut that connects the housing to the

probe and rotate the housing to the desired 

direction.

5. Tighten the nut.

Threaded Tank Connection

1. For adapters with BSP/G threads, place a gasket 

on top of the tank flange.

2. Lower the transmitter and probe into the tank.

3. Mount the adapter into the process connection.

4. Loosen the nut that connects the housing to the 

probe and rotate the housing to the desired 

direction.

5. Tighten the nut.



Tri-Clamp Tank Connection

1. Place a gasket on top of the tank flange.

2. Lower the transmitter and probe into the tank.

3. Fasten the probe to the tank flange with a clamp.

4. Loosen the nut that connects the transmitter

housing to the probe slightly.

5. Rotate the transmitter housing so the cable

entries/display face the desired direction.

6. Tighten the nut.

Flange

Probe

Gasket

Tank

Flange

Transmitter

Housing

Nut

Bolt

Adapter

Probe

Tank Flange/

Process

Connection

Nut

Sealant on

threads (NPT)

Gasket (BSP/G)

Gasket

Tank

Probe

Tri-Clamp

Transmitter

Housing

NOTE

For adapters with NPT threads, pressure-tight joints

require a sealant.

Refer to Rosemount 3300 Series Reference Manual (Document No. 00809-0100-4811) for

details regarding the mounting of transmitter head/probe.

3300_QIG_English_Rev DA.fm Page 4 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009 Rosemount 3300 Series

STEP 1 CONTINUED...

Bracket Mounting, on Wall

1. Mount the bracket directly to the wall with screws

suitable for the purpose.

2. Mount the transmitter with probe to the bracket,

and secure the installation with the three supplied

screws.

Bracket Mounting, on Pipe

1. Put the two U-bolts through the holes of the

bracket. Holes are available for both vertical and

horizontal pipe mounting.

2. Put the clamping brackets on the U-bolts and

around the pipe.

3. Fasten the bracket to the pipe using the four

supplied nuts.

4. Mount the transmitter with probe to the bracket,

and secure with the three supplied screws.

See the Rosemount 5300 Series Reference Manual

(Document No. 00809-0100-4530) for more

installation details.

U-bolts

Bracket

Clamping

brackets

Transmitter

housing

Bracket

Probe

Vertical mounting

Transmitter

housing

Transmitter

housing

Probe

Horizontal mounting

Probe

3300_QIG_English_Rev DA.fm Page 5 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009

Rosemount 3300 Series

STEP 2: SET JUMPERS AND SWITCHES

If alarm and security jumpers are not set, the transmitter operates with the default alarm

condition HIGH and Security OFF. 

Write Protection must be set after configuration (Step 4).



To set Alarm and Write Protection on the circuit board:

1. Remove the cover on the circuit side (see label marked 

circuit side).

2. To set the 4-20 mA alarm output to LOW, move the

alarm switch to the LOW position.

3. To enable the security write protection feature, move 

the write protect switch to the ON position.

4. Replace the cover and tighten securely.

To set Alarm and Write Protection on the LCD:

To have the LCD override the circuit board settings, the write

protection switch needs to be in the OFF position, and the alarm

switch needs to be in the HIGH position.

1. To set the 4-20 mA alarm output to LOW, place a 

jumper between the right and center hole position.

2. To enable the security write protection feature, place a 

jumper between the left and center hole position - 

ON.

3300_QIG_English_Rev DA.fm Page 6 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009 Rosemount 3300 Series

STEP 3: CONNECT THE WIRING

For HART®, the input voltage is 11-42 V (11-30 V in IS applications, 16-42 V in

Explosion-proof / Flameproof applications). For Modbus, the input voltage is 8-30 V.

The transmitter requires shielded twisted pair wiring (18-12 AWG) suitable for the supply

voltage, and, if applicable, approved for use in hazardous areas.

To Connect the Transmitter

1. Make sure the housing is grounded according to Hazardous Locations Certifications,

national and local electrical codes.

2. Verify that the power supply is disconnected.

3. Remove the cover on the terminal side (see label marked field terminals).

4. Pull the cable(s) through the cable gland / conduit. For Explosion-proof / Flameproof

installations, only use cable glands or conduit entry devices certified Explosion-proof or

Flameproof.

5. To connect the wires see the illustrations below.

6. If applicable, use the enclosed metal plug to seal any unused port.

7. Replace the cover and tighten.

8. Tighten the cable gland.

9. Connect the power supply.

Non-Intrinsically

Safe HART®

Output

Load Resistance 250 

Power Supply

HART®

Modem

Rosemount 375

Field Communicator PC

Rosemount 3300

Series Transmitter

3300_QIG_English_Rev DA.fm Page 7 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009

Rosemount 3300 Series

STEP 3 CONTINUED...

Intrinsically Safe

HART®Output

Power 

Supply RL

250 

Approved

IS Barrier DCS

Rosemount 3300

Series Transmitter

IS Parameters:

Ui=30 V, Ii= 130 mA,

Pi=1 W, Li=Ci=0 HART®

Modem

Rosemount 375

Field Communicator

Power 

Supply

120 

RS485 Bus

HART + HART -

120 

If the unit is the last

transmitter on the bus,

a 120 termination

resistor is required.

Non-intrinsically

Safe Modbus

Output

3300_QIG_English_Rev DA.fm Page 8 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009 Rosemount 3300 Series

The Rosemount 275 / 375 Handheld Communicator requires a minimum load resistance of

250 Ohm within the loop in order to function properly, see below.

Load Limitations

R ()

U (V)

Non-Hazardous Installations

R ()

U (V)

Explosion-proof/Flameproof (EEx d) Installations

R ()

U (V)

Intrinsically Safe Installations

NOTE

For the EEx d case the diagram

is only valid if the HART®load

resistance is at the + side,

otherwise the load resistance

value is limited to 300 Ohm.

3300_QIG_English_Rev DA.fm Page 9 Friday, August 7, 2009 11:17 AM

Quick Installation Guide

00825-0100-4811, Rev DA

June 2009

Rosemount 3300 Series

STEP 4: CONFIGURE

If the transmitter is pre-configured at the factory, step 4 is only necessary to change or verify

the settings.



Configuration of the Rosemount 3300 Series transmitter can be done either with a

Rosemount 375 Field Communicator, Asset Management Solutions (AMS) or Radar

Configuration Tools (RCT). If using the Radar Configuration Tools, a HART®modem is

required, and the procedure is described below, together with the corresponding 

Rosemount 375 fast key codes.

Installing the Radar Configuration Tools (RCT) Software

To install the RCT software:

1. Insert the installation CD into your CD-ROM drive.

2. Follow the instructions. If the installation program does not automatically start, run

Setup.exe

Starting RCT

Click Programs > Rosemount > RCT, and the following window appears(1).

The Help function of the RCT can be reached from the menu or by pressing the F1 key.

(1) For optimum performance set COM Port Buffers to 1. You might receive a pop-up reminder of this before the

RCT window appears. See Chapter 4 “Start-up” in the Reference Manual (00809-0100-4811).

Wizard

Setup

3300_QIG_English_Rev DA.fm Page 10 Friday, August 7, 2009 11:17 AM

Otros manuales para 3300 Series

Tabla de contenidos

Otros manuales de Transmisor de Rosemount

Rosemount

Rosemount 148 Manual de usuario

Rosemount

Rosemount 248 Manual de usuario

Rosemount

Rosemount 8732 Series Manual de usuario

Rosemount

Rosemount 702 Manual de usuario

Rosemount

Rosemount 3108 Manual de usuario

Rosemount

Rosemount 3051SMV Manual de usuario

Rosemount

Rosemount 2088 Manual de usuario

Rosemount

Rosemount 3051 Manual de usuario

Rosemount

Rosemount 3300 Series Manual de usuario

Rosemount

Rosemount 248 Manual de usuario

Rosemount

Rosemount Oxymitter 4000 Manual de capacitación

Rosemount

Rosemount 3144 Manual de usuario

Rosemount

Rosemount 3244MV Manual de usuario

Rosemount

Rosemount 8732E Manual de usuario

Rosemount

Rosemount FISHER-ROSEMOUNT 244EH Manual de usuario

Rosemount

Rosemount 3107 Manual de instrucciones

Rosemount

Rosemount 3152 Manual de usuario

Rosemount

Rosemount 248 Manual de usuario

Rosemount

Rosemount 2051CF Series Manual de usuario

Rosemount

Rosemount 848T Manual de usuario

Rosemount

Rosemount 3144P Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Rosemount

Rosemount 2051 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario