Rosch Computer G7VP2 Manual de usuario

37330119

G7VP2

Rev. C+

System Board

User’s Manual

This publication contains information that is protected by copyright. No

part of it may be reproduced in any form or by any means or used to

make any transformation/adaptation without the prior written permission

from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any express

or implied warranties of merchantability or fitness for any particular purpose.

The user will assume the entire risk of the use or the results of the use of

this document. Further, the manufacturer reserves the right to revise this

publication and make changes to its contents at any time, without obligation

to notify any person or entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95 and Windows®98

are registered trademarks of Microsoft Corporation. Intel, Pentium

and Pentium with MMX technology are registered trademarks of

Intel Corporation. Cyrix, 6x86L, 6x86MX and M II are registered

trademarks of Cyrix Corporation. AMD, K5, K6, K6-2 and K6-III are

registered trademarks of Advanced Micro Devices, Inc. IBM 6x86MX

is a registered trademark of International Business Machine

Corporation. IDT C6 and WinChip2 are registered trademarks of

IDT Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .............................................................................................

2.2 System Memory.............................................................................................................

2.3 DIP Switch and Jumper Settings of the Processors...................

2.4 Jumper Settings for Clearing CMOS Data..........................................

2.5 Jumper Settings for Power Supply Type...................................................

2.6 Jumper Settings for ATX Power-On/Off Select...............................

2.7 Jumper Settings for SDRAM Clock (DIMM)......................................

2.8 Jumper Settings for Watchdog Timer.........................................................

2.9 Connecting the Ribbon Cables and Wires of the Ports

and Connectors.............................................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Setup....................................................................

3.1.2 BIOS Features Setup..........................................................................

3.1.3 Chipset Features Setup....................................................................

3.1.4 Power Management Setup............................................................

3.1.5 PNP/PCI Configuration....................................................................

3.1.6 Load Fail-Safe Settings......................................................................

3.1.7 Load Optimal Settings......................................................................

3.1.8 Integrated Peripherals.........................................................................

3.1.9 Supervisor Password..........................................................................

3.1.10 User Password.........................................................................................

3.1.11 IDE HDD Auto Detection...........................................................

3.1.12 Save & Exit Setup.................................................................................

3.1.13 Exit Without Saving..............................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface....................................................................

4.2 System Health Monitor Utility..........................................................................

4.3 Drivers...................................................................................................................................

Appendix A - Watchdog Timer

A.1 Using the Watchdog Timer Function.........................................................

Appendix B - Identifying Processors

B.1 Intel Processors.............................................................................................................

B.2 Cyrix Processors..........................................................................................................

B.3 IBM Processors.............................................................................................................

B.4 AMD Processors.........................................................................................................

B.5 IDT Processors.............................................................................................................

Appendix C - System Error Message

C.1 POST Beep.......................................................................................................................

C.2 Error Messages..............................................................................................................

Appendix D - Troubleshooting

D.1 Troubleshooting Checklist.................................................................................... 68

Note:

The user’s manual in the provided CD contains detailed information

about the system board. If, in some cases, some information doesn’t

match those shown in this manual, this manual should always be

regarded as the most updated version.

1Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• VIAApollo 598MVP AGP system chipset

Processor

The system board is equipped with a switching voltage regulator

that supports 2.0V to 3.5V core voltage for various processors.

• AMD®K5 PR90/PR100/PR120/PR133/PR166, K6-166/200/233/

266/300, K6-2/250/266/300/333/350/366/380/400/450/475/

500 or K6-III/400/450/475/500/550

• Intel Pentium90/100/120/133/150/166/200MHz or Intel

Pentiumprocessor with MMXTM technology-166/200/233MHz

• Cyrix®6x86L PR150+/PR166+/PR200+, 6x86MX-PR166/

PR200/PR233/PR266 or M II-200/266/300/333/366/380/400

• IBM® 6x86MX-PR200/PR233/PR266/PR300/PR333

• IDT®C6-180/200/225/240 or WinChip2-200/225/233/240/

266/300

System Memory

The system board supports 16MB to 256MB of memory. It is

equipped with two DIMM sockets. The 168-pin DIMM sockets use

x64 EDO (60/70ns), SDRAM (10/12/13ns) or PC SDRAM (PC-

100 SDRAM for 100MHz external system bus clock processors),

3.3V.

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

16MBx64

Memory Size

16MB

32MB

64MB

128MB

Introduction

Level 2 Cache Memory

• 512KB pipeline burst, direct map write-through cache installed on

the system board.

Expansion Slots

The system board is equipped with 1 dedicated PCI slot, 5

dedicated 16-bit ISA slots and 1 shared PCI/ISA slot. All PCI and

ISA slots are bus masters.

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to Chapter 4 for instructions on

using the DMI utility.

Connectors

• 2 connectors for external USB ports

• 1 connector for IrDA interface

• 2 serial ports

• 1 parallel port

• 2 IDE connectors

• 1 floppy connector

• 1 PS/2 mouse port

• 1 PS/2 or AT keyboard port

• 1 5-pin AT keyboard connector

• 1 20-pin ATX power supply connector

• 1 12-pin standard AT power supply connector

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Ultra DMA/33 supported (Synchronous Ultra DMA mode -

data transfer rate up to a maximum of 33MB/sec.)

• PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

1Introduction

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120, ZIP and SCSI sequential

boot-up

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports infrared peripheral devices that meet the ASKIR or HPSIR

standard.

USB Ports

The system board is equipped with two connectors for external

USB ports. USB allows data exchange between your computer and

a wide range of simultaneously accessible external Plug and Play

peripherals.

BIOS

• Award BIOS, Windows95/98 Plug and Play compatible

• Flash EPROM for easy BIOS upgrades

1.1.2 Intelligence

Monitors Processor Temperature and Overheat Alarm

The system board is able to detect the temperature of the

processor. An alarm will sound in case of processor overheat.

Monitors Processor/Chassis Fan Speed and Failure Alarm

The system board is able to detect the fan speed (RPM-Revolutions

Per Minute) of the processor and chassis fans, and alerts you to

attend to any irregularity that may damage your system.

Monitors Power Voltages and Failure Alarm

The system board is able to detect the output voltage of the power

supply. An alarm will sound warning you of voltage irregularity.

Automatic Fan Control

With the system’s power switched on, the processor’s fan will rotate

only if the temperature of the processor is over 25oC.

Introduction

Dual Function Power Button (ATX power supply only)

Depending on the setting in the BIOS setup, this switch will allow

your system to enter the Soft-Off or Suspend mode.

RTC Timer to Power-on the System (ATX power supply only)

The RTC installed on the system board allows your system to

automatically power-on on the set date and time.

Watchdog Timer

The system board is designed for Industrial PC applications. It

supports the Watchdog Timer function allowing your application to

regularly “clear” the system at the set time interval. If the system

hangs or fails to function, it will reset at the set time interval so that

your system will continue to operate. Refer to “Jumper Settings for

Watchdog Timer” in chapter 2 of this manual for more information.

• 8 step counter (0.5/1/2/4/8/16/32/64 sec)

Virus Protection

Most viruses today destroy data stored in hard drives. The system

board is designed to protect the boot sector and partition table of

your hard disk drive.

1Introduction

1.2 Package Checklist

The system board package contains the following items:

;The system board

;A user’s manual

;Serial, mouse and printer port cables

Option 1:

- One card-edge bracket with a 9-pin and 25-pin serial port

cables

- One card-edge bracket with a 25-pin printer port cable and

a PS/2 mouse port cable

Option 2:

- One card-edge bracket with two 9-pin serial port cables

and a PS/2 mouse port cable

- One 25-pin printer port cable for chassis mounting

;One 40-pin IDE hard disk cable

;One 34-pin floppy disk drive cable

;One CD

One card-edge bracket with two USB ports (optional)

If any of these items are missing or damaged, please contact your

dealer or sales representative for assistance.

Tabla de contenidos

Otros manuales de Placa madre de Rosch Computer

Rosch Computer

Rosch Computer iQ965-IGM Series Manual de usuario

Rosch Computer

Rosch Computer MX3955U Manual de usuario

Rosch Computer

Rosch Computer MB770 Manual de usuario

Rosch Computer

Rosch Computer i910GML-DCQIC9 Manual de usuario

Rosch Computer

Rosch Computer G5M150-N Manual de usuario

Rosch Computer

Rosch Computer ROSCH-Q67FVISA Manual de usuario

Rosch Computer

Rosch Computer G7B630-NRM Manual de usuario

Rosch Computer

Rosch Computer GITOX3 Manual de usuario

Rosch Computer

Rosch Computer CA331-NR Manual de usuario

Rosch Computer

Rosch Computer EMB-M4 Manual de usuario

Rosch Computer

Rosch Computer MS-98A9 Manual de usuario

Rosch Computer

Rosch Computer MS-98H4 Manual de usuario

Rosch Computer

Rosch Computer i910GML-DCQIC6 Manual de usuario

Rosch Computer

Rosch Computer EMB-M2 Manual de usuario

Rosch Computer

Rosch Computer G4V506-P Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario