Ronix 7112 Manual de usuario
7112
ELECTRIC ROUTER
USER MANUAL 1
SPECIFICATIONS
Model 7112
Input Power 1850W
Voltage 220V
Frequency 50Hz
No Load speed 5000-22000/min
Collet chuck capacity 12mm
Accessories
Carbon brush 2pcs Guide holder 1Pc,
straight guide 1pc
Trimmer guide 1 pc templet guide 1pc,
collet sleeve ¼,
Collet sleeve 3/8’ ,Operation Manual 1pc
service book 1pc wrench 1pc
PARTS LIST
Depth Adjustment
Handle
Depth Adjustment
Screw
ON/OFF Switch
Handle
Base Plate
Plastic Dust Shield
Trimmer Guide
Speed Control
Dimmer
ELECTRIC ROUTER
2
- Manufacturer reserves the right to change specifications without notice.
- specifications may differ from country to country.
GENERAL SAFETY RULES (FOR ALL TOOLS)
WARNING:
Read and understand all instructions. Failure to follow all instructions
listed below, may result in electric shock, fire and/ or serious personal
injury.
SAVE THESE INSTRUCTIONS
WORK AREA
1. Keep your work area clean and well it. Cluttered benches and dark
areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep bystander children and visitors away while operating a power
tool. distractions can cause you to lose control
ELECTRICAL SAFETY
4. Power tool plugs must match the outlet. Never modify the plugs in any
way. Do not use any adapter plugs with earthed power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock. do not
change the plug in any way. Double insulation eliminates the need for
the three wire grounded power cord and grounded power supply system.
5. Avoid body contact with grounded surfaces such as pipes, radiators,
ranges and refrigerators. These is a increased risk of electric shock if
your body is grounded.
USER MANUAL 3
6. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord to carry the tools or pull
the plug from an outlet. Keep cord away from heat, oil, sharp edges
or moving parts. Replace damaged cords immediately. Damaged cord
increase the risk of electric shock.
8. When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. these cords are rated for outdoor use and reduce
the risk of electric shock.
PERSONAL SAFETY
9. Stay alert, watch what you are doing and use common sense when
operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating power tools may
result in serious personal injury.
10. Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
11. Avoid accidental starting. Be sure switch is off before plugging in.
carrying tools with your finger on the switch or plugging in tools that have
the switch on invites accidents.
12. Remove adjusting keys or wrenches before turning the tool on. A
wrench or a key that is left attached to a rotating part of the tool may
result in personal injury.
13. Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enables better control of the tool in
unexpected situations.
14. Use safety equipment. Always wear eye protection. Dust mask,
non-skid safety shoes, hard hat, or hearing protection must be used
for appropriate conditions. Ordinary eye or sun glasses are NOT eye
protection.
ELECTRIC ROUTER
4
TOOL USE AND CARE
15. Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or against
your body is unstable and may lead to loss of control.
16. Do not force tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
17. Do not use tool if switch does not turn it on or off. Any tool that
cannot be controlled with the switch is dangerous and must be repaired.
18. Disconnect the plug from the power source before making any
adjucstments, changing accessories, or storing the tool. such preventive
safety measures reduce the risk of starting the tool accidentally.
19. Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
20. Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with sharp cutting edges are less likely to bind and are
easier to control.
21. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tools operation. If
damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
22. Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool, may become
hazardous when used on another tool.
SERVICE
23. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result
in a risk of injury.
24. When servicing a tool, use only identical replacement parts.
Follow instructions in the Maintenance section of the manual. Use of
unauthorized parts or failure to follow Maintenance instructions may
create a risk of electric shock or injury.
USER MANUAL 5
SPECIFIC SAFETY RULES
DO NOT let comfort of familiarity with product (gained from repeated
use) replace strict adherence to router safety rules. If you use this tool
unsafety or incorrectly, you can suffer serious personal injury.
1. Wear hearing protection during extended period of operation.
2. Handle the bits very carefully.
3. Check the bit carefully for cracks or damage before operation. Replace
cracked or damaged bit immediately.
4. Hold tool by insulated gripping surfaces when performing and operation
where the cutting tool may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal parts of the tool “live”
and shock the operator.
5. Avoid cutting nails. Inspect for and remove all nails from the workpiece
before operation.
6. Hold the tool firmly with both hands.
7. Keep hands away from rotating parts.
8. Make sure the bit is not contacting the workpiece before the switch is
turned on.
9. Before using the tool on an actual workpiece, let it run for a while. Watch
for vibration or wobbling that could indicate improperly installed bit.
10. Be careful of the bit rotating direction and the feed direction.
11. Do not leave the tool running. Operate the tool only when hand-held.
12. Always switch off and wait for the bit to come to a complete stop
before removing the tool from workpiece.
13. Do not touch the bit immediately after operation; it may be extremely
hot and could burn your skin.
14. Always lead the power wupply cord away from the tool towards the rear.
15. Do not smear the tool base carelessy with thinner, gasoline, oil or
the like. The may cause cracks in the tool base.
16. Draw attention to the need to use cutters of the correct shank
diameter and suitable for the speed of the tool.
17. Some material contains chemicals which may be toxic. Take caution
ELECTRIC ROUTER
6
to prevent dust inhalation and skin contact. Follow material supplier
safety data.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this instruction
manual may cause serious personal injury.
.SYMPOLS
The following show the symbols used for the tool.
V ----------- Voltage
A ----------- ampere
Hz ----------- hertz
n --------- no load speed.
--/min --------- revolution or reciprocation per minute
--------- class II construction
CAUTION:
- Always be sure that the tool is switched off and unplugged before
carrying out any work on the tool.
.INSTALLING OR REMOVING THE BIT
CAUTION:
- Install the bit securely. Always use only the wrench provided with the
tool. A loose or overtightened bit can be dangerous.
USER MANUAL 7
FUNCTIONAL DESCRIPTION
Stopper pole
Fast-Feed button
Adjusting Bolt
ADJUSTING THE DEPTH OF CUT
1. Place the tool on a flat surface. Loosen the lock lever and lower the
tool body until the bit justtouches the flat surface. Press the lock lever
down to lock the tool body. Now lower the stopper pole until it makes
contact with the adjusting hex bolt. The stopper pole can be moved
rapidly by depressing the fast-feed buton. While pressing the fast-feed
button, raise the stopper pole until the desired depth of cut is obtained.
The depth of cut is equal to the distance between the stopper pole and
the adjusting hex bolt. Stopper pole travel can be checked with the
scale (1mm or 1/16” per graduation) on the tool body. Minute depth
ELECTRIC ROUTER
8
adjustments can be obtained by turning the stopper pole (1.5 mm or
about 1/16” per turn).
2. Now, your predetermined depth of cut can be obtained by loosening
the lock lever and then lowering the tool body until the stopper pole
makes contact with the adjusting hex bolt.
CAUTION:
- Since excessive cutting may cause overload of the motor or difficulty in controlling
the tool, the depth of cut should not be more than 15 mm at a pass when cutting
grooves. When you wish to cut grooves more than 15mm deep, make several passes
with progressively deeper bit settings dangerously.
- Do not tighten the collet nut without inserting a bit or install small shank bits without
using a collet sleeve. Either can lead to breakage of the collet cone.
1. Insert the bit all the way into the collet cone. Press the shaft lock to keep the shaft
stationary and use the wrench to tighten the collet nut securely. When using router
bits with smaller shank diameter, first insert the appropriate collet sleeve into the collet
cone, then install the bit as described (Fig1) above.
2. To remove the bit, follow the installation procedure in reverse
ADJUSTING THE MAIN DEPTH OF CUT
By turning the knob, the upper limit of the tool body can be adjusted.
8
USER MANUAL 9
When the tip of the bit is retracted more than required in relate to the
base plate surface, turn the knob to lower the upper limit.
CAUTION:
- Do not lower the knob too low. The bit will protrude dangerously
.STRAIGHT GUIDE
The straight guide is effectively used for straight cuts when chamfering
or grooving.
9
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Ronix
Ronix
Ronix 3401 Manual de usuario
Ronix
Ronix 4110 Manual de usuario
Ronix
Ronix 1102 Manual de usuario
Ronix
Ronix RA-2702 Manual de usuario
Ronix
Ronix 4150 Manual de usuario
Ronix
Ronix RA-8016 Instrucciones de instalación
Ronix
Ronix 2506V Manual de usuario
Ronix
Ronix 2603 Manual de usuario
Ronix
Ronix 4120 Manual de usuario
Ronix
Ronix RH-4403 Manual de usuario
