Ronix 4110 Manual de usuario
INSTRUCTION MANUAL
JIG SAW
4110
USER MANUAL
SPECIFICATIONS
PARTS LIST
1
Cutting capacity Wood: 130mm, Steel: 10mm
Voltage 220V
Frequency 50HZ/60HZ
Rated power 600W
No- load speed 500-2500RPM
Net Weight 3.0kg
JIG SAW
SAFETY INSTRUCTIONS
WARNING!
WHEN USING ELECTRIC TOOLS, ALL THE SAFETY INSTRUC-
TIONS SHOULD ALWAYS BE OBSERVED TO REDUCE THE
RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY
BEFORE ATTEMPTING TO OPERATE THE TOOL, PLEASE
READ ALL THE INSTRUCTIONS AND SAVE IT FOR FURTHER
REFERENCE.
.BASIC SAFETY PRECAUTIONS FOR ALL ELECTRIC TOOLS
1) Keep work area clean
Cluttered area and benches invite injuries.
2) Consider work area environment
Don’t use electric tools in damp or wet locations. Don’ t expose
electric tools to rain. Keep work area well, In particular, no
inammable liquids or gases must be present.
3) Avoid electric shock.
when you are operating tools, don’t touch metal being grounded,
such as pipe, radiator, freezer, etc.
4) Keep children and visitors away
Don’t let children contact tool or extension cord. All visitors
should be kept away from work place.
5) Store idle tool
when not in use, tools should be stored in dry, high, or locked - up
place.
6) Don’t force tool
It will do the job better and safer at the rate for which it was intended,
Avoid unnecessary overload which may put the operator at risk
and impair functions of the tools.
2
USER MANUAL
7) Use right tool
Don’t force small tools and attachment to do the job of a heavy
duty tool.
Don’t use tools for purpose not intended, for example, don’t use
electric circular saw for cutting logs or tree limbs.
8) Dress properly
Don’t wear loose clothes or jewelry. They can be caught in moving
parts. Rubber gloves and non- skid footwear are recommended
when working outdoors. Wear protective hair covering to contain
long hair.
9) Use safety goggles
Always wear safety goggles. If dust is produced, use the special
masks.
10) Don’t abuse cables
Never carry tool by cable or yank it to disconnect it form socket.
Keep cable from heat, oil and sharp edges.
11) Don’t overreach
Keep proper footing and balance at all times.
12) Maintain tools with care
Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
13) Disconnect tools
when not in use, before servicing, and when changing accessories
such as blades, bits and cutters.
14) Remove adjusting keys wrenches
from the habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
15) Avoid unintentional starting
Don’t carry plugged - in tool with nger on switch. Make sure
3
JIG SAW
switch is off when connecting the plug to the socket.
16) Use extension cord
If an extension cord is required, always check that its cross-
section measurement is equal to or greater then that of the tool
capabilities and so marked.
17) Stay alert
Watch what you are doing. Use common sense. Do not operate
tool when you are tired.
18) Check damaged parts
Before further use of the tool, a guard or other parts that is
damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving part, breakage
of parts, mounting and any other condition that may affect its
operations, A guard or other part that is damaged should be
properly repaired or replaced by a qualied service center unless
otherwise indicated elsewhere in the instruction manual. Have
defective switches replaced by a qualitied service center. Do
not use tool if switch does not turn on and off.
19) Check the voltage
Do not plug the electric tool into the mains until you have
checked that the voltage shown on the data plate corresponds
to the voltage available.
20) Replace parts
The use of improper accessory or attachment other than
recommended present a risk of personal injuries.
21) Have your tool repaired by an expert
This electric tool is in accordance with the relevant safety
regulations. Repairing of electric tool may be carried out only by
expert. Otherwise, it may cause considerable danger of the user.
4
USER MANUAL
.JIG SAW USE
This jig saw is intended for the cutting of wood pieces, steel,
aluminum, plastic with different types of cutting blade.
.ADDITIONAL SAFETY REGULATIONS
1) BEFORE USING THE TOOL, PLEASE CHECK THE SWITCH
IS OFF AND THE PLUG IS NOT CONNECTED TO ELECTRICITY
SOCKET.
2) The tool should not touch any objects when turning on the
tool to avoid any danger.
3) Before plug in the electricity socket, please make sure the
machine is switched off and put the cable on back side.
4) Switch on the tool, then start cutting on work piece.
5) Don’t touch the moving parts especially the blade.
6) Make sure there is no obstacle objective on work piece.
7) Hold the tools tightly when operating the tool.
8) Don’t lay down the tool on the ground or working table before
switch it off.
9) Don’t cut the material with asbestos. When cutting some material
like ber, please wear mask.
10) When switch off the tool, don’t stop the blade by pressing,
Don’t touch the blade by hand because it is quite hot when just
stop working.
11) Only use sharp and indefective blade. The blade must be
replaced if it is broken, with crack, distorted or blunt.
11) If the extended cord need, please use the same type of the
tool.
12) If the working surrounding is too hot, damp or too much
5
JIG SAW
dust, please use an circuit- cut device to assure the safety of
operator.
OPERATION REGULATIONS
.FITTING AND REMOVING A SAW BLADE
NOTE:
Prior to assembly and adjustment, always unplug the tool. This
tool has SDS system for quick and easy changing of saw blade.
.FITTING THE BLADE
- Open the blade holder by fully retracting the blade latch.
- Insert the saw blade into the blade holder, guiding the back of
the blade into the groove of the guide roller.
-Release the blade latch, the blade is assembled well.
.REMOVING THE BLADE
- Release the blade latch, fully retract the blade latch and pull
the blade out of the holder.
6
USER MANUAL
.SAW BLADES INSTRUCTION
The blade is supplied with customers’ requirement. The above
blades may not be supplied with tool.
.SETTING THE PENDULUM ACTION
The four pendulum action settings allow optimum adaptation of
cutting speed, cutting capacity and cutting pattern to the material
being sawed. The pendulum action can be adjusted in four steps
with the adjustment lever. Switching is possible with the machine
running:
7
Blade type Application
Fine- toothed cutting blade For smooth straight cuts
Coarse - toothed cutting blade For fast straight cuts
Metal cutting blade For ferrous and non - ferrous metals
Flush cutting blade For nishing off cuts up to a wall or edge
JIG SAW
.SETTING THE BEVEL ANGLE
The adjustable shoe allows cutting of left hand or Right hand
bevel angles from 0 -45°. The bevel scale has preset positions
at 0° , 15° , 30° , 45°
- RELEASE THE SHOE LEVEL.
- Slide the shoe toward the saw blade.
- Tilt the shoe and set the desired bevel angle by using the scale
- Tighten the shoe lever.
.SWITCHING ON AND OFF
Note: please make sure that the switch is off when the tool plug
into electricity socket.
1) To run the tool, press the on/ off switch.
8
Position Cutting method example
0 no pendulum action Cutting mild steel, stainless steel or plastic,
wood, and plywood
1Small pendulum action Cutting mild steel, Aluminum and hard wood
2Medium pendulum action Cutting wood and plywood, fast Cutting
aluminum and mild steel
3Large pendulum action fast Cutting wood, and plywood
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Ronix
Ronix
Ronix 2603 Manual de usuario
Ronix
Ronix 1102 Manual de usuario
Ronix
Ronix 7112 Manual de usuario
Ronix
Ronix 2506V Manual de usuario
Ronix
Ronix 4150V Manual de usuario
Ronix
Ronix RA-2702 Manual de usuario
Ronix
Ronix 4150 Manual de usuario
Ronix
Ronix RA-8016 Instrucciones de instalación
Ronix
Ronix RH-4403 Manual de usuario
Ronix
Ronix 3401 Manual de usuario
