Ronix 8505 Manual de usuario
LOCK & LOAD 3.6V LI-ION
CORDLESS SCREWDRIVER
8505
USER MANUAL 2
TECHNICAL SPECIFICATIONS
Model 8505
Voltage 3.6V DC
No Load Speed 200RPM
Chuck capacity 6.35mm
Battery 1.5Ah Samsung
Li-Ion
Charge time 3-5Hr
Torque 3N.m
Weight 0.56KG
PART LIST
Chuck
Bit Cartridge
Chamber
Bit Viewer
Window
Bit Loader
Switches Sliding Bit
Loader
Forward/
Reverse
Button
AC
Charging
Port
Red LED Charge
Mode Indicator
On/Off Trigger
LED Work light
Pre-Loaded Bit
Cartridges
CORDLESS SCREWDRIVER
3
WARNING!
For your personal safety, read and understand before using & keep this
instruction manual for future reference.
OPERATING INSTRUCTIONS
Please read the operation instructions meticulously and pay
particular attention to the safety instructions.
CAUTION:
Charging time should not exceed 10-12 hours.
GENERAL SAFETY RULES FOR ALL BATTERY OPERATED
TOOLS
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
.WORK AREA
- Keep your work area clean and well lit. Cluttered benches and dark
areas invite accidents.
- Flammable liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable liquids, gases, or dust.
- Keep bystanders, children, and visitors away while operating a power
tool. Distractions can cause you to lose control.
.ELECTRICAL SAFETY
- Do not abuse the cord.
- Never use the cord to carry the tool.
USER MANUAL 4
- Keep cord away from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords may create a fire.
APPLIES ONLY TO TOOLS WITH A SEPARABLE BATTERY
PACK
- A battery operated tool with integral batteries or a separate battery
pack must be recharged only with the specified charger for the battery.
A charger that may be suitable for one type of battery may create a risk
of fire when used with another battery.
- Use battery operated tool only with specifically designated battery
pack. Use of any other batteries may create a risk of fire.
.PERSONAL SAFETY
- Stay alert, watch what you are doing, and use common sense when
operating a power tool. Do not use tool while tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while operating
power tools may result in serious personal injury.
- Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts.
Loose clothes, jewelry, or longhair can be caught in moving parts.
- Avoid accidental starting. Be sure switch is in the locked or off position
before inserting battery pack. Carrying tools with your finger on the switch
or insetting the battery pack into a tool with the switch on invites accidents.
- Remove adjusting keys or wrenches before turning the tool on. A
wrench or a key that is left attached to a rotating part of the tool may
result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enable better control of the tool in unexpected situations.
- Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
CORDLESS SCREWDRIVER
5
.TOOL USE AND CARE
- Use clamps or other practical way to secure and support the work
piece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
- Do not force tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. A tool that cannot be
controlled with the switch is dangerous and must be repaired.
- Disconnect battery pack from tool or place the switch in the locked
or off position before making any adjustments, changing accessories,
or storing the tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
- Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
- When battery pack is not in use, keep it away from other metal objects
like: paper clips, coins, keys, nails, screws, or other small metal objects
that can make a connection from one terminal to another. Shorting the
battery terminals together may cause sparks, burns, or a fire.
- Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with sharp cutting edge are less likely to bind and are
easier to control.
- Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tool’s operation. If damaged,
have the tool serviced before using. Many accidents are caused by
poorly maintained tools.
- Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool may create a
risk of injury when used on another tool.
SERVICE
- Tool service must be performed only by RONIX PLUS qualified repair
personnel. Service or maintenance performed by unqualified personnel
USER MANUAL 6
may result in a risk of injury.
- When servicing a tool, use only identical replacement parts of RONIX
PLUS after sales service centers.
SAFETY INSTRUCTIONS
WARNING!
When using electric tools, basic safety precautions should always be
followed to reduce the risk of tire, electric shock and personal injury,
including the following. Read all these instructions before attempting to
operate this product and save these instructions.
For safe operations:
1) KEEP WORK AREA CLEAN
- Cluttered areas and benches invite injuries.
2) CONSIDER WORK AREA ENVIRONMENT
- Don’t expose power tools to rain. Don’t use power tools in damp or wet
locations. Keep work area well lit. Don’t use power tools in presence of
flammable liquids or gases.
3) GUARD AGAINST ELECTRIC SHOCK
- Prevent body contact with grounded surfaces (e.g. pipes, radiators,
ranges refrigerators).
4) KEEP CHILDREN AWAY
- Do not let visitors contact tool or extension cord. All visitors should be
kept away from work area.
5) STORE IDLE TOOLS
- When not in use, tools should be stored in dry, high, or locked-up
place, out of the reach of children.
CORDLESS SCREWDRIVER
7
6) DON’T FORCE TOOL
- It will do the job better and safer at the rate for which it was intended.
7) USE RIGHT TOOL
- Don’t force small tools or attachments to do the job of a heavy duty
tool. Don’t use tools for purposes not intended; for example, don’t use
circular saw for cutting tree limbs or logs.
8) DRESS PROPERTY
- Do not wear loose clothing or jewelry. They can be caught in moving parts.
Rubber gloves and non-skid wear recommended when working outdoors.
Wear protective hair covering to contain long hair.
9) USE SAFETY GLASSES
- Also use face or dust mask if cutting operation is dusty.
10. Don’t abuse cord
- Never carry tool by cord or yank it to disconnect it from receptacle.
Keep cord from heat, oil and sharp edges.
11) SECURE WORK
- Use clamps or a vise to hold work is safer than using your hand and it
trees both hands to operate tout.
12) DON’T OVERREACH
- Keep proper footing and balance at all times.
13) MAINTAIN TOOLS WITH CARE
- Keep tools clean for better and safer performance. Follow instructions
for lubricating and changing accessories, inspect tool cords periodically
and if damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep handles dry,
clean and free from oil and grease.
USER MANUAL 8
14) DISCONNECT TOOLS
- When not in use, before servicing, and when changing accessories
such as blades, bits and cutters.
15) REMOVE ADJUSTING KEYS AND WRENCHES
- Form the habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
16) AVOID UNINTENTIONAL STARTING
-Don’t carry plugged-in tool with finger on switch. Be sure switch is off
when plugging in.
17) OUTDOOR USE EXTENSION CORDS
- When tool is used outdoors, use only extension cords intended for use
outdoors and sat marked.
18) STAY ALERT
- Watch what you are doing. Use common sense. Do not operate fool
when you are tired.
19) CHECK DAMAGED PARTS
- Before further use of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard of other part that is
damaged should be properly repaired or replaced by an authorized
service canter unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by an authorized service
center. Do not use tool if switch does not turn it on and off.
WARNING!
- The use of any other accessory or attachment other than recommended
CORDLESS SCREWDRIVER
9
in this operating instruction or the original catalogue may present a risk
of personal injury.
20) HAVE YOUR TOOT REPAIRED BY AN EXPERT
- This electric appliance is in accordance with the relevant salty rules.
Repairing of electric appliances may be carried out only by experts
otherwise it may cause considerable danger for the user.
IMPORTANT CHARGING NOTES
1) Do not store in locations where the temperature may exceed 40ºC.
2) Charge only at ambient temperatures between 4ºC and 40ºC.
3) Charge only using the charger provided with the tool as other chargers
might use different amperages and can damage or destroy your battery
and /or screwdriver
4) Unplug charger before attempting to clean.
5) Do not immerse charger in water or any other liquid.
6) Charging time around 3-5hours
CAUTION:
Never attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return it to a service center
for recycling.
WARNING!
Do not allow liquid to enter charger. Electric shock could result. To
cool the battery pack after use, avoid placing the charger in a warm
environment such as in a metal shed or a non-insulated trailer.
USER MANUAL 10
OPERATION
.CHARGING THE BATTERY
WARNING!
The charger and battery are specifically designed to work together so do
not attempt to use any other devices.
Never insert or allow metallic objects into your charger or battery pack
connections because an electrical failure and hazard will occur.
The charger is designed to use standard household 220volt 50Hz power.
IMPORTANT:
Before using this tool, you must charge the battery.
.CHARGING THE BATTERY
1) The battery needs to be charged before first use.
2) Only after several charge and discharge cycles will the battery attain
and maintain full capacity.
3) The battery may become warm while charging, this is normal and
does not indicate a problem.
4) To charge the battery, plug the output cord of the charger into the AC
power port of the Cordless Screwdriver unit as shown the image;
5) Plug in the charger to the wall outlet and the red light will come on.
Tabla de contenidos
Otros manuales de Destornillador eléctrico de Ronix
