Roland HB-12 Manual de usuario

DSA121

DYX362

Mode indicator

• Light: Press the [Preheat] key to start preheating

• Flashing: Preheating under way

• Off: Preheating completed

Tray

Printer

(BT-12)

Finisher

(This machine HB-12)

Front Cover

Mode Switching

Lever

Time/temperature indicator [Temperature] key [Preheat] key*1 [Power] key

[Time] key [Stop/Unlock] key

Control Panel

Guide to Components of the Finisher

This guide describes the basic printing procedures using the

printer and this machine. In the next pages, the procedures

for each step and particular cautions are explained.

For safe and correct use, be sure to read Safety Information

before using the machine.

Quick Guide

Basic Usage of the Finisher

CAUTION:

• A parent or guardian must be present if infants, children, or people who need assistance use the ma-

chine, and they should be very careful when using it. Otherwise, injury or burns may result.

The finisher has “Standard mode”, “Professional mode”, and “Professional 2 mode”.

◆Standard mode

The factory-default setting is standard mode. The finisher has the following functions

to prevent children from touching the inside of the finisher accidentally when it is very

hot.

• When the inside of the finisher exceeds 70 °C (158 °F), the front cover locks. To

open the front cover, press the [Stop/ Unlock] key for at least 1 second.

The surface of the heater and the fabric are not in contact with each other during the

fixing process, so the surface of the heater does not become dirty.

◆Professional mode

To use this mode, switch from standard mode.

As this mode is for users who are accustomed to using the finisher, the front cover

does not lock even when the temperature of the inside of the finisher exceeds 70 °C

(158 °F).

However, during press processing and fixing processing, the front cover locks regard-

less of whatever mode is used to prevent erroneous operations.

The surface of the heater and the fabric are not in contact with each other during the

fixing process, so the surface of the heater does not become dirty.

◆Professional 2 mode

This mode minimizes the loss of color when T-shirts are washed.

To use this mode, switch from professional mode.

As this mode is for users who are accustomed to using the finisher, the front cover

does not lock even when the temperature of the inside of the finisher exceeds 70 °C

(158 °F).

However, during press processing and fixing processing, the front cover locks regard-

less of whatever mode is used to prevent erroneous operations.

The surface of the heater and the fabric are in contact with each other during the fixing

process, so regular cleaning of the surface of the heater is necessary.

* Refer to Operating Instructions for cleaning frequency and precautions.

◆How to Switch Modes

Press the [Temperature] key and

[Time] key simultaneously for at least

2 seconds.

DYX353

The operating mode changes as fol-

lows.

Standard mode

Professional

2 mode

Professional

mode

DYX354

◆Unlock Cover

When set to standard mode, press

the [Stop/ Unlock] key for at least 1

second.

DYX360

When set to the professional mode,

it is not necessary to hold down the

[Stop/Unlock] key.

Operating Procedure

Perform the procedures in the order of 1, 2, 3, and then 4.

The following settings and procedures are examples for major fabrics.

Depending on your environment, discoloration may occur or the ink may not be fixed prop-

erly. Before configure the settings, check the fixability of the fabric you use.

Fabric type Mode Temperature 1. Preparation 2. Pressing 3. Printing 4. Fixing

T-shirt Standard mode

Professional

mode

170°C (338°F) See next

page.

30sec See BT-12

Operating

Instructions.

3min

Professional 2

mode

180°C (356°F) 30sec 30sec

3min

Tote bag (thick) Standard mode

Professional

mode

170°C (338°F) 30sec 3min

Tote bag (thin) 150°C (302°F) 30sec 3min

Sweatshirts 170°C (338°F) 30sec 3min

Printed in Japan

EN GB EN US EN AU J089-7032

R1-181105 FA01418

Preparation

Loading the fabric in the tray

For details, refer to User’s Guide provided with the printer BT-12.

You can shorten the processing time by putting a garment in the tray while preheating the

finisher.

➊

Press the [Power] key to turn on the power..

➍

Set the amount of time that the heater is on.

Set the time according to the fabric on which you

are printing. The default setting is “Medium”.

➋

Make sure the mode switching lever is set in the

center.

➎

When the [Preheat] key is lit, press the [Preheat]

key to start preheating.

When the [Preheat] key is unlit, no operation is

necessary because preheating is completed.

➌

Set the temperature of the heater.

Set the temperature according to the fabric on which

you are printing. The default setting is “High”

Procedure for ( )

➊

When you move the mode switching lever to the

left, processing starts. An alarm sounds after pre-

heating is completed.

➋

Procedure for ( )

➊

When you move the mode switching lever to the

right, processing starts. An alarm sounds after

preheating is completed.

➋

Otros manuales de Impresora de Roland

Roland

Roland LEC-300 Manual del propietario

Roland

Roland VersaUV LEF2-200 Manual de operación y mantenimiento

Roland

Roland VersaCamm SP-540V Manual de operación y mantenimiento

Roland

Roland TrueVIS VG-640 Manual de usuario

Roland

Roland SOLJET PROIII XC-540 Manual de usuario

Roland

Roland XC-540W Manual de usuario

Roland

Roland SOLJET PRO4 XF-640 Manual de usuario

Roland

Roland VersaUV LEF-200 Manual de usuario

Roland

Roland CAMM-2 PNC-2300 Manual de lista de piezas

Roland

Roland Metaza MPX-90 Manual de usuario

Roland

Roland versaUV lec-540 Manual de usuario

Roland

Roland VersaArt RA-640 Manual de usuario

Roland

Roland Metaza MPX-60 Manual de usuario

Roland

Roland VersaCamm VP-540 Manual de usuario

Roland

Roland CAMM-1 PNC-1610 Manual de usuario

Roland

Roland TrueVIS VF2-640 Manual de usuario

Roland

Roland CAMM-1 PNC-950 Manual de usuario

Roland

Roland PNC-1600 Manual de usuario

Roland

Roland Soljet Pro III XJ-640 Manual de usuario

Roland

Roland CAMM SCRIBE CS-20 Manual de usuario

Roland

Roland Texart XT-640 Manual de usuario

Roland

Roland Metaza MPX-90M Manual de usuario

Roland

Roland VersaUV LEF-20 Manual de uso y cuidado

Roland

Roland Color CAMM PC-50 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario