Rohde & Schwarz FSH4 Manual de usuario

R&S

FSH

Spectrum Analyzer

Operating Manual

1309.6275.12 – 14

Test & Measurement

Operating Manual

The Operating Manual describes the following R&S®FSH models

)R&S FSH4 (1309.6000.04)

)R&S FSH4 (1309.6000.14)

)R&S FSH4 (1309.6000.24)

)R&S FSH8 (1309.6000.08)

)R&S FSH8 (1309.6000.18)

)R&S FSH8 (1309.6000.28)

The manual also covers the following options:

)R&S FSH-K14 (1304.5770.02)

)R&S FSH-K41 (1304.5612.02)

)R&S FSH-K42 (1309.5629.02)

)R&S FSH-K43 (1304.5635.02)

)R&S FSH-K44 (1309.5658.02)

)R&S FSH-K44(E) (1304.5758.02)

)R&S FSH-K45 (1309.5641.02)

)R&S FSH-K46 (1304.5729.02)

)R&S FSH-K46E (1304.5764.02)

)R&S FSH-K47 (1304.5787.02)

)R&S FSH-K47E (1304.5806.02)

)R&S FSH-K50 (1304.5735.02)

)R&S FSH-K50E (1304.5793.02)

)R&S FSH-K51 (1304.5812.02)

)R&S FSH-K51E (1304.5829.02)

The contents of this manual correspond to firmware version 2.00 or higher.

Muehldorfstr. 15, 81671 Munich. Germany

Phone: +49 89 4129-0

Fax: +49 89 4129-12 164

E-mail: info@rohde-schwarz.com

Internet: http://www.rohde-schwarz.com

81671 Munich, Germany

Printed in Germany – Subject to change – Data without tolerance limits is not binding.

R&S®is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

Trade names are trademarks of the owners.

The following abbreviations are used throughout this manual:

R&S®FSH is abbreviated as R&S FSH.

R&S FSH Basic Safety Instructions

Operating Manual 1309.6275.12 - 14 S-1

Basic Safety Instructions

Always read through and comply with the following safety instructions!

All plants and locations of the Rohde & Schwarz group of companies make every effort

to keep the safety standards of our products up to date and to offer our customers the

highest possible degree of safety. Our products and the auxiliary equipment they

require are designed, built and tested in accordance with the safety standards that

apply in each case. Compliance with these standards is continuously monitored by our

quality assurance system. The product described here has been designed, built and

tested in accordance with the attached EC Certificate of Conformity and has left the

manufacturer’s plant in a condition fully complying with safety standards. To maintain

this condition and to ensure safe operation, you must observe all instructions and

warnings provided in this manual. If you have any questions regarding these safety

instructions, the Rohde & Schwarz group of companies will be happy to answer them.

Furthermore, it is your responsibility to use the product in an appropriate manner. This

product is designed for use solely in industrial and laboratory environments or, if

expressly permitted, also in the field and must not be used in any way that may cause

personal injury or property damage. You are responsible if the product is used for any

intention other than its designated purpose or in disregard of the manufacturer's

instructions. The manufacturer shall assume no responsibility for such use of the

product.

The product is used for its designated purpose if it is used in accordance with its

product documentation and within its performance limits (see data sheet,

documentation, the following safety instructions). Using the product requires technical

skills and a basic knowledge of English. It is therefore essential that only skilled and

specialized staff or thoroughly trained personnel with the required skills be allowed to

use the product. If personal safety gear is required for using Rohde & Schwarz

products, this will be indicated at the appropriate place in the product documentation.

Keep the basic safety instructions and the product documentation in a safe place and

pass them on to the subsequent users.

Symbols and safety labels

Observe product

documen-tation

Danger of

electric shock

Warning! Hot

surface PE terminal Ground Ground

terminal

Attention!

Electrostatic

sensitive devices

R&S FSH Basic Safety Instructions

Operating Manual 1309.6275.12 - 14 S-2

Observing the safety instructions will help prevent personal injury or damage of any

kind caused by dangerous situations. Therefore, carefully read through and adhere to

the following safety instructions before and when using the product. It is also absolutely

essential to observe the additional safety instructions on personal safety, for example,

that appear in relevant parts of the product documentation. In these safety instructions,

the word "product" refers to all merchandise sold and distributed by the Rohde &

Schwarz group of companies, including instruments, systems and all accessories.

Tags and their meaning

The following signal words are used in the product documentation in order to warn the

reader about risks and dangers.

indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

indicates the possibility of incorrect operation which can

result in damage to the product.

In the product documentation, the word ATTENTION is used

synonymously.

These tags are in accordance with the standard definition for civil applications in the

European Economic Area. Definitions that deviate from the standard definition may

also exist in other economic areas or military applications. It is therefore essential to

make sure that the tags described here are always used only in connection with the

related product documentation and the related product. The use of tags in connection

with unrelated products or documentation can result in misinterpretation and in

personal injury or material damage.

Operating states and operating positions

The product may be operated only under the operating conditions and in the positions

specified by the manufacturer. If the manufacturer's specifications are not observed,

this can result in electric shock, fire and/or serious personal injury or death. Applicable

local or national safety regulations and rules for the prevention of accidents must be

observed in all work performed.

1. The R&S FSH is protected against dripping water and dust (IP degree 51). Unless

otherwise specified, the following requirements apply to Rohde & Schwarz

products: predefined operating position is always with the housing floor facing

down, IP protection 2X, pollution severity 2, overvoltage category 2, use only in

enclosed spaces, max. operation altitude 4600 m above sea level, max. transport

altitude 12000 m above sea level. A tolerance of ±10% shall apply to the nominal

voltage and of ±5% to the nominal frequency.

R&S FSH Basic Safety Instructions

Operating Manual 1309.6275.12 - 14 S-3

2. Do not place the product on heat-generating devices such as radiators or fan

heaters. The ambient temperature must not exceed the maximum temperature

specified in the product documentation or in the data sheet. Product overheating

can cause electric shock, fire and/or serious personal injury or death.

Electrical Safety

If the information on electrical safety is not observed either at all to the extent

necessary, electric shock, fire and/or serious personal injury or death may occur.

1. Prior to switching on the product, always ensure that the nominal voltage setting on

the power supply matches the nominal voltage of the AC supply network.

2. If the product does not have a power switch for disconnection from the AC supply

network, the plug of the connecting cable is regarded as the disconnecting device.

In such cases, always ensure that the power plug is easily reachable and

accessible at all times (corresponding to the length of connecting cable, approx.

2m). Functional or electronic switches are not suitable for providing disconnection

from the AC supply network. If products without power switches are integrated into

racks or systems, a disconnecting device must be provided at the system level.

3. Never use the product if the power cable is damaged. Check the power cable on a

regular basis to ensure that it is in proper operating condition. By taking

appropriate safety measures and carefully laying the power cable, you can ensure

that the cable will not be damaged and that no one can be hurt by, for example,

tripping over the cable or suffering an electric shock.

4. The product may be operated only from TN/TT supply networks fused with max.

16 A (higher fuse only after consulting with the Rohde & Schwarz group of

companies).

5. Do not insert the plug into sockets that are dusty or dirty. Insert the plug firmly and

all the way into the socket. Otherwise, sparks that result in fire and/or injuries may

occur.

6. Do not overload any sockets, extension cords or connector strips; doing so can

cause fire or electric shocks.

7. For measurements in circuits with voltages Vrms > 30 V, suitable measures (e.g.

appropriate measuring equipment, fusing, current limiting, electrical separation,

insulation) should be taken to avoid any hazards.

8. Ensure that the connections with information technology equipment, e.g. PCs or

other industrial computers, comply with the IEC60950-1/EN60950-1 or IEC61010-

1/EN 61010-1 standards that apply in each case.

9. Unless expressly permitted, never remove the cover or any part of the housing

while the product is in operation. Doing so will expose circuits and components and

can lead to injuries, fire or damage to the product.

10. For permanently installed equipment without built-in fuses, circuit breakers or

similar protective devices, the supply circuit must be fused in such a way that

anyone who has access to the product, as well as the product itself, is adequately

protected from injury or damage.

R&S FSH Basic Safety Instructions

Operating Manual 1309.6275.12 - 14 S-4

11. Use suitable overvoltage protection to ensure that no overvoltage (such as that

caused by a bolt of lightning) can reach the product. Otherwise, the person

operating the product will be exposed to the danger of an electric shock.

12. Any object that is not designed to be placed in the openings of the housing must

not be used for this purpose. Doing so can cause short circuits inside the product

and/or electric shocks, fire or injuries.

13. Unless specified otherwise, products are not liquid-proof (see also section

"Operating states and operating positions", item 1. Therefore, the equipment must

be protected against penetration by liquids. If the necessary precautions are not

taken, the user may suffer electric shock or the product itself may be damaged,

which can also lead to personal injury.

14. Prior to cleaning the product, disconnect it completely from the power supply (e.g.

AC supply network or battery). Use a soft, non-linting cloth to clean the product.

Never use chemical cleaning agents such as alcohol, acetone or diluents for

cellulose lacquers.

Operation

1. Operating the products requires special training and intense concentration. Make

sure that persons who use the products are physically, mentally and emotionally fit

enough to do so; otherwise, injuries or material damage may occur. It is the

responsibility of the employer/operator to select suitable personnel for operating

the products.

2. Before you move or transport the product, read and observe the section titled

"Transport".

3. As with all industrially manufactured goods, the use of substances that induce an

allergic reaction (allergens) such as nickel cannot be generally excluded. If you

develop an allergic reaction (such as a skin rash, frequent sneezing, red eyes or

respiratory difficulties) when using a Rohde & Schwarz product, consult a

physician immediately to determine the cause and to prevent health problems or

stress.

4. Before you start processing the product mechanically and/or thermally, or before

you take it apart, be sure to read and pay special attention to the section titled

"Waste disposal", item 1.

5. Depending on the function, certain products such as RF radio equipment can

produce an elevated level of electromagnetic radiation. Considering that unborn

babies require increased protection, pregnant women must be protected by

appropriate measures. Persons with pacemakers may also be exposed to risks

from electromagnetic radiation. The employer/operator must evaluate workplaces

where there is a special risk of exposure to radiation and, if necessary, take

measures to avert the potential danger.

6. Should a fire occur, the product may release hazardous substances (gases, fluids,

etc.) that can cause health problems. Therefore, suitable measures must be taken,

e.g. protective masks and protective clothing must be worn.

R&S FSH Basic Safety Instructions

Operating Manual 1309.6275.12 - 14 S-5

Repair and service

1. The product may be opened only by authorized, specially trained personnel.

Before any work is performed on the product or before the product is opened, it

must be disconnected from the AC supply network. Otherwise, personnel will be

exposed to the risk of an electric shock.

2.Adjustments, replacement of parts, maintenance and repair may be performed only

by electrical experts authorized by Rohde & Schwarz. Only original parts may be

used for replacing parts relevant to safety (e.g. power switches, power

transformers, fuses). A safety test must always be performed after parts relevant to

safety have been replaced (visual inspection, PE conductor test, insulation

resistance measurement, leakage current measurement, functional test). This

helps ensure the continued safety of the product.

Batteries and rechargeable batteries/cells

If the information regarding batteries and rechargeable batteries/cells is not observed

either at all or to the extent necessary, product users may be exposed to the risk of

explosions, fire and/or serious personal injury, and, in some cases, death. Batteries

and rechargeable batteries with alkaline electrolytes (e.g. lithium cells) must be

handled in accordance with the EN 62133 standard.

1. Cells must not be taken apart or crushed.

2. Cells or batteries must not be exposed to heat or fire. Storage in direct sunlight

must be avoided. Keep cells and batteries clean and dry. Clean soiled connectors

using a dry, clean cloth.

3. Cells or batteries must not be short-circuited. Cells or batteries must not be stored

in a box or in a drawer where they can short-circuit each other, or where they can

be short-circuited by other conductive materials. Cells and batteries must not be

removed from their original packaging until they are ready to be used.

4. Keep cells and batteries out of the hands of children. If a cell or a battery has been

swallowed, seek medical aid immediately.

5. Cells and batteries must not be exposed to any mechanical shocks that are

stronger than permitted.

6. If a cell develops a leak, the fluid must not be allowed to come into contact with the

skin or eyes. If contact occurs, wash the affected area with plenty of water and

seek medical aid.

7. Improperly replacing or charging cells or batteries that contain alkaline electrolytes

(e.g. lithium cells) can cause explosions. Replace cells or batteries only with the

matching Rohde & Schwarz type (see parts list) in order to ensure the safety of the

product.

8. Cells and batteries must be recycled and kept separate from residual waste.

Rechargeable batteries and normal batteries that contain lead, mercury or

cadmium are hazardous waste. Observe the national regulations regarding waste

disposal and recycling.

R&S FSH Informaciones Elementales de Seguridad

Operating Manual 1309.6275.12 - 14 S-6

Transport

1. Handles on the products are designed exclusively to enable personnel to transport

the product. It is therefore not permissible to use handles to fasten the product to

or on transport equipment such as cranes, fork lifts, wagons, etc. The user is

responsible for securely fastening the products to or on the means of transport or

lifting. Observe the safety regulations of the manufacturer of the means of

transport or lifting. Noncompliance can result in personal injury or material

damage.

2. If you use the product in a vehicle, it is the sole responsibility of the driver to drive

the vehicle safely and properly. The manufacturer assumes no responsibility for

accidents or collisions. Never use the product in a moving vehicle if doing so could

distract the driver of the vehicle. Adequately secure the product in the vehicle to

prevent injuries or other damage in the event of an accident.

Waste disposal

1. If products or their components are mechanically and/or thermally processed in a

manner that goes beyond their intended use, hazardous substances (heavy-metal

dust such as lead, beryllium, nickel) may be released. For this reason, the product

may only be disassembled by specially trained personnel. Improper disassembly

may be hazardous to your health. National waste disposal regulations must be

observed.

Informaciones Elementales de Seguridad

Es imprescindible leer y observar las siguientes instrucciones e informaciones

de seguridad!

El principio del grupo de empresas Rohde & Schwarz consiste en tener nuestros

productos siempre al día con los estándares de seguridad y de ofrecer a nuestros

clientes el máximo grado de seguridad. Nuestros productos y todos los equipos

adicionales son siempre fabricados y examinados según las normas de seguridad

vigentes. Nuestro sistema de garantía de calidad controla constantemente que sean

cumplidas estas normas. El presente producto ha sido fabricado y examinado según el

certificado de conformidad adjunto de la UE y ha salido de nuestra planta en estado

impecable según los estándares técnicos de seguridad. Para poder preservar este

estado y garantizar un funcionamiento libre de peligros, el usuario deberá atenerse a

todas las indicaciones, informaciones de seguridad y notas de alerta. El grupo de

empresas Rohde & Schwarz está siempre a su disposición en caso de que tengan

preguntas referentes a estas informaciones de seguridad.

R&S FSH Informaciones Elementales de Seguridad

Operating Manual 1309.6275.12 - 14 S-7

Además queda en la responsabilidad del usuario utilizar el producto en la forma

debida. Este producto está destinado exclusivamente al uso en la industria y el

laboratorio o, si ha sido expresamente autorizado, para aplicaciones de campo y de

ninguna manera deberá ser utilizado de modo que alguna persona/cosa pueda sufrir

daño. El uso del producto fuera de sus fines definidos o sin tener en cuenta las

instrucciones del fabricante queda en la responsabilidad del usuario. El fabricante no

sehace en ninguna forma responsable de consecuencias a causa del mal uso del

producto.

Se parte del uso correcto del producto para los fines definidos si el producto es

utilizado conforme a las indicaciones de la correspondiente documentación del

producto y dentro del margen de rendimiento definido (ver hoja de datos,

documentación, informaciones de seguridad que siguen). El uso del producto hace

necesarios conocimientos técnicos y ciertos conocimientos del idioma inglés. Por eso

se debe tener en cuenta que el producto solo pueda ser operado por personal

especializado o personas instruidas en profundidad con las capacidades

correspondientes. Si fuera necesaria indumentaria de seguridad para el uso de

productos de Rohde & Schwarz, encontraría la información debida en la

documentación del producto en el capítulo correspondiente. Guarde bien las

informaciones de seguridad elementales, así como la documentación del producto, y

entréguelas a usuarios posteriores.

Símbolos y definiciones de seguridad

Ver documen-

tación de

producto

Peligro de

golpe de

corriente

¡Advertencia!

Superficie

caliente

Conexión a

conductor

protector

Conexión a

tierra

Conexión a

masa

conductora

¡Cuidado!

Elementos de

construcción con

peligro de carga

electroestática

Tener en cuenta las informaciones de seguridad sirve para evitar en lo posible

lesiones o daños por peligros de toda clase. Por eso es imprescindible leer

detalladamente y comprender por completo las siguientes informaciones de seguridad

antes de usar el producto, y respetarlas durante el uso del producto. Deberán tenerse

en cuenta todas las demás informaciones de seguridad, como p. ej. Las referentes a la

protección de personas, que encontrarán en el capítulo correspondiente de la

documentación del producto y que también son de obligado cumplimiento. En las

presentes informaciones de seguridad se recogen todos los objetos que distribuye el

grupo de empresas Rohde & Schwarz bajo la denominación de "producto", entre ellos

también aparatos, instalaciones así como toda clase de accesorios.

R&S FSH Informaciones Elementales de Seguridad

Operating Manual 1309.6275.12 - 14 S-8

Palabras de señal y su significado

PELIGRO identifica un peligro inminente con riesgo elevado

que provocará muerte o lesiones graves si no se evita.

ADVERTENCIA identifica un posible peligro con riesgo

medio de provocar muerte o lesiones (graves) si no se evita.

ATENCIÓN identifica un peligro con riesgo reducido de

provocar lesiones leves o moderadas si no se evita.

AVISO indica la posibilidad de utilizar mal el producto y,

como consecuencia, dañarlo.

En la documentación del producto se emplea de forma

sinónima el término CUIDADO.

Las palabras de señal corresponden a la definición habitual para aplicaciones civiles

en el area económica europea. Pueden existir definiciones diferentes a esta definición

en otras áreas económicas o en aplicaciones militares. Por eso se deberá tener en

cuenta que las palabras de señal aquí descritas sean utilizadas siempre solamente en

combinación con la correspondiente documentación del producto y solamente en

combinación con el producto correspondiente. La utilización de las palabras de señal

en combinación con productos o documentaciones que no les correspondan puede

llevar a interpretaciones equivocadas y tener por consecuencia daños en personas u

objetos.

Estados operativos y posiciones de funcionamiento

El producto solamente debe ser utilizado según lo indicado por el fabricante respecto a

los estados operativos y posiciones de funcionamiento sin que se obstruya la

ventilación. Si no se siguen las indicaciones del fabricante, pueden producirse

choques eléctricos, incendios y/o lesiones graves con posible consecuencia de

muerte. En todos los trabajos deberán ser tenidas en cuenta las normas nacionales y

locales de seguridad del trabajo y de prevención de accidentes.

1. El producto solamente debe ser utilizado según lo indicado por el fabricante

referente a la situación y posición de funcionamient. R&S FSH está protegido

contra roción y polvo (modo de protección IP 51). Si no se convino de otra

manera, es para los productos Rohde & Schwarz válido lo que sigue: como

posición de funcionamiento se define por principio la posición con el suelo de la

caja para abajo, modo de protección IP 2X, grado de suciedad 2, categoría de

sobrecarga eléctrica 2, uso solamente en estancias interiores, utilización hasta

4600 m sobre el nivel del mar, transporte hasta 12000 m sobre el nivel del mar. Se

aplicará una tolerancia de ±10 % sobre el voltaje nominal y de ±5 % sobre la

frecuencia nominal.

2. No ponga el producto sobre aparatos que generen calor (p. ej. radiadores o

calefactores). La temperatura ambiente no debe superar la temperatura máxima

especificada en la documentación del producto o en la hoja de datos. En caso de

sobrecalentamiento del producto, pueden producirse choques eléctricos, incendios

y/o lesiones graves con posible consecuencia de muerte.

Otros manuales para FSH4

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Rohde & Schwarz

Rohde & Schwarz

Rohde & Schwarz FSP3 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz TS-PSAM Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S RT-ZC15B Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S FSV3-K106 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S ZNA Series Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S FSP Series Manual de usuario

Rohde & Schwarz

Rohde & Schwarz FPC1000 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S ZN-Z3x Manual de usuario

Rohde & Schwarz

Rohde & Schwarz FPL1003-P4 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz FSW Series Manual de usuario

Rohde & Schwarz

Rohde & Schwarz ZVA24 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz ESW Series Manual de usuario

Rohde & Schwarz

Rohde & Schwarz EVSG1000 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz EVSG1000 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz FSVA3000 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz DVMS4 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S RT-ZC10 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz ZND-K1 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz FPH-26G Manual de usuario

Rohde & Schwarz

Rohde & Schwarz NRT 1080.9506.02/.62 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S NGU Series Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S CMW-KN200 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz RT-ZC30 Manual de usuario

Rohde & Schwarz

Rohde & Schwarz R&S FSW-K106 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario