Rockwell Automation RGU Manual de usuario

Publication 2364F-5.15 - November 1998

EPLACEMENT

NSTRUCTIONS

RGU™ Hub Board Replacement

Contents This document shows how to replace a hub board in a Regenerative

DC Bus Supply Unit (RGU).

What This Kit Contains Using the table below, verify that you have received the appropriate

items in your kit:

Other Items Needed Before you begin, be sure you also have the following:

• Tools needed for:

• Loosening and securing screws

• Measuring voltages

• Documentation:

• Your drive system schematics

• Publication 2364F-5.01, Regenerative DC Bus Supply

Unit (RGU)–User Manual

For this part: You should receive this quantity:

hub communication board 1

ESD wrist strap 1

2RGU™ Hub Board Replacement

Publication 2364F-5.15 - November 1998

Safety Precautions The following general precautions apply when servicing an RGU or a

drive system lineup:

Special Instructions Important: You will need to reuse parts that are removed from the

unit. Place parts, in the order removed, on a clean

surface.

!ATTENTION: Only those familiar with the drive

system, the products used in the system, and the

associated machinery should plan or implement the

installation, startup, and future maintenance of the

system. Failure to comply can result in personal injury

and/or equipment damage.

ATTENTION: Verify that all sources of AC and DC

power are deenergized and locked out or tagged out in

accordance with the requirements of ANSI/NFPA 70E,

Part II.

ATTENTION: Thesystemmaycontainstoredenergy

devices. To avoid the hazard of electrical shock, verify

thatallvoltageoncapacitorshasbeendischargedbefore

attempting to service, repair, or remove a drive system

or its components. You should only attempt the

procedures in this manual if you are qualified to do so

and are familiar withsolid-state control equipment and

the safety procedures in publication NFPA 70E.

ATTENTION: When servicing any unit, do not drop

anynuts,bolts,washers,etc.insidetheunit,astheymay

cause a short circuit on power up.

ATTENTION: This drive system contains ESD

(Electrostatic Discharge) sensitive parts and

assemblies. Static control precautions are required

when installing, testing, or repairing this assembly.

Component damage can result if ESD control

proceduresarenotfollowed. Ifyouarenotfamiliarwith

staticcontrolprocedures,refertoRockwellAutomation

publication8000-4.5.2,GuardingAgainstElectrostatic

Damage or any other applicable ESD protection

handbook.

RGU™ Hub Board Replacement 3

Publication 2364F-5.15 - November 1998

Preliminary Steps Before replacing the hub board, shut off the power; wait five

minutes for voltage to discharge; and open the bay door to the

power structure. Check the board and the wiring for physical

damage (melted copper, burn marks, or damaged components).

Replacing the Hub Board 1. Using a meter, check the voltage across the DC bus terminals

on the power structure, then check for voltage across the

terminals and test points.

2. Put on the ESD wrist strap and connect it one of the door

latches.

3. Mark the cables and sketch the wiring on the illustration

below.

4. Disconnect TB1.

5. Carefully remove the fiber-optic cables from the board (hold-

ing by the connector, not holding by the wire).

6. Pull the board from the standoffs and place the board in an

anti-static bag.

7. Push the new board onto the mounting standoffs.

8. Carefully connect the fiber-optic cables into the appropriate

terminals. Verify the wiring, according to the diagram on the

next page.

9. Plug in TB1 and verify that the terminals are secure.

!ATTENTION: If there is any voltage present,

remove the source of the voltage and check for

voltages again before proceeding to the next step.

TIO#2 TIO#3 TIO#4 TIO#1

U9U7 U8U5 U6U4U3U2 U12 U14 U16 U13

R2R#4R2R#3R2R#2R2R#1

+5V

DGND

TP1

PS OK

TP2

TB1

Hub Communication Board

Sketch Wiring Here

Publication 2364F-5.15 - November 1998

Supersedes Publication 2364F-5.15 - October 1997 P/N 185140

Concluding Steps After installing the board, check for any scrap material or tools in the RGU,

and secure the bay door. Send the old board to Rockwell Automation for

repair; or dispose of the board according to your company’s procedures and

your local ordinances.

R2R TIO

U3 U4 U5 U6

Tx Rx Tx Rx

TIO

R2R#4R2R#3R2R#2R2R#1

U9U7 U8U5 U6U4U3U2 U12 U14 U16 U13

RxRx TxRx TxTxRxTx Tx −Tx Tx Rx

R2R TIO

U3 U4 U5 U6

Tx Rx Tx Rx

R2R TIO

U3 U4 U5 U6

Tx Rx Tx Rx

Master Unit Slave Unit (1) Slave Unit (2)

R2R Communications - Master With Two Slaves

Hub Board

Tabla de contenidos

Otros manuales de Cambiar de Rockwell Automation

Rockwell Automation

Rockwell Automation Allen-Bradley Stratix 2500 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 800F-ALR1 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 802K Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 440G-MZS20SNRJ Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Guard master MC2 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster 440G-LZ Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Guard master 442G-MABH-Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 194U-G3393 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley DeviceNet 800E Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 194E Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 837T-D3 Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Lifeline 4 Guía del usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Stratix 5800 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 440G-EZ Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 194U Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 194U Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 4100-ESRS Guía del usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Stratix 2000 Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 440G-MZS20SNRJE Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 440G-EZS21STL05J Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 194R-NU600-1753 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster F Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Bulletin 802MC Series Manual de usuario

Rockwell Automation

Rockwell Automation STRATIX 8000 1783-MS06T Instrucciones de uso

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario