Rockwell Automation Allen-Bradley SLC 500 BASIC Manual de usuario

SLC 500 BASIC and

BASIC-T Modules

Catalog Numbers 1746-BAS and

1746-BAS-T

User Manual

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application,

Installation and Maintenance of Solid State Controls, publication SGI-1.1,

available from your local Rockwell Automation sales office or online at

http://www.literature.rockwellautomation.com), describes some important

differences between solid state equipment and hard-wired electromechanical

devices. Because of this difference, and also because of the wide variety of

uses for solid state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this

equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for

indirect or consequential damages resulting from the use or application of

this equipment.

The examples and diagrams in this manual are included solely for illustrative

purposes. Because of the many variables and requirements associated with

any particular installation, Rockwell Automation, Inc. cannot assume

responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to

use of information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without

written permission of Rockwell Automation, Inc. is prohibited.

Throughout this manual, when necessary we use notes to make you aware of

safety considerations.

WARNING Identifies information about practices or circumstances

that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful

application and understanding of the product.

ATTENTION Identifies information about practices or circumstances

that can lead to personal injury or death, property

damage, or economic loss. Attentions help you:

•identify a hazard.

•avoid a hazard.

•recognize the consequence.

SHOCK HAZARD Labels may be located on or inside the equipment (for

example, drive or motor) to alert people that dangerous

voltage may be present.

BURN HAZARD Labels may be located on or inside the equipment (for

example, drive or motor) to alert people that surfaces may

be dangerous temperatures.

Publication 1746-UM004B-EN-P - December 2005

Summary of Changes

The information below summarizes the changes to this manual since

the last printing.

To help you find new and updated information in this release of the

manual, we have included change bars as shown to the right of this

paragraph.

SLC, SLC 500, Allen-Bradley, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

For See page

Updated list of related publications P-2

Updated memory module location on circuit board 2-2

Availability of 1747-M3 and 1747-M4 memory modules 3-4

Updated battery location on circuit board 3-1, C-2

Revised JW1 jumper illustration 3-2

Revised JW2 jumper illustration 3-3

Revised JW3 jumper illustration 3-4

Revised JW4 jumper illustration 3-5

Publication 1746-UM004B-EN-P - December 2005

2 Summary of Changes

Notes:

iPublication 1746-UM004B-EN-P - December 2005

Table of Contents

Preface

Who Should Use This Manual . . . . . . . . . . . . . . . . . . . . . . P-1

Purpose of This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . P-1

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . P-2

How to Use This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . P-2

Terms and Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . P-3

Conventions Used in This Manual . . . . . . . . . . . . . . . . . . . P-3

Chapter 1

Module and Development

Software Overview

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

BASIC and BASIC-T Modules. . . . . . . . . . . . . . . . . . . . . . . 1-2

Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Software Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Module Communication Ports. . . . . . . . . . . . . . . . . . . . 1-3

Module LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . 1-4

BASIC Development Software (1747-PBASE) . . . . . . . . . . . 1-5

Typical Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Module Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Module Programming Interface. . . . . . . . . . . . . . . . . . . 1-7

Module Network Configurations . . . . . . . . . . . . . . . . . 1-10

Chapter 2

Component Selection

Memory Requirements for BASIC Programming . . . . . . . . . 2-1

Optional Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Components Required for DH485 Communication . . . . . . . 2-3

Alternate Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

1747-AIC Isolated Link Coupler . . . . . . . . . . . . . . . . . . 2-5

1747-PIC Interface/Converter . . . . . . . . . . . . . . . . . . . . 2-5

DH485 Cable Requirements. . . . . . . . . . . . . . . . . . . . . . . . 2-6

Components Required for DF1 Communication . . . . . . . . . 2-6

Chapter 3

Install and Wire Your Module

Set Module Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Set Jumper JW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Set Jumper JW2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Set Jumper JW3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Set Jumper JW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Install Your module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Wire Your Communication Ports . . . . . . . . . . . . . . . . . . . . 3-9

Wire to Ports PRT1 and PRT2 . . . . . . . . . . . . . . . . . . . . . . 3-9

Hardware Handshaking . . . . . . . . . . . . . . . . . . . . . . . . 3-10

DTE and DCE Overview. . . . . . . . . . . . . . . . . . . . . . . . 3-11

DTE - Data Terminal Equipment. . . . . . . . . . . . . . . . . . 3-11

DCE - Data Communication Equipment . . . . . . . . . . . . 3-12

Wire to Port DH485 . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Publication 1746-UM004B-EN-P - December 2005

ii Table of Contents

Chapter 4

Programming Overview

Understand Module Memory Organization . . . . . . . . . . . . . 4-1

Allocate SLC memory for the Module . . . . . . . . . . . . . . . . . 4-2

Module ID Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

BASIC Programming Instructions . . . . . . . . . . . . . . . . . . . . 4-3

BASIC Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

BASIC Statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

BASIC Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Create and Edit a BASIC Program . . . . . . . . . . . . . . . . . . . 4-8

Enter a BASIC Program Using an ASCII Terminal. . . . . . 4-8

Run a BASIC Program . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Stop a BASIC Program . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Edit a BASIC Program Line Through an ASCII Terminal . 4-11

Delete a BASIC Program Line . . . . . . . . . . . . . . . . . . . . 4-13

Renumber a BASIC Program. . . . . . . . . . . . . . . . . . . . . 4-13

Transfer Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Transfer Data Between the SLC Processor and

Port PRT2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Transfer Data Between the SLC Processor and

Port PRT1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Transfer Data Between the SLC Processor and

Port DH485 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Transfer Data Between the SLC Processor and the

Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Status Information for the SLC Processor. . . . . . . . . . . . 4-19

SLC Fault Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

Appendix A

Specifications

Module Hardware Specifications . . . . . . . . . . . . . . . . . . . . 1-1

1747-PBASE BASIC Development Software Specifications . . 1-3

Related Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Appendix B

Worksheets

Module Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Port PRT1 Configuration (Jumper JW1) . . . . . . . . . . . . . . . B-2

What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Port PRT2 Configuration (Jumper JW2) . . . . . . . . . . . . . . . B-3

What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3

Optional Memory Module Selection (Jumper JW3) . . . . . . . B-4

What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

Program Port and Protocol Selection (Jumper JW4) . . . . . . B-5

What to Do Next . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5

Publication 1746-UM004B-EN-P - December 2005

Table of Contents iii

Appendix C

Lithium Battery Replacement,

Handling, and Disposal

Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Battery Handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Transportation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5

Index

Publication 1746-UM004B-EN-P - December 2005

iv Table of Contents

1Publication 1746-UM004B-EN-P - December 2005

Preface

Read this preface to familiarize yourself with the rest of the manual.

This preface covers the following topics.

•Who should use this manual

•The purpose of this manual

•How to use this manual

•Terms and abbreviations

•Conventions used in this manual

Who Should Use This

Manual

Use this manual if you are responsible for designing, installing,

programming, or troubleshooting control systems that use SLC 500

programmable controllers.

You should have a basic understanding of electrical circuitry and

familiarity with relay logic. If you do not, obtain the proper training

before using this product.

Purpose of This Manual

This manual is a reference guide for the design and installation of the

SLC 500 BASIC and BASIC-T modules. It describes the procedures for

installing and using the modules.

Chapter Title Contents

Preface Describes the purpose, background, and scope of this

manual. Also lists related publications.

1 Module and

Development

Software Overview

Explains the hardware and software features.

2 Component Selection Explains and illustrates how to select memory modules,

network configurations, and modems for your

application.

3 Install and Wire your

Module

Provides installation procedures and wiring guidelines.

4 Programming

Overview

Provides information needed to program your module.

Appendix A Specifications Presents the modules’ specifications.

Appendix B Worksheets Describes how to set the module for proper functioning.

Appendix C Lithium Battery

Replacement,

Handling, and

Disposal

Provides important information for the replacement,

handling, and disposal of lithium batteries.

Publication 1746-UM004B-EN-P - December 2005

2 Preface

Related Documentation

The following documents contain additional information regarding

Rockwell Automation products.

If you would like a manual, you can:

•download a free electronic version from the internet at

www.literature.rockwellautomation.com.

•purchase a printed manual by contacting your local distributor

or Rockwell Automation representative.

How to Use This Manual

To use this manual effectively, use the worksheets provided in

Appendix B. The worksheets can help you document your application

and settings and also facilitate the flow of information to other

individuals in your organization for implementation.

For Read Publication Number

A BASIC language reference manual that describes BASIC

commands, CALLS, and functions

BASIC Language Reference Manual 1746-RM001

A programming manual with detailed instructions on installing and

using BASIC development software to program the BASIC and

BASIC-T module.

BASIC Development Software

Programming Manual

1746-PM001

An overview of the SLC 500 family of products SLC 500 System Overview 1747-SO001

A description of how to install and use a Modular SLC 500

processor

Modular Hardware Style Installation

and Operation Manual

1747-UM011

A reference manual that contains status file data and instruction

set information for SLC 500 controllers

SLC 500 Instruction Set Reference

Manual

1747-RM001

A description of how to install and use a module that acts as a

bridge between DH485 networks and devices requiring DF1

protocol.

DH485/RS-232C Interface Module

User’s Manual

1747-UM005

In-depth information on grounding and wiring Allen-Bradley

programmable controllers

Allen-Bradley Programmable

Controller Grounding and Wiring

Guidelines

1770-4.1

A glossary of industrial automation terms and abbreviations Allen-Bradley Industrial Automation

Glossary

AG-7.1

An article on wire sizes and types for grounding electrical

equipment

National Electric Code Published by the National

Fire Protection Association

of Boston, MA

Otros manuales para Allen-Bradley SLC 500 BASIC

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Rockwell Automation

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix B Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Manual de usuario

Rockwell Automation

Rockwell Automation Reliance Electric LiquiFlo 41L4060 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EWEB Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley SynchLink 1756-SYNCH Manual de usuario

Rockwell Automation

Rockwell Automation ControlLogix 1756-HYD02 Manual de usuario

Rockwell Automation

Rockwell Automation Kinetix 6000 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1441-DYN25-MBAL Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1770-KFC15 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OF4 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley DM2 Guía del usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-OB8EPXT Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1746-HSCE Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Manual de usuario

Rockwell Automation

Rockwell Automation 1794-OB8 Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley EtherNet/IP Manual de usuario

Rockwell Automation

Rockwell Automation Micro800 Series Manual

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Analytics LogixAI Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 1718 Series Manual de usuario

Rockwell Automation

Rockwell Automation AB quality Allen-Bradley 1746-INT4 Manual de usuario

Rockwell Automation

Rockwell Automation 1606-XLERED Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley 800G-XBx-EX Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario