Rocktron Velocity 300 Manual de usuario
1
Instruction Manual
May be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309,
4881047, 4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617.
Other patents pending. Foreign patents pending.
®
HUSH ® is a registered trademark of GHS Corporation
2
Copyright © 2009 GHS Corporation
All Rights Reserved.
Your Velocity®300 has been tested and complies with the following Standards and Directives as
set forth by the European Union:
Council Directive(s): 89/336/EEC Electromagnetic Compatibility
Standard(s): EN55013, EN50082-1
This means that this product has been designed to meet stringent guidelines on how much RF
energy it can emit, and that it should be immune from other sources of interference when properly
used. Improper use of this equipment could result in increased RF emissions, which may or may
not interfere with other electronic products.
To insure against this possibility, always use good shielded cables for all audio input and output
connections. Also, bundle audio cables separately from the AC power cables. These steps will help
insure compliance with the Directive(s).
For more information about other Rocktron products, please see your local dealer or one of our
importers closest to you (listed on the enclosed warranty sheet).
3
CONTENTS
General Safety Precautions 4
1. Introduction 5
2. Velocity 300 Design 6
3. Velocity Front Panel 7
4. Velocity 300 Back Panel 8
5. Operating Precautions 9
6. Automatic Short Detection 10
7. Definition Controls 10
8. Stereo Connection 11
9. Mono/Bridged Connection 12
10. Fuse Replacement 13
11. Specifications 14
4
GENERAL OPERATING PRECAUTIONS
NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO
PROVIDE YEARS OF TROUBLE FREE USE. THIS UNIT REQUIRES CAREFUL
HANDLING.
All warnings on this equipment and in the operating instructions should be
adhered to and all operating instructions should be followed.
Do not use this equipment near water. Care should be taken so that objects do
not fall and liquids are not spilled into the unit through any openings.
The power cord should be unplugged from the outlet when left unused for a
long period of time.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. THIS EQUIPMENT
SHOULD BE SERVICED BY QUALIFIED PERSONNEL ONLY. DO NOT MAKE
ANY INTERNAL ADJUSTMENTS OR ADDITIONS TO THIS EQUIPMENT AT
ANY TIME. DO NOT TAMPER WITH INTERNAL ELECTRONIC COMPONENTS
AT ANY TIME. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY VOID
THE WARRANTY OF THIS EQUIPMENT, AS WELL AS CAUSING SHOCK
HAZARD.
OPERATING TEMPERATURE
Do not expose this unit to excessive heat. This unit is designed to operate
between 32° F and 104° F (0° C and 40° C). This unit may not function properly
under extreme temperatures.
General Safety Precautions
5
1. Introduction
Congratulations on your purchase of the Velocity® 300 guitar power amplifier! Rocktron has been
designing power amplifiers specifically for guitar players since the early 1990's. The Velocity 300 is
the latest and greatest in our line of Velocity power amps.
The Velocity 300 provides 150 watts/channel when used in stereo applications or 300 watts mono
bridged into a 8 ohm load!
The Velocity 300 has a unique “Reactance” circuit that actually replicates the output impedance of tube
amplifiers—so you can get the same great sound that a tube amplifier delivers in a reliable solid state
design. And, because it is a variable control, you can customize your Velocity 300 to sound like any of
your favorite tube amps. Best of all, this feature is available in the mono bridged mode too!
In addition, the Velocity 300 has “Definition” controls to give you that little bit of edge you need to
bring your playing out in the mix. It also has automatic short circuit protection, which detects problems
and shuts down the amplifier before any internal damage can be done.
Other Features:
• 115/230 VAC voltage selector switch.
• An AC power detect circuit, which ensures that the amplifier outputs shut down first when AC is
removed. This will guard against any thumps or pops that could otherwise occur, potentially damaging
speakers when power is cut to the amplifier.
• Differential input buffers to eliminate ground loop hum coming from the power amp.
• Over-temperature protection
• Rock-solid design to provide reliable, trouble-free use.
6
Congratulations on your purchase of the Velocity® 300 guitar power amplifier! The Velocity 300 is
designed to provide the greatest flexibility with the highest reliability, even under extreme operating
conditions. This single rackspace amp will provide 150 watts/channel when used in stereo applications
or 300 watts mono bridged into a 8 ohm load.
The Velocity 300 has a unique “Reactance” circuit that actually replicates the output impedance of tube
amplifiers—so you can get the same great sound that a tube amplifier delivers in a reliable solid state
design. And, because it is a variable control, you can customize your Velocity 300 to sound like any of
your favorite tube amps. Best of all, this feature is available in the mono bridged mode too!
In addition, the Velocity 300 has “Definition” controls to give you that little bit of edge you need to
bring your playing out in the mix.
2. Velocity 300 Design
7
This switch powers up the Velocity 300.
This control determines the volume level for Channel 1.
This control determines the amount of Reactance for Channel 1. As this control is turned clockwise,
the simulated output impedance is increased and the Velocity 300 will increasingly exhibit the
characteristics produced by the interaction between a tube amplifier and a guitar speaker cabinet.
When turned fully counterclockwise, the simulated output impedance is at a minimum.
This control determines the level of DEFINITION for Channel 1. Turning this control fully counter-
clockwise bypasses the Definition circuit, while turning it fully clockwise provides maximum
Definition. See section called "DEFINITION" later in this manual for more information on this
feature.
When switched to “BRIDGED” the Velocity 300 operates as a mono unit with increased output
power (Channel 2 becomes inoperable in this condition). In the "BRIDGED" position the LED
will be "ON". In the “STEREO” position the unit operates as a normal stereo amplifier with 150
watts per channel or side.
This is the "POWER" LED. When the Velocity 300 is "ON" the LED will be lit or "ON".
The MUTE switch allows you to "MUTE" or silence both channels if necessary without turning
off the Velocity 300.
This control determines the volume level for Channel 2.
This control determines the amount of Reactance for Channel 2. As this control is turned clockwise,
the simulated output impedance is increased and the Velocity 300 will increasingly exhibit the
characteristics produced by the interaction between a tube amplifier and a guitar speaker cabinet.
When turned fully counterclockwise, the simulated output impedance is at a minimum.
This control determines the level of DEFINITION for Channel 2. Turning this control fully counter-
clockwise bypasses the Definition circuit, while turning it fully clockwise provides maximum
Definition. See section called "DEFINITION" later in this manual for more information on this
feature.
3. VELOCITY 300 Front Panel
1
2
3
4
5
6
7
8
9
10
8
This standard ¼” jack provides an input to Channel 1 from the output of your preamp or the last device
in your effects chain. This jack is used as the input jack when operating the Velocity 300 in “bridged”
mode.
This standard ¼” jack provides an input to Channel 2 from the output of your preamp or the last device
in your effects chain. Use this jack and Channel 1 input jack when running in stereo.
Note: This jack is inoperable when using the Velocity 300 in “BRIDGED” mode ( BRIDGED
switched to “BRIDGED” and the LED is "ON" on the front panel).
These standard ¼” jacks provide outputs for Channel 1 to speaker cabinets. Do not connect these outputs
to a load of less than 4 ohms (or less than 8 ohms in mono-bridged mode). These jacks are used when
using the Velocity 300 in “BRIDGED” mode.
These standard ¼” jacks provide outputs for Channel 2 to speaker cabinets and are to be used when
running your system in "stereo". Do not connect these outputs to a load of less than 4 ohms (or less than
8 ohms in mono-bridged mode). These jacks are inoperable when using the Velocity 300 in “BRIDGED”
mode.
This switch allows for easy setup between 115VAC and 230VAC.
Warning: Improper setting of this switch may cause the unit to fail. Make sure the switch setting matches
the local AC mains voltage.
This switch allows you to switch between "STEREO" and "BRIDGE" modes. When "STEREO" is
selected the green LED on the front panel will be lit. When "BRIDGE" is selected the red LED on
the front panel will be lit. Select "STEREO" if you would like to run your set up in Stereo. Select
"BRIDGE" if you would like to run your system in mono. Follow the "CONNECTIONS" guide later in
this manual for more information."
This module provides a connection for the power cord and also houses the main fuse of the unit. (For
information about changing the fuse, see page 8).
4. VELOCITY 300 Rear Panel
1
2
3
4
5
6
7
9
Although operation of the Velocity 300 is simple once the proper connections have been made,
attention to the following precautions is essential to protect your equipment against failure and
ensure the long life of your Velocity® amplifier.
Power Output/Speaker Load
The Velocity 300 is capable of producing the following power output levels into each of these
loads:
Unbridged (Stereo)
4 ohm load 150 watts
8 ohm load 75 watts
16 ohm load 37.5 watts (with both channels driven)
Bridged (Mono)
4 ohm load Not Recommended*
8 ohm load 300 watts
16 ohm load 170 watts
! Always be certain to use speakers or speaker cabinets capable
of withstanding the power provided in the above mentioned
applications. Rocktron is not responsible for speaker failure
resulting from use of this equipment.
! Never connect 2 outputs of the amplifier to the same speaker.
This would be equivalent to shorting the outputs of the amplifier
together and would shut the unit down immediately.
5. Operating Precautions
10
A feature truly unique to the Velocity line of power amps is Automatic Short Detection circuitry.
Typically, shorting the outputs of a high output power amplifier will cause amplifier failure and
severely damage internal components. The Automatic Short Detection circuit in the Velocity 250
will automatically detect any shorts which may inadvertently occur across the amplifier’s outputs
and immediately shut down the unit to protect it against internal damage.
Should this condition occur, switch the unit off for approximately 10 seconds and make sure that the
cords from the amplifier outputs are properly connected. When the power is turned on again with
the proper connections, the amplifier will operate normally. It is important to note that two outputs
from the amplifier should never be connected to the same speaker, as this would be equivalent to
shorting the outputs together and will cause the unit to shut down.
In the unlikely event that the proper connections have been made and the unit still shuts down,
we strongly recommend that you first contact our Customer Support Department at the phone or
fax number shown on the back cover of this manual before taking the unit to a dealer or repair
shop for servicing.
6. Automatic Short Detection
When playing with other musicians, it often becomes a problem that the guitar can get “buried”
under the other instruments and cannot be distinguished easily. The front panel Definition control
gives the effect of bringing the guitar out of the cabinet so that it can be heard despite the other
instruments. Although it does not actually effect the volume of the amplifier, the Definition control
can be adjusted so that the guitar becomes more audible when playing with a band. Turning the
Definition control fully counterclockwise bypasses the definition circuit, while turning it fully
clockwise provides maximum definition.
7. Definition Controls
Tabla de contenidos
Otros manuales de Amplificador de Rocktron
Rocktron
Rocktron PROGAP ULTRA Manual de usuario
Rocktron
Rocktron Rampage Bass 15 Manual de usuario
Rocktron
Rocktron VooDu Valve Online Manual de usuario
Rocktron
Rocktron Velocity 100 Manual de usuario
Rocktron
Rocktron Blue Thunder Manual de usuario
Rocktron
Rocktron Velocity V30R Manual de usuario
Rocktron
Rocktron Prophesy II Manual de usuario
Rocktron
Rocktron ACOUSTIC Manual de usuario
Rocktron
Rocktron Chameleon 2000 Manual de usuario
Rocktron
Rocktron Velocity V50C Manual de usuario
Rocktron
Rocktron Gainiac 2 Manual de usuario
Rocktron
Rocktron Velocity V30D Manual de usuario
Rocktron
Rocktron Taboo ARTIST Manual de usuario
Rocktron
Rocktron Vendetta VP4 Manual de usuario
Rocktron
Rocktron PIRANHA Manual de usuario
Rocktron
Rocktron ValveSonic Black Plate+ Manual de usuario
Rocktron
Rocktron Rampage Bass 20 Manual de usuario
Rocktron
Rocktron RA30DSP Manual de usuario
Rocktron
Rocktron PRO G.A.P. Manual de usuario
Rocktron
Rocktron Vendetta Manual de usuario
