ROBLIN Cylindre Centrale Manual de usuario

Libretto di Istruzioni

Instructions Manual

Manuel d’Instructions

Bedienungsanleitung

Cylindre Centrale

Instructions Manual

INDEX

RECOMMENDATIONS AND SUGGESTIONS....................................................................................................................16

CHARACTERISTICS............................................................................................................................................................17

INSTALLATION....................................................................................................................................................................19

USE.......................................................................................................................................................................................23

MAINTENANCE....................................................................................................................................................................24

Manuel d’Instructions

SOMMAIRE

CONSEILS ET SUGGESTIONS ..........................................................................................................................................26

CARACTERISTIQUES.........................................................................................................................................................27

INSTALLATION....................................................................................................................................................................29

UTILISATION........................................................................................................................................................................33

ENTRETIEN..........................................................................................................................................................................34

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages resulting

from incorrect or improper installation.

• The minimum safety distance between the cooker top and the extrac-

tor hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply guaran-

tees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum

diameter 120 mm. The route of the flue must be as short as possible.

• Do not connect the extractor hood to exhaust ducts carrying combus-

tion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances

(e.g. gas burning appliances), a sufficient degree of aeration must be

guaranteed in the room in order to prevent the backflow of exhaust

gas. The kitchen must have an opening communicating directly with

the open air in order to guarantee the entry of clean air.

USE

• The extractor hood has been designed exclusively for domestic use to

eliminate kitchen smells.

• Never use the hood for purposes other than for which it has ben de-

signed.

• Never leave high naked flames under the hood when it is in operation.

• Adjust the flame intensity to direct it onto the bottom of the pan only,

making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use: over-

heated oil can burst into flames.

• The hood should not be used by children or persons not instructed in

its correct use.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carry-

ing out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

650 mm min.

CHARACTERISTICS

Dimensions

Components

Ref. Q.ty Product Components

11 Hood Body, complete with: Controls, Light, Blower,

Filters

21 Chimney Upper

7.1 1 Telescopic frame complete with extractor, consisting of:

7.1a 1 Upper frame

7.1b 1 Lower frame

81 Air Outlet Grill

91 Reducer Flange ø150-120 mm

10 1 Damper

14 1 Hood Body AirOutlet Extension Piece

14.1 1 Air Outlet Connection Extension

14.2 1 Air Outlet Extension

15 1 Air Outlet Connection

25 2 Pipe clamps

Ref. Q.ty Installation Components

11 4 Wall Plugs ø 10

12f 4 Screws M6 x 10

12g 4 Screws M6 x 80

12h 4 Screws 5,2 x 70

21 1 Drilling template

22 4 6.4 mm int. dia washers

23 4 M6 nuts

Q.ty Documentation

1 Instruction Manual

12h

7.1

12g

7.1a

7.1b

14.1

14.2

12f

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

DRILLING THE CEILING/SHELF

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the

template is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert

the Dowels 11 supplied).

• For wooden beam ceilings, drill according to the wood screws used.

• For wooden shelf, drill ø 7 mm.

• For the power supply cable feed, drill ø 10 mm.

• For the air outlet (Ducted Version), drill according to the diameter of the external air ex-

haust duct connection.

• Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• for Cavity ceiling with inner space, with wall thickness of approx. 20 mm, Screws 12h,

supplied.

• For wooden beam ceilings, use 4 wood screws (not provided).

• For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided.

FIXING THE FRAME

• Unfasten the two screws fastening the upper chimney

stack 2.1 to the frame, and remove the chimney from

the upper stack.

If you wish to adjust the height of the frame, proceed as

follows:

• Unfasten the four safety screws located at the top in

the frame separation area. (A)

• Unfasten the eight metric screws joining the two col-

umns, located at the sides of the frame. (B)

• Adjust the frame to the height required, then replace

all the screws removed as above.

• To guarantee greater stability in the frame, replace

the four safety screws in the last hole available.

• Insert the upper chimney stack from above, and leave

it running free on the frame.

• Lift the frame up, making sure that the index over the

frame plate is turned backwards.

• Fit the frame slots onto the two screws inserted in the

ceiling as above, and turn until reaching the centre of

the adjustment slot.

• Tighten the two screws and fasten the other two

screws provided; before locking the screws com-

pletely, it is possible to adjust the frame by turning it,

making sure that the screws do not come out of their

housing in the adjustment slot.

• The Frame must be securely fastened so as to support

both the weight of the Hood and the stress caused by

occasional axial pressure against the fitted Appliance.

After fixing, make sure that the base is stable even

when the Frame is subjected to lateral stress.

• If the Ceiling is not strong enough in the area where

the hood is to be fixed, the Installer must strengthen

the area using suitable plates and counterplates an-

chored to resistant structures.

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to

the chimney using either a flexible or rigid pipe ø 150

or 120mm, the choice of which is left to the installer.

To install a ø 150

• To install the dumper 10

• Fix the pipe in position using sufficient pipe clamps

(not supplied).

To install a ø 120

• To install a ø 120 mm air exhaust connection, insert

the reducer flange 9 on the dumper 10.

• Fix the pipe in position using sufficient pipe clamps

(not supplied).

• Remove any activated charcoal filters.

ø 120ø 150

10 10

Recirculation version air outlet connection

• Insert reducer flange 9on the extractor outlet.

• Push fit the extension piece 14 onto the flange.

• Push fit connector 15 onto the extension piece.

• Insert extension piece 14.2 laterally on connector 15,

ensuring that the outlet is in line with the chimney in-

take.

14.2

Fitting the Upper Chimney and the Hood Body

• Position the upper chimney stack and . x the top of it to the

frame using 2 of the screws removed as above.

• Open the lighting unit by pulling on the notch, disconnect it

from the hood canopy by sliding out the pin.

• Remove the filters one at a time by pushing them towards the

back of the group and pulling down at the same time.

• Remove the activated charcoal filters, if fitted.

• In order to fix the hood body to the frame insert the 4 screws

12f in their seats. It is necessary to leave at least 4-5 mm gap

between the screw heads and the frame plate.

• Hook the hood canopy to the frame and turn it to the left until

it reaches the stop, then lock the screws immediately to prevent

the hood canopy from falling out accidentally.

Recirculation version

• Make sure that the outlet of the extension piece 14.2 is hori-

zontally and vertically aligned with the chimney outlet.

• If this is not the case, remove the lower Chimney Stack and

adjust the position of Extension 14; replace the elements as de-

scribed above.

• Insert Connector Extension 14.1 sideways into Extension 14.2.

• Fit the directional grill 8 into the housing provided. Also make

sure that it is properly fitted into connector 14.1.

14.1

ELECTRICAL CONNECTION

• Connect the Hood to the mains power supply, inserting a two-

pole cut-out switch with contact aperture of at least 3 mm

along the line.

• Ensure that the supply cable connector is properly inserted into

the Suction device socket

• Hook up the Commands connector Cmd.

• Hook up the Spotlights connector Lux to the socket provided

behind the lighting unit cover.

• For the Recirculation Version, fit the Activated Charcoal

Odour Filter.

• Replace the filters and the lighting unit.

Cmd

Lux

Tabla de contenidos

Idiomas:

Otros manuales de Campana de ventilación de ROBLIN

ROBLIN

ROBLIN SMART CUBE 600 Guía

ROBLIN

ROBLIN GRAPHIC 900 Guía del usuario

ROBLIN

ROBLIN Aqua 1200 Inox Manual de usuario

ROBLIN

ROBLIN UNIVERS 900 MURALE Guía del usuario

ROBLIN

ROBLIN 330.0559.005 Manual de usuario

ROBLIN

ROBLIN PROFIL MURALE 900 Manual

ROBLIN

ROBLIN Tiroir 612 Manual de usuario

ROBLIN

ROBLIN VIMEA Manual de usuario

ROBLIN

ROBLIN APOLLON Manual de usuario

ROBLIN

ROBLIN Escale Centrale Manual de operación

ROBLIN

ROBLIN DIVA 900 S Manual de usuario

ROBLIN

ROBLIN GRAPHIC MURALE 900 Manual de usuario

ROBLIN

ROBLIN MISTRAL 800 Guía del usuario

ROBLIN

ROBLIN WINDY PRO 900 Manual de operación

ROBLIN

ROBLIN ATRIUM VERRE 1200 Guía del usuario

ROBLIN

ROBLIN IKOS MURALE Guía

ROBLIN

ROBLIN PALMA 900 Guía del usuario

ROBLIN

ROBLIN HYPNOSE 800 VERTICALE Manual de usuario

ROBLIN

ROBLIN ESPACE 1200 CENTRALE Guía del usuario

ROBLIN

ROBLIN CUBE 600 MURALE Guía

ROBLIN

ROBLIN VENUS 800 VERRE NSM Manual de usuario

ROBLIN

ROBLIN PROFIL 900 Guía del usuario

ROBLIN

ROBLIN ATRIUM Asymetrique Murale Manual de operación

ROBLIN

ROBLIN PILOT MASTER PRO Guía

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario