Robertshaw RS6000 Manual de usuario

Thank you for purchasing a Robertshaw RS6000 programmable

thermostat. This user’s manual will guide you through the setup of the

RS6220C two stage and the RS6320C three stage* thermostats. The

thermostat should already be mounted and correctly wired. The default

settings will enable the thermostat to operate efficiently. Before making

any changes to the schedule read the section on Default Settings.

Features

• Pop-Up Wizard

• Automatic changeover

• Circulating Fan

• Worry-Free memory retention

• Easy change battery

• Large back lit display

• Filter change reminder

• Low battery indicator

• Fahrenheit and Celsius displays

• Dual power

• Adjustable 1st stage temperature differential: 0.5 °F to 3.0 °F (0.5 °C to

1.5 °C)

• Accuracy within ±1 °F

• Universal staging on multi-stage units

• Keypad security lockout

• 4 events per day for heating and cooling

• Individual day scheduling

• User settable Hi and Lo temperature limits

RS6220C

RS6

20C

352-00146-001 Rev B

USERS MANUAL

* Three stage heating available for heat pump applications only.

Application

The Robertshaw RS6000C family of thermostats is designed to control

gas, electric, oil, heat pump, and millivolt heating and electric cooling

systems. The RS6220C is a two stage thermostat and the RS6320C

can support three stages of heating and two stages of cooling in heat

pump applications.

The RS6000C thermostats can have a schedule programmed for

each day.

IMPORTANT SAFETY INFORMATION

WARNING:

• Always turn off power at main fuse or circuit breaker panel before

installing, removing, cleaning, or servicing thermostat.

• Read all the information in this manual before installing

this thermostat.

• This is a 24V AC low-voltage thermostat. Do not install on voltages

higher than 30V AC.

• All wiring must conform to local and national building and electrical

codes and ordinances.

• Do not short (jumper) across terminals on the gas valve or at the

system control to test installation. This will damage the thermostat

and void the warranty.

• Do not connect ground to any terminal in this unit.

• This thermostat is configured with automatic compressor protection

to prevent damage because of short cycling or extended power

outages. Short cycle protection provides a delay between heating

and cooling cycles on heat pumps.

Detailed mounting and wiring instructions are explained in the

Installation Manual.

Refer to the Pop-Up Wizard section in the installation manual for a

complete list of factory defaults and contractor settings.

Providing Power to the Thermostat

For wiring diagrams refer to the Installation Manual.

The thermostats will operate using 24V AC or two AA batteries. When

the two AA batteries are installed the thermostat will continue to run if

the 24V AC fails.

Installing or Changing the Batteries

To remove the battery compartment gently

squeeze the ribbed edges on both sides.

The battery compartment will pull down

from the thermostat body and will detach.

Install two AA batteries following the polarity

as shown inside the compartment. Place

compartment back into the thermostat.

When the batteries are low the thermostat will

enter a low battery mode.

Low battery mode has two levels.

• LEVEL 1: The low battery icon will be displayed. The

thermostat will continue to operate. Replace the

batteries as soon as possible

• LEVEL 2: The low battery icon will flash. If 24V AC

is present the thermostat will continue to operate if

the batteries are discharged or removed. If 24V AC

is not present the thermostat runs on batteries only

and THE SYSTEM WILL NOT OPERATE. Replace

batteries immediately.

Replace batteries if leaving thermostat unattended for more than

30 days.

The clock will continue to run for 10 minutes when the batteries

are removed.

Display Description

The thermostat display will show information that is being used during

operation or programming. This illustration shows all of the display’s

possibilities with an explanation.

1. Event Names (used for editing schedule).

2. Day is displayed on Idle screen. Also used to display day ranges

when editing the schedule (e.g., SAT SUN for weekend).

3. Used with clock to display hold duration (e.g., FOR 2h).

4. On when running a schedule.

5. Used with setpoint.

6. Used along with clock for service reminders (e.g., CHECK HP).

7. Used for time, current setpoint, and some configuration data (e.g.,

filter hours).

8. HVAC mode and status. Icons blink when active. A is for Auto, 2 is

for second stage, E is for emergency.

9. Indicates when security is active.

10.Low battery indicator.

11.Not used.

12.Used for ambient temperature and configuration data (e.g., first

stage differential, F or C, etc.).

13.Fan status (rotates when active).

14.Fan mode selected by pressing FAN button.

12 11

Schedule Settings – Defaults

This thermostat is preprogrammed with a schedule designed to help

lower energy usage year-round.

The default schedule settings are:

Time Cooling °F Heating °F

Morn 6:00 am 78 70

Day 8:00 am 85 62

Eve 6:00 pm 78 70

Nite 10:00 pm 82 62

User Settings – Defaults

During any program changes the display returns back to the operating

display if a button has not been pushed in 10 seconds.

The temperature scale is set to Fahrenheit.

Night light is on.

The first stage differential is 1 °F.

The second stage differential is 2 °F.

The second stage delay is 20 minutes.

Third stage delay is 20 minutes.

Auto changeover is enabled.

Auto changeover deadband is 3 °F.

Filter reminder length is off.

Temperature offset is 0 degrees.

The HI heat limit is 90 °F (32 °C).

The LO cool limit is 45 °F (7 °C)

The operation mode is OFF.

The fan setting is Auto.

The keypad has no password protection.

Refer to the pop up wizard section in the installation manual for a

complete list of factory defaults and contractor settings.

Emergency Heat

Your system may include Emergency Heat. The RS6320C thermostat has

an emergency heat capability for multi stage heat pump systems. To

determine if your system is capable of using emergency heat contact

your contractor. Use the button to enter the EMER mode. An E will

be displayed with the Heat symbol. This mode is used to bypass the heat

pump when it needs servicing or when it cannot keep up with the heat

demand.

Auto Changeover

Auto changeover is the ability of the thermostat to switch automatically

between heating settings and cooling settings. This is useful in Spring

and Fall when the days are warm and the nights are cool. In heat mode

if the room continues to warm beyond a set threshold the thermostat

switches to the cool mode and the associated cooling settings. The

reverse is also true.

As the room temperature changes, the thermostat will call for heating

or cooling as needed. To prevent the heating and cooling systems from

overriding each other, an auto changeover deadband is used.

The deadband is the minimum temperature swing before changing from

heating to cooling or vice versa. The larger the deadband the more the

room temperature will vary.

Operating the Thermostat

Any setting can be changed when it is flashing by pushing or

If a button is not pushed for 10 seconds the thermostat returns

to operation.

The following buttons can be accessed from the front panel.

START/STOP SCHEDULE: Switches between running a schedule and

manual (permanent override). Cancels a temporary override.

EDIT SCHEDULE: Use this button to start editing the schedule. Push

repeatedly to move through the selections.

SELECT: Used to select the days that the new schedule will be copied to.

SET TIME: Sequences through the hour, minute and day.

LIGHT BAR: Turns on the display back light for 10 seconds.

FAN: Turns fan to AUTOMATIC, CIRCULATE or ON.

UP ARROW: Raises the setpoint or increases flashing item.

DOWN ARROW: Lowers the setpoint or decreases flashing item.

HEAT/COOL: Toggles through OFF, HEATING, COOLING, and AUTO. If

configured as HP then emergency heat is also displayed.

Setting Time and Day

To adjust the time and day settings press the SET TIME button. The hour

will flash. If a button is not pushed in 10 seconds the thermostat returns

to operation. To change the settings:

1. Use the and buttons to change the flashing number.

2. Press the SET TIME button to move through hour, minutes and day

of week.

3. Make changes as needed. They will be saved automatically.

NOTE: The thermostat will not correct for Daylight Saving Time.

The thermostat will now function properly using the default schedule.

Changing the Schedule Settings

This thermostat can operate using a single setpoint by overriding

the schedules. If you will be using this thermostat for single setpoint

operation skip to Overriding the Schedule.

The chart below represents one day’s programming schedule. To make

programming your thermostat quicker and easier, recreate the table

for each day of the week on a separate piece of paper, and refer to it

while programming.

Press START/STOP SCHEDULE at any time to exit and save your settings.

Push START/STOP SCHEDULE. The display will show a day flashing at

the top. If a button is not pushed in 30 seconds the thermostat returns

to normal operation.

Use the or to change the hour of the start time if desired.

Push EDIT SCHEDULE to move to minutes.

Use the or to change the minutes of the start time if desired.

Push EDIT SCHEDULE to move to the heat or cool temperature setting.

Use the or to change the temperature setpoint.

Push EDIT SCHEDULE to move to the other setpoint.

Use or to change the temperature setpoint.

NOTE: Pressing will switch between cooling and heating setpoints.

Pressing Set Time button will switch back to the event time.

NOTE: The heating and cooling setpoints CANNOT be entered as

crossed. That is, the cooling setpoint CANNOT BE lower than the

heating setpoint.

Push EDIT SCHEDULE and repeat this process for the remaining

three settings.

After a single day setting is complete pressing EDIT SCHEDULE will enter

into a copy program. To skip the copy program and move to the next day,

press EDIT SCHEDULE and repeat the above steps.

Time Cool Heat

Morning

Day

Evening

Nite

To begin selecting days for the copy program, use and to

highlight each day of the week. If the highlighted day should use the

same schedule, press SELECT to turn on that day. Once all the days that

will use this schedule are selected, press EDIT SCHEDULE. The settings

will be copied to the selected days.

If there are more days to program, the next unprogrammed day will be

blinking. Repeat the steps above until all days have been programmed.

When finished press START/STOP SCHEDULE or wait 30 seconds and the

thermostat will return to operation.

Changing the User Settings

When and are pressed at the same time the thermostat will

display the current settings in order.

To change any setting:

When the setting is visible and flashing press the or arrows

to adjust the number on the screen.

To exit the changes and save:

Press START/STOP SCHEDULE. The thermostat will return

to operation.

SCAL = Scale in °F (Fahrenheit) or °C (Celsius).

CLOC = Set clock to 12 or 24 hour format.

LITE = Display backlight always on ”y” or off ”n”. Also called the

nightlight feature. If the thermostat has been wired with 24V AC (R

and C terminals) then this feature will be displayed and the setting

can be changed.

DIFF = The differential keeps the thermostat from turning on for small

changes in temperature. When in Fahrenheit the range is 0.5

to 3.0 Degrees. In Celsius the range is 0.5 to 1.5 Degrees. The

differential is factory set at 1.0 °F (0.5 °C). This means that

whenever the room temperature is more than 1 °F (0.5 °C) different

from the set temperature the system will turn on. If the system is

turning on too often, increase the differential setting. Note that a

larger differential will mean the room temperature changes more

before the system turns on.

DIF2 = Second Stage Differential = Operates with the first stage to

control a second heating/cooling system. This number will be

added to the first stage differential (See: Two Stage Systems). If

the first stage is running too often lower the settings. This will

turn the second stage on to help the first stage. If both stages are

coming on too often then increase this setting to delay the second

stage.

DLY2 = Second Stage Delay = This timer starts when the first stage turns

on. It resets when the first stage turns off. If this timer runs out the

second stage will turn on (See Two Stage Systems).

DLY3 = Third Stage Delay = This timer starts when the second stage turns

on. It resets when the second stage turns off. If this timer runs

out the third stage will turn on. (See Three Stage Systems).

Auto changeover enable = Makes the auto changeover mode available.

When chosen, the thermostat can automatically switch between

heating and cooling. Note that the High and Low setpoint limits

are not enforced in auto changeover mode.

DEDB = Deadband for auto changeover = the number of degrees that the

room temperature can move away from the active setpoint until

heating or cooling is called for. The larger the deadband the more

the room temperature will vary. This can be from heat to cool or

cool to heat.

HI = High Heat Limit = This is the highest allowed heating setpoint. The

user will not be allowed to set a schedule setpoint or override

temperature higher than this value.

NOTE: High Heat Limit is not enforced in auto changover mode.

LO = Low Cool Limit = This is the lowest allowed cooling setpoint. The

user will not be allowed to set a schedule setpoint or override

temperature lower than this value.

NOTE: Low Cool Limit is not enforced in auto changover mode.

CHECK = Timer to remind the home owner to maintain the filter. Default

setting is off. The timer runs when the system is on. It can be

set at 0 (OFF) or up to 9900 hours. When the time expires CHECK

FLTR is displayed. Press the and buttons to restart the

filter timer.

CYCL = Cycle Timer allows a compressor to rest between cycles. Can be

set from 0 to 5 minutes in 1 min increments.

WARNING: A wrong short cycle setting can

damage your equipment. This should only

be changed by a trained HVAC professional.

CAL = Calibration offset. Changes the displayed temperature from the

actual temperature by +3 to -3 degrees in one degree increments.

Increasing the offset by +2 will cause the thermostat to display

a temperature that is 2 degrees higher than the actual room

temperature

Creating a Password – Protect the Settings

The buttons on the front of the thermostat can be locked with a password.

To create a password:

1. Press the and buttons at the same time and hold them in for

5 seconds.

You will be asked for a 4 digit password.

2. Each digit is set using the and buttons. Press the to

move to the next digit and to save the password after the 4th digit is

entered. Press to move back.

3. The password is saved after 5 seconds.

All of the front buttons are now locked out until the password is entered.

Pressing any button will cause to flash.

To unlock the buttons:

1. Push and hold the and buttons for 5 seconds until the

request for password is displayed.

2. Enter the digits for the password by pressing the and

buttons. Press the to move to the next digit and to save the

password after the 4th digit is entered. Press to move back.

3. When the correct password is set, wait for 5 seconds to unlock

the system.

4. If the wrong password is entered the display will flash ---- for 5

seconds then return to normal.

Once the security has been disabled, a password needs to be recreated

to protect the settings.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Robertshaw

Robertshaw

Robertshaw 9420 Manual de usuario

Robertshaw

Robertshaw 9915i Manual de usuario

Robertshaw

Robertshaw 7700 Manual de usuario

Robertshaw

Robertshaw RS4220C Manual de usuario

Robertshaw

Robertshaw RS3110 Series Manual de usuario

Robertshaw

Robertshaw RS4110 Manual de usuario

Robertshaw

Robertshaw RS4110 Manual de usuario

Robertshaw

Robertshaw Smart Sense SMART 1000 Manual de usuario

Robertshaw

Robertshaw 9520 Manual de usuario

Robertshaw

Robertshaw 300-224 Especificaciones técnicas

Robertshaw

Robertshaw RS2210 Series Manual de usuario

Robertshaw

Robertshaw 8406 Manual de usuario

Robertshaw

Robertshaw 9415 Manual de usuario

Robertshaw

Robertshaw 9415 Manual de usuario

Robertshaw

Robertshaw 9801I Manual de usuario

Robertshaw

Robertshaw RS9210 Manual de usuario

Robertshaw

Robertshaw 8625 Manual de usuario

Robertshaw

Robertshaw 9720 Manual de usuario

Robertshaw

Robertshaw 7610 Manual de usuario

Robertshaw

Robertshaw RS9110 Manual de usuario

Robertshaw

Robertshaw RS9320T Manual de usuario

Robertshaw

Robertshaw 9555 Manual de usuario

Robertshaw

Robertshaw RS2110C Series Manual de usuario

Robertshaw

Robertshaw 8425 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario