RLH Industries RLH 5 Port Manual de usuario

!RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.ﬁberopticlink.com!Page 1

R2012A-0621

Speciﬁcations subject to change without notice.

Contents

_________________________Introduction !1

__________________________Key Features!1

_________________General Safety Practices!2

____________Special Handling Requirements!2

____________________________Acronyms!3

__________________________Applications!3

__________________________Installation !3

_______________________LED Indicators !4

______________________Troubleshooting !5

__________________Ordering Information !5

_________________________Speciﬁcations!5

___________________________Warranty !6

_____________________Technical Support !6

RLH 5 Port SlimLine DIN Mount Ethernet Switch

RLH 5 Port

Hardened Ethernet Switch

SLIMLINE DIN MOUNT

Introduction

The RLH 5 Port SlimLine Ethernet switch is a hardened,

DIN mountable switch that supports 10/100M Ethernet.

The switch is housed in a rugged aluminum alloy

enclosure that requires only 32mm of rack space. The

RLH 5 port Ethernet switch is an ideal solution for

industrial Ethernet applications that require temperature

hardened durability. It features convenient port status

LEDs, auto negotiation and auto MDI/MDI-X.

Key Features

• Ideal for critical, high voltage, remote, or un-manned

locations that must remain operating 24/7/365

• IEEE 802.3 10Base-T UTP and 100Base-TX

• RJ45 UTP ports with 10/100M auto-negotiation

• MDI-II/MDI-X auto detection

• Convenient port status LED indicators

• Environmentally hardened to operate in -40˚F to +185˚F

(-40˚C to +85˚C) environments

• Uses a local 12~36VDC power source

• Standard 35mm DIN rail mount

• Covered by our Exclusive Unconditional Lifetime Warranty

The leader in

rugged ﬁber optic

technology.

Unconditional

Lifetime Warranty

USER GUIDE

RLH Industries, Inc.

General Safety Practices

Intended Audience

This guide is intended for use by knowledgeable telco/network installation, operation and repair

personnel. Every effort has been made to ensure the accuracy of the information in this guide is accurate.

However, due to constant product improvement, specifications and information contained in this

document are subject to change without notice.

Conventions

Symbols for notes, attention, and caution are used throughout this manual to provide readers with

additional information, advice when special attention is needed, and caution to prevent injury or

equipment damage.

The equipment discussed in this document may require tools designed for the purpose being described.

RLH recommends that service personnel be familiar with the correct handling and use of any installation

equipment used, and follow all safety precautions including the use of protective personal equipment as

required.

Caution - Severe Shock Hazard

• Never install during a lightning storm or where unsafe high voltages are present.

• Copper network wires may carry high DC voltages. Use caution when handling copper wiring.

Warning

The intra-building port(s) of the equipment or subassembly is suitable for connection to intrabuilding or

unexposed wiring or cabling only. The intra-building port(s) of the equipment MUST NOT be metallically

connected to interfaces that connect to the OSP or its wiring. These interfaces are designed for use as

intra-building interfaces only (Type 4 ports as described in GR-1089-CORE, Issue 4) and require isolation

from the exposed OSP cabling. The addition of Primary Protectors is not sufficient protection in order to

connect these interfaces metallically to OSP wiring.

Special handling requirements

Be careful when handling electronic components

ATTENTION

ELECTROSTATIC

SENSITIVE

DEVICES

• This product contains static sensitive components.

• Do not open the enclosure, there are no user serviceable parts.

• Follow proper electrostatic discharge procedures.

This product utilizes circuitry that can be damaged by static electricity. Before installing, discharge static

electricity on your body by physically making contact with earth ground. Failure to follow ESD precautions

may cause damage to the unit and prevent proper operation.

Page 2!!!RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.ﬁberopticlink.com

Acronyms

Commonly used acronyms and abbreviations

Acronym/Abbreviation

Description

UTP

Unshielded Twisted Pair (commonly used in Ethernet networks)

Twisted Pair (same as UTP)

PWR

Power

LED

Light Emitting Diode

GRN

Green

Applications

Network equipment used in critical applications demand rugged, reliable Ethernet switches for

uninterrupted service. RLH hardened, industrial switches are ideal for small and medium enterprise, retail,

commercial and telecommunications applications where reliability is a concern.

Commonly, switches are used to intelligently manage data packets between ports. A typical Ethernet

switch installation diagram is shown below.

10/100M LINK/ACT

PWR

ETHERNET SWITCH

RLH Ethernet Switch

12~36VDC Power Supply

Network

Ethernet

Devices

Ethernet

Upper Level Switch/Network Device

Typical Ethernet Switch Diagram

Installation

Prior to installation:

• Check for shipping damage

• Check the contents to ensure correct model and ﬁber type

• Have a clean, dry, DIN rail or wall mount installation environment ready

Required for installation:

•12~36VDC local power source

!RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.ﬁberopticlink.com!Page 3

Connect Ethernet cable

The 10/100/Base-T copper connection is made via the RJ45 ports. The TP ports are auto-negotiating and

require no additional settings.

Connect Power

Attach a FG ground wire to the ground screw on the housing. Alternately, attach a ground wire to the FG

terminal on the power connector. Connect a local 12~36VDC power supply to the power input terminals.

Note: The power terminals are polarity sensitive. Attach the Positive DC wire to the V+ terminal.

LED Indicators

10/100M LINK/ACT

PWR

ETHERNET SWITCH

10/100M LINK/ACT

PWR

ETHERNET SWITCH

10/100M LINK/ACT

PWR

ETHERNET SWITCH

Indicator

Color

LED

Description

PWR

GRN

PWR

GRN

10/100M

GRN

10/100M

GRN

LINK/ACT

GRN

LINK/ACT

GRN

LINK/ACT

GRN

System power is present

OFF

System power is disconnected

TP port speed is 100M

OFF

TP port speed is 10M

Established network connection

Blinking

TP port activity

OFF

No network connection established

Page 4!!!RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.ﬁberopticlink.com

Troubleshooting

If trouble is encountered, verify all copper and fiber connections. Refer to the LED Indicators on of the

unit. They show availability of power, modes of operation, and data being received by the fiber and TP

ports.

If trouble persists, replace the unit and retest. If technical assistance is required, contact the RLH

Industries, inc. technical support department:

800-877-1672 (6 am to 6 pm- PST),

or call our 24/7 Technical/Customer Service: (714) 366-2503 or (714) 457-5740

Ordering Information

RLH Ethernet PoE products are available directly through RLH Industries, Inc. or its distributors

nationwide.

RLH Part Number

Description

Powering Require-

ment

RLH-ES5U-1

RLH 5 Port DIN Mount 10/100M Ethernet Switch

24VDC Local Power

Please contact your RLH sales representative for pricing and delivery information

General Specifications

Protocols

100BASE-TX, 10BASE-T

Standards

IEEE802.3x, IEEE802.3,IEEE802.3U

Processing Type

Store and Forward, with IEEE802.3x full duplex, non-blocking ﬂow control

Flow Control

IEEE802.3x ﬂow control, back pressure ﬂow control

Mac Address

Forward and Filtrate Rate

14810pps

System Exchange

Bandwidth

4.8G

Copper Connector

RJ45 UTP, 10/100BaseT(X) auto negotiation speed, Full/half duplex mode, and auto MDI/MDI-

X connection, 1000V protection isolation

RJ45 UTP, 10/100BaseT(X) auto negotiation speed, Full/half duplex mode, and auto MDI/MDI-

X connection, 1000V protection isolation

Copper distance

100m / 328 feet

LED Indicators

100

TP port speed - ON: 100m, OFF: 10M

LED Indicators

PWR

Power - ON: power applied, OFF: no power

Power Input

24VDC (12~36VDC) 300mA

Overload Current

Protection

1.1A

Dimensions

W3.0” x H4.0” x D1.25” (78mm x 103mm x 32mm)

Weight

350g

Housing

Aluminum alloy, IP30 protection

Temperature

Operating

-40˚F to +158˚F (-40˚C to +70˚C)

Temperature

Storage

-40˚F to +176˚F (-40˚C to +80˚C)

Humidity

5~95% non-condensing

!RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.ﬁberopticlink.com!Page 5

Warranty

RLH is recognized throughout the world and offers the only UNCONDITIONAL LIFETIME WARRANTY

in the industry. We are very proud of our warranty which simply states that the product is warranted to be

free of defects in material and workmanship for the LIFE OF THE PRODUCT.

• We believe our customers shouldn't have to incur additional costs due to failure or damage

• We engineer our products with total confidence in our quality

• We understand how safety and reliability impact the total cost of ownership

• We know that customer support extends beyond the initial sale, so we stand behind our products

RLH will replace any product, or part thereof, that fails FOR ANY REASON, provided the defective part is

returned to RLH Freight prepaid. This warranty is UNCONDITIONAL and valid even when RLH products

have been abused or mishandled, or the product has been damaged as a result of a natural disaster. This

warranty will reduce your costs and simplify your maintenance activities. Not all RLH products are covered

by this warranty.

To make a warranty claim, or schedule repair or replacement of your RLH product, please

returns must have an RMA number before we can receive any items.

Technical Support

Normal technical support hours

(Mon - Fri 6am - 6pm PST)

Local (714) 532-1672

Toll Free (800) 877-1672

Toll Free (866) DO-FIBER

24/7 Technical support

(714) 366-2503

(714) 457-5740

Contact Information

Corporate Headquarters

RLH Industries, Inc.

936 N. Main Street

Orange, CA 92867 USA

Phone

Local (714) 532-1672

Toll Free (800) 877-1672

Toll Free (866) DO-FIBER

Fax

(714) 532-1885

info@ﬁberopticlink.com

Web site

www.ﬁberopticlink.com

RLH Industries, Inc.

936 N. Main Street, Orange, CA 92867 USA

T: (714) 532-1672

F: (714) 532-1885

Please contact your RLH sales representative

for pricing and delivery information.

Speciﬁcations subject to change without notice.

Page 6!!!RLH Industries, Inc. • Tel. 866-DO-FIBER • Fax 714 532-1885 • www.ﬁberopticlink.com

Speciﬁcations subject to change without notice.

Tabla de contenidos

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario