RKI Instruments PS-2 Manual de usuario
5/24/01
Installation and Operating Instructions
RKI Model PS-2 gas Monitor
This Monitor is calibrated as follows: Gas_____________________
Alarm 1 level______________
Alarm 2 level______________
Thank you for selecting our the RKI Model PS-2 gas monitor for your gas monitoring needs.
With proper installation and care, it will provide you with many years of trouble-free
operation.
Description:
The Model PS-2 is a multipurpose gas monitor utilizing a Metal Oxide sensor for long
life and low maintenance detection of many gases and solvents. The instrument is
powered by either 115 VAC or 24 VDC, (48 VDC version also available). It consists of
a plastic enclosure with flanges provided for wall mounting. Holes are provided on
the base of the housing for wiring entry, and the unit is supplied with the gas sensor
located on the end of a 30 foot cable. The PS-2 has two alarm levels, calibrated to the
gas and concentrations given above. Each alarm level activates a 10 amp relay inside
the unit, and terminals are provided for wiring the relay to activate an external
alarming device or activate some other device such as a ventilation fan. The front of
the unit contains three lights; Pilot, Alarm 1, and Alarm 2. An internal audible alarm is
also provided which activates for a gas alarm condition.
When you receive your PS-2, it will consist of 3 parts:
1. The main unit with sensor cable attached.
2. The lid, which will be placed on the unit but will not be screwed down.
3. A bag of parts which include the 2 mounting flanges, 10 screws for the
mounting flanges and the lid, 3 strain relief bushings for use during installation
for the wires entering the case, and 4 small plastic caps to press over the front
screwholes for cosmetics when the installation is completed.
RKI Instruments, Inc. • 33248 • Union City, CA 94587 • Tel: (510)441-5656 • Fax: (510)441-5650
World Leader in Gas Detection & Sensor Technology
www.rkiinstruments.com
Installation :
1. Remove the parts from the box and with the screws provided install the 2 mounting
flanges on the top and bottom rear of the instrument enclosure.
2. Using the mounting flanges, install the monitor on a wall within 30 feet of the area to
be monitored.
3. Using the 3 holes provided on the base of the unit, and the strain reliefs provided, run
wires for power and relay connections.
A. For 24 VDC Power, attach power wires to the terminals marked “DC IN,
+ and -”. For 115 VAC operation, the unit is supplied with a power cord to
plug into any 3 prong 115 VAC power outlet.
B. Relays are normally de-energized, so connecting to the “C” and “NO”
terminals will cause an electrical contact to be closed when the instrument
senses gas that exceeds the alarm levels.
Note : Wiring sizes for the relay connections must be adequately sized for the device
to be driven. Wiring size for the power wires can be 22 gage or greater.
4. Gas sensor is the blue bell shaped device located on the end of the 30 foot cable.
Locate the sensor in a face down direction near to where the gas would be expected to
accumulate. Sensor can be secured by clamping either the sensor or the sensor wire to
the wall. Do not drill holes through the sensor body. Sensor wires can be shortened if
desired, and if so please take note of sensor wire colors and be sure to match them to
the correct terminals after cutting.
5. Apply power to the PS-II to confirm proper connection and operation of all wires and
external devices. Please note that during power up, the PS-2 will usually go into alarm
condition for about 15 to 60 seconds. This is normal, and is a good time to confirm that
all external alarming devices are also functioning.
6. After proper operation is confirmed, secure the housing cover in place with the 4
screws provided, and place the small blue caps over the screw holes.
Maintenance :
The PS-2 requires no normal maintenance other than to confirm operation and
calibrate with a gas sample once every year or two, if possible. (Some gas mixtures
are not practical to make into compressed gas calibration cylinders. Please consult
factory to determine if your calibration can be made into cylinders. If cylinders are not
practical, the unit can be sent to RKI for factory calibration periodically.)
Calibration :
Please note that the PS-2 units are calibrated before shipment, so initial calibration is
not necessary unless the alarm levels need to be changed from the factory set levels. It
is recommended that the calibration be confirmed on the PS-2 at least once per year.
To do this, you will need the following equipment, which can be supplied by RKI
Instruments :
1. Calibration gas cylinders at each of the alarm points.
2. Cylinder valve or regulator (desired flow rate is 0.5 liter per minute).
3. Sample tube and test cup to apply gas to sensors.
4. Small screwdrivers: (Phillips head to remove case screws and small flat blade to
make calibration/alarm adjustments).
To Calibrate/Set Alarm levels, proceed as follows:
1. Remove front cover of the PS-2 by removing the 4 corner housing screws.
2. Connect the regulator, hose, and test cup to the Alarm 1 gas cylinder.
3. Secure the test cup to the sensor and let the gas flow onto sensor for approx. 60
seconds to allow time for full response.
4. While the gas continues to flow onto the sensor, with a fine flat blade
screwdriver adjust the LOW ALARM potentiometer adjustment (located on the
right hand side of the PCB just under the buzzer). Adjust the potentiometer as
follows:
A. If the buzzer is sounding and the yellow alarm light is lit, turn the
potentiometer clockwise slowly until the yellow alarm light just goes
out. Now, turn the potentiometer counter clockwise slowly until the
alarm light (and buzzer) just goes on. Low alarm is now set.
B. If the yellow light is not lit, turn the potentiometer slowly counter-
clockwise until the yellow light just goes on. Low alarm is now set.
5. A. Disconnect the gas regulator from theAlarm 1 gas cylinder and connect
it to the Alarm 2 gas cylinder. Allow approx. 60 seconds for full
response.
B. With the gas continuing to flow, adjust the HIGH ALARM
potentiometer as described in step 4A or 4B above, while watching for
the red light to come on. (note buzzer will sound during this entire stage
because the low alarm level is exceeded).
6. When finished, remove the regulator from the gas cylinder to stop the flow,
and replace the cover of the PS-2 housing.
Fuses : The PS-2 contains 2 fuses; a 1 amp fuse for the DC circuit, and a 250 ma (1/4
amp) fuse for the 115 VAC side.Both fusesare 4 mm x 20 mm type, and are
clearly labeled on the PCB with the housing lid removed. Turn off power when
replacing fuses.
For replacement parts, calibration equipment, repairs, or other information on this
equipment, please contact RKI Instruments, Inc, 33248 Central Ave., Union City, CA, 94587,
Phone (800) 754-5165, Fax (510) 441-5650 or contact us by visiting our web site at
www.rkiinstruments.com.
Tabla de contenidos
Otros manuales de Instrumento de medición de RKI Instruments
RKI Instruments
RKI Instruments GP-03 Manual de usuario
RKI Instruments
RKI Instruments OX-500 Guía de configuración
RKI Instruments
RKI Instruments GD-70D4 Series Manual de usuario
RKI Instruments
RKI Instruments 65-2322RKSS Manual de usuario
RKI Instruments
RKI Instruments GX-2001 Manual de usuario
RKI Instruments
RKI Instruments GD-K77D Manual de usuario
RKI Instruments
RKI Instruments GX-6000 Manual de usuario
RKI Instruments
RKI Instruments beacon 410 Manual de usuario
RKI Instruments
RKI Instruments GX-Force Manual de usuario
RKI Instruments
RKI Instruments GX-8000 Manual de usuario
RKI Instruments
RKI Instruments GX-2012 Manual de usuario
RKI Instruments
RKI Instruments 03 Series Manual de usuario
RKI Instruments
RKI Instruments GX-2003 Manual de usuario
RKI Instruments
RKI Instruments GP-03 Manual de usuario
RKI Instruments
RKI Instruments 01-Series Manual de usuario
RKI Instruments
RKI Instruments GX-3R Manual de usuario
RKI Instruments
RKI Instruments 72-RA-C Manual de usuario
RKI Instruments
RKI Instruments EAGLE 2 Manual de usuario
RKI Instruments
RKI Instruments CO-04C Manual de usuario
RKI Instruments
RKI Instruments CX-04 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario