Riva RC2102HD-5511 Manual de usuario
1
www.rivatech.de
Quick Installation Guide
This manual provides instructions for quick installation and basic configuration of your IP device.
2
www.rivatech.de
Step1. Connect cables to IP device
Connect required cables to the device including the power cable, LAN cable, and other
optional cables. To see the correct positions of all connectors, refer to the following image
below.
The device is polarity sensitive. Incorrect power
connection may cause malfunction or damage to
the IP device.
Caution
!
Power Adaptor Connector
(DC 12V)
* Model designs are subject to change without any prior notice.
LAN Cable
Connect
Reset Button
MicroSD Slot
Power Adaptor
Connect
PAL/NTSC button*
9 Pin Terminal Block
for video, audio, DI, and
DO
*This button is located under PCB.
*Pressing the button cycles
through PAL, NTSC, and no
video output mode:
No video
output -> PAL->NTSC
.Video
out is used only for installation
and works for 3 minutes when
PAL/NTSC button is pushed.
3
www.rivatech.de
Caution
!
Step2. Install IP device
Semi-flush mount
1) Place the installation template on a
surface where camera is going to be
installed and mark the anchor block
placements.
2) Drill and insert anchor blocks on a
marked surface.
3) Mount the main camera body by
aligning the anchor blocks and hold
against the mounting surface..
4) Tighten the anchor blocks with screws
5) Connect all the appropriate cables to
the device
6) Attach the dome cover on main body
and lock it up by rotating.
When placing the dome cover, look for carved triangle mark on both dome
cover and main body. Both triangles should be aligned together when
placing the cover. Once the cover has been placed, rotate the dome cover
for a secure lock. To detach the cover, rotate the dome cover and align
two triangle marks, and pull the cover.
When assembling the main body of the camera and its dome cover, make
sure they fit each other into place.
The camera may fall off the ceiling even after the proper installation and
mounting. To prevent any accident, make sure the ceiling is firm and stable
enough to support the camera. If any reinforcement is needed, consult
with your safety personnel and proceed with the installation.
Caution
!
4
www.rivatech.de
Caution
!
Flush mount
1) Trace the size on a surface where
the device will be inserted with the
provided template and create a hole.
Also, mark on a surface where
anchor blocks will be inserted.
2) Drill and insert anchor blocks on a
marked surface.
3) Connect all the appropriate cables
to the main device and place on the
center of the hole. Cables should be
wired from other side of the exposed
surface.
4) Unscrew 3 bolts that are on the dome
cover’s surface and place the FMB
mount in between the top dome shelf
and bottom circular cylinder. Align to the
screws holes and re-tight 3 components
with bolts.
5) Attach the dome cover on main body
from the surface side where it will be
exposed and lock it up by rotating the
cover.
6) Tighten the mounted surface’s anchor
blocks with screws on a FMB mount
parts.
When placing the dome cover, look for carved triangle mark on both dome
cover and main body. Both triangles should be aligned together when
placing the cover. Once the cover has been placed, rotate the dome cover
for a secure lock. To detach the cover, rotate the dome cover and align
two triangle marks, and pull the cover.
When assembling the main body of the camera and its dome cover, make
sure they fit each other into place.
The camera may fall off the ceiling even after the proper installation and
mounting. To prevent any accident, make sure the ceiling is firm and stable
enough to support the camera. If any reinforcement is needed, consult
with your safety personnel and proceed with the installation.
Caution
!
5
www.rivatech.de
Step3. Set the lens position
IPN2102HD’s lens is prepositioned, therefore cannot be modified.
Step4. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of
the device from converting the MAC address’s hexadecimal numbers, which is attached to the
device. Be sure that the device and PC are on a same area network before running the
installation.
Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX are
used, users may view the live streaming images on a web page using the device’s default IP
address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal
Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the IP address of the device.
3. Web streaming and device configurations are supported through ActiveX program. When
the ActiveX installation pop-up window appears, authorize and install the ActiveX setup.exe.
MAC address = 00-13-23-01-14-B1 →IP address = 192.168.20.177
Convert the last two set of hexadecimal numbers to decimal numbers.
6
www.rivatech.de
Custom IP Environment
IPAdminTool and the manual are provided on USB stick or can download from www.rivatech.de
homepage.
IPAdminTool is a management tool, which automatically scans all of the network products for
users to perform administrative tasks, which includes network configurations, firmware update,
device reboot, and device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select “IP Address”; IP Setup window appears.
7
www.rivatech.de
3. In the IP Setup’s window, information under ‘Local Network information’ displays the
user/PC’s network area information. Those information need to be incorporated to the
IP Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP
Address, which are to be the unique numbers for the device. Refer to the image above
for the setting
4. Click ‘Setup’ to complete the modification. When the dialog box appears to request user
name and password, enter the default value for the administrator account (case-
sensitive) as below:
ID:
root
Password:
pass
PC environment Info
Give new unique IP address in
last two sets and mirror other
information in other boxes
8
www.rivatech.de
Step5. View video on web page
Once the device has the proper IP address, users can view the live streaming images
through a web browser.
The default username and password is
root / pass
.
1. When the device’s web address is accessed, the browser asks to install the ActiveX.
Click Allow.
2. Setup.exe installation link or pop-up window appears, depends on Microsoft® Internet
Explorer version. Proceed with rest of setup installation.
9
www.rivatech.de
Caution
!
3. Follow the instructions of the dialog boxes and complete the installation. Once the
installation is complete, start the web browser again and check if video stream is
displayed in the main view frame.
If “
This software requires the Microsoft XML Parser V6 or higher.
Please download MSXML6 from the Microsoft website to continue.
Error code: Cannot create XMLDOMDocument.
” message appears,
download and install the Microsoft Core XML Services (MSXML)
10
www.rivatech.de
Rebooting
Perform the following procedures to reset your device:
1. While the device is on, press the reset button for 1~2 seconds.
2. Wait for the system to reboot.
Resetting to the Factory Default Settings
When reset the device to the factory default setting, all parameters including the IP address
will be initialized.
To proceed back to the Factory Default reset:
1. While the device is on, press reset button and hold.
2. Release the Reset button after about 5 seconds when green LED blinks at rate of 200ms.
3. Wait for the system to reboot.
More Information
To learn more about using other features of your devices, refer to the manuals as “Web
Interface Manual” or “VCAsys _Online_Help”, which is available on USB stick or on
www.rivatech.de homepage.
Otros manuales para RC2102HD-5511
1
Tabla de contenidos
Otros manuales de Cámara IP de Riva
Riva
Riva RC2102HD-5511 Manual de usuario
Riva
Riva RTC series Manual de usuario
Riva
Riva RC2103HD-6611 Manual de usuario
Riva
Riva RC6702HD-6311 Manual de usuario
Riva
Riva RC1202HD-5241 Manual de usuario
Riva
Riva RTC1130 Manual de usuario
Riva
Riva RC1202HD Manual de usuario
Riva
Riva RC1100M Manual de usuario
Riva
Riva RC6802HD-6211 Manual de usuario
Riva
Riva RC2103HD-6611 Manual de usuario
