Ritetemp 6004 Manual de usuario

.ON

.OFF

ENGLISH

Install Guide 6004

Location

Caution

Tools

To avoid electrical shock and to prevent damage to the heating system,

and thermostat, disconnect the power supply before beginning work.

This can be done at the circuit breaker, or at the appliance.

C A U T I O N

Your thermostat is a precise instrument. Please

handle it with care.

Turn off electricity to the appliance before installing or

servicing thermostat or any part of the system. Do not

turn electricity back on until work is completed.

Do not short (jumper) across electric terminals at

furnace control to test the system. This will damage

the thermostat and void your warranty.

All wiring must conform to local codes and ordinances

Wiring must come through, and the thermostat

mounted on a standard approved electrical junction

box.

This thermostat is designed for use with 120-220 volt

AC systems. The thermostat should be limited to a

maximum of 16.0 amps; higher amperage may cause

damage to the thermostat.

.On replacement installations, mount the new thermostat in

place of the old one.

.On new Installations, follow the guidelines listed below.

Locate the thermostat on an inside wall, about 5 ft. (1.5m)

above the floor, and in the room where the heater is situated.

.Do not install where there are unusual heating conditions, such

as: in direct sunlight; near a lamp, radio, television, or above

the baseboard heater, or fireplace; near hot water pipes in a

wall; or any other heat source.

.Do not locate in unusual cooling conditions: in a draft from a

stairwell, door, or window; or on the wall of an unheated room.

.Do not locate in a damp area. This can lead to corrosion that

will shorten thermostat life.

.Do not locate where air circulation is poor, such as: in a corner

or an alcove; or behind an open door.

.Do not install until completion of construction and painting.

.This thermostat does not require leveling.

You will need #1 Phillips screwdriver (small)

PG 1

PG 2

Good

5ft.

(1.5m)

Install Guide 6004

Remove old unit

Connect wires

.Switch electricity to the heater OFF at the circuit breaker;

then proceed with the following steps.

.Remove cover from old thermostat. Most are snap-on types and

simply pull off. Some have locking screws on the side or front.

These must be loosened to remove cover.

.Remove the old unit from the terminal box, by unscrewing the

captive screws.

.On your new thermostat, separate

Control Unit (front) from Wall Unit (back).

.Grasp the front of the unit and the back of

the unit and gently pull the thermostat body

away from the base.

Caution

Make sure you note which wire is which when

you disconnect the old thermostat. Use only

UBC approved wire nuts to connect wires.

If you have 4 wires (Double Pole), inside the wall box,

follow these wiring instructions.

.Connect the LOAD to the RED wires (T1, T2)

and the LINE to the BLACK wires (L1, L2).

.Twist wires together first, then secure by twisting

wire nut on.

.Push the wires and

wire nuts

into the

terminal

box.

LOAD

LINE

Junction box in wall

RED

BLACK

RED

TO LOAD

TO LINE

BLACK

STAT

CAUTION HIGH VOLTAGE!

DISCONNECT POWER SUPPLY

BEFORE SERVICING

Connect wires cont.

If you have 2 wires (Single Pole) inside the wall box,

follow these wiring instructions.

.Connect the LOAD to the RED wire (T1)

and the LINE to the BLACK wire (L1).

.Connect BLACK-L2 and RED-T2 from the back of

the thermostat together.

.Twist wires together

first, then

secure by

twisting

wire nut on.

.Push the

wires and

wire nuts

into the

terminal box.

PG 6

Attach Unit

.Position (optional) wall plate over

junction box.

.Align the 6-32 captive screws with

the threaded holes in the junction box.

.Screw the wall unit to the junction

box.

Note: Do not reattach

control unit until batteries

have been inserted.

RED

TO LOAD TO LINE

BLACK

STAT

CAUTION HIGH VOLTAGE!

DISCONNECT POWER SUPPLY

BEFORE SERVICING

OFF

TO LOAD

TO LINE

Junction box in wall

RED

BLACK

RED

TO LOAD

TO LINE

BLACK

STAT

CAUTION HIGH VOLTAGE!

DISCONNECT POWER SUPPLY

BEFORE SERVICING

PG 8

Replace front of control unit on the

wall unit.

Check Unit

Follow these procedures to verify

you have correctly installed the

unit.

To check HEAT mode:

Set the AC POWER switch to ON.

Turn TEMP DIAL counter clockwise to its

highest stop. This is the warmest setting. Allow the

system 5 min to respond. Verify that heat is

coming from the system.

Return dial to comfortable setting.

O N

OFF

Install Batteries

.The 6004 requires 2AA batteries.

.On the control unit, Switch AC POWER

switch to OFF.

.Install 2 AA alkaline batteries according

to the polarity noted in the compartment.

DO NOT USE Rechargeable Batteries.

Caution: The thermostat will go "off" if the

batteries die. This exposes your house to

unexpected heat or cold and should be

avoided.

NOTE: Replace the batteries when the red

LOW battery LED indicator blinks or once a

year.

Install Batteries cont

6004 Features

Notes

The 6004 can be used with

most 120/208/240 volt

electric heating devices. It

provides Line voltage control

for radiant cable, electric

baseboard, and wall heaters

within the ratings listed.

Electrical Rating -

120/208/240 Vac;

16A max load

OFF

1611-004

.ON

.OFF

Customer Support: 877-505-2353

or Visit our website www.ritetemp-thermostats.com

Printed in China

Tabla de contenidos

Otros manuales de Termostato de ritetemp

ritetemp

ritetemp 6025 Manual de usuario

ritetemp

ritetemp 6004 Manual de usuario

ritetemp

ritetemp 8030C Manual de usuario

ritetemp

ritetemp 6020 Manual de usuario

ritetemp

ritetemp 8022 Manual de instrucciones

ritetemp

ritetemp 8025 Manual de usuario

ritetemp

ritetemp 6022 Manual de usuario

ritetemp

ritetemp 8046 Manual de usuario

ritetemp

ritetemp 8010 Manual de usuario

ritetemp

ritetemp 6008 Manual de usuario

ritetemp

ritetemp 6022 Manual de usuario

ritetemp

ritetemp 6010 Manual de usuario

ritetemp

ritetemp 6036 Manual de usuario

ritetemp

ritetemp 8082C Manual de usuario

ritetemp

ritetemp 8030 Manual de usuario

ritetemp

ritetemp 8050C Manual de usuario

ritetemp

ritetemp 6030 Manual de usuario

ritetemp

ritetemp 8025 Manual de usuario

ritetemp

ritetemp 8082 Manual de usuario

ritetemp

ritetemp 8030C Manual de usuario

ritetemp

ritetemp 8022C Manual de instrucciones

ritetemp

ritetemp 8085 Manual de usuario

ritetemp

ritetemp 8010 Manual de usuario

ritetemp

ritetemp 8085c Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario