7
DMX Address
Writing Function
(to support the
address writing for
single lamp)
(to support the
address writing for
multiple lamps)
(to support the same
of the first address
of each lamp)
2
:
:
:
WRITING ADDR 001
REP 01 STEP 48
Press SPEED +/- to switch 3 parameters, press BRT +/- to
change the value.
WRITING ADDR: Write the first address of the DMX lighting,
the default is 001.
REP: Write the actual pixels, the default is 01, means the
lamps assigned to 16 pixels.
STEP: Fill in the plus & minus step when set the "WRITING
ADDR", the default is 48, meaning each plus & minus
step is 48 for the first address.
1. When writing address for each lamp individually, use the
"step" can quickly modify the first address of each lamp.
2. When multiple lamps in series connection and set the "REP"
as 01,02,04,08,16, each lamp is assigned 16,8,4,2,1 pixels
individually, the first address of each lamp will increase
progressively. For instance, set the "WRITING ADDR" as
001," REP as 02, then the first address of each lamp is 001,
025,049 in sequence, each lamp is assigned 8 pixels.
3. When multiple lamps in series connection and set the
"REP" as 01S,02S,04S,08S,16S, each lamp is assigned 16,8,
4,2,1 pixels individually, set the same first address for all lamps.
For instance, set the "WRITING ADDR" as 001, "REP" as 02,
then the first address of all lamps together is 001, each lamp
is assigned 8 pixels.
Submenu Function
(Press MODE+/- to
Change Menu Below) LCD Display Setting Methods
No.
The DMX address
testing verification
3
:
:
:
TESTING ADDR 001
VAL 255 STEP 48
TESTING ADDR: fill in the test address value.
VAL: fill in DMX value from 0 to 255 in the testing address,
default is 255. for the other DMX address, the date sent is 0.
STEP: fill in the plus & minus step when set the "WRITING
ADDR", the default is 48, meaning each plus & minus step is
48 for the testing address.
8. Attention:
8.1 The product shall be installed and serviced by the qualified person.
8.7 If a fault occurs please return the product to your supplier. Do not attempt to fix this product by
yourself.
8.6 Ensure all wire connections and polarities are correct before applying power to avoid any damages
to the LED lights.
8.5 Please ensure that adequate sized cable is used from the controller to the LED lights to carry the
current. Please also ensure that the cable is secured tightly in the connector.
8.4 Please check if the output voltage of the LED power supply used comply with the working voltage
of the product.
8.3 Good heat dissipation will prolong the working life of the controller. Please ensure good ventilation.
8.2 This product is non-waterproof. Please avoid the sun and rain. When installed outdoors please
ensure it is mounted in a water proof enclosure.
8
9. Warranty Agreement:
9.1 We provide lifelong technical assistance with this product:
★This manual only applies to this model. We reserve the right to make changes without prior notice.
9.4 Any amendment or adjustment to this warranty must be approved in writing by our company only.
9.3 Repair or replacement as provided under this warranty is the exclusive remedy to the customer. We
shall not be liable for any incidental or consequential damages for breach of any stipulation in this
warranty.
9.2 Warranty exclusions below:
For faults beyond the 5-year warranty, we reserve the right to charge for time and parts.
A 5-year warranty is given from the date of purchase. The warranty is for free repair or replacement
if cover manufacturing faults only.
Any man-made damages caused from improper operation, or connecting to excess voltage and
overloading.
The product appears to have excessive physical damage.
Damage due to natural disasters and force majeure.
Warranty label, fragile label and unique barcode label have been damaged.
The product has been replaced by a brand new product.
