Rinnai N-BW2 Manual de usuario
PWR BUS WIFI SER
ZONES
FAN
MODE
M
SCHEDULE
MANUAL HEAT
Temporary
Set to
20o
Current Temperature
20o
10:21 pm
MENU
95%
11 :25 pm Thursday
ON / OFF
Rinnai Touch Wi-Fi Kit
N-BW2 Installation Manual
APPLY MODULE
IDENTIFICATION LABEL
HOME OWNER TO RETAIN FOR FUTURE REFERENCE
Rinnai 3 Touch Wi-Fi Kit IM
Congratulations on the purchase of a Rinnai Touch Wi-Fi Kit
that is compatible with Rinnai and Brivis home comfort systems,
specically Ducted Gas Heating, Dual Comfort (Add-On
Refrigerated Cooling) or Evaporative Cooling systems with
Wired Networker Controller.
Important Note
Read this manual carefully before installing or operating your
Wi-Fi Module. Make sure to save this manual for future reference.
For reliable connection to the Wi-Fi module, router rmware and
smart device software should be the latest version.
Terms and Conditions
The Terms and Conditions are available when downloading the
Rinnai Touch App used to connect with the Wi-Fi Module. Please
read these carefully before proceeding.
Disclaimer
IMPORTANT NOTICE: This document is a guide only. Laws,
regulations and industry standards can vary between States and
Territories. Accordingly, this guide must be read in conjunction
with, and subject to, all laws, regulations and industry standards
applicable in the State or Territory in which the products are
installed. You must ensure that the installation of the products will
comply with those laws, regulations and standards, and that the
products recommended to customers are t for the purpose for
which they are intended.
Privacy Notication
Rinnai Australia Pty Ltd will collect personal information when
warranty and maintenance registration forms are completed.
This personal information is collected under the guidance of the
Privacy Information Protection Act 1998.
The purpose of collecting this information is to:
• process customer requests for us to provide service activities;
• register purchases of equipment for warranty;
• register requests for a survey/quotation for heating, ventilation,
and air conditioning goods and services.
The intended recipients of the information are:
• employees of Rinnai.
• federal and state governments who may require the information
for administration purposes.
While the supply of the information is voluntary, if our customers
cannot, or do not wish to provide the information sought, the
company may not be able to provide the services requested. If
information has already been provided, an application can be
made for access or amendment of that information, or to request
that it not be used. Customers have a right of access to, and
correction of, the information concerning them in accordance with
the relevant procedures under the Act.
Enquiries concerning this matter can be addressed to the
Business Practices Ocer using the “Contacts” on page 20.
With our policy of continuous improvement, we reserve the right to change, or
discontinue at any time, specications or designs without notice.
Pictures for illustration purposes only.
All rights reserved. No part of these documents may be used in any way or form
without prior written consent from Rinnai Australia Pty Ltd.
™ iOS is a trademark of Apple Inc.
™ Android is a trademark of Google LLC.
Rinnai 4 Touch Wi-Fi Kit IM
Table 1. Denitions
Abbreviation Description
N-BW2 N-BW2 Networker Bridge (Wi-Fi Module)
SSID Service Set Identier
WPA Wi-Fi Protected Access
TCP Transmission Control Protocol
AP Access Point
MTSP Multi-Temperature Set Point
STSP Single Temperature Set Point
N-PM1 Zone Plus Power Module
NC-3 Networker Controller (pre 2010)
NC-6 Networker Controller (from 2012)
NC-7 Networker Touch Controller
NT-1 Networker Remote Temperature Sensor
Shall
Indicates a mandatory requirement of this manual.
Should
Indicates a recommended requirement of this manual.
Any deviations from these instructions may, at the discretion of the
manufacturer, void the warranty. As a result, the customer and/or
installer may be charged a fee for non-product warranty related
call outs. Also note that failure to comply with these instructions
may preclude company service personnel from being able to
service the device.
GLOSSARY
Default Access Point (AP) state.
All N-BW2 Wi-Fi Modules are defaulted to this state when rst
powered on. When in this state only the Wi-Fi conguration mode
is allowed. The default Access Point is the software state of the
Module out of the box. Pressing and holding the AP button while
the module is switched on will force the Wi-Fi Module to operate
at these factory settings.
Home Direct
In this state the N-BW2 Wi-Fi Module operates as an access point
which can be associated with the SSID and WPA passphrase
dened by the user. When operating in this state a network
router is not needed to access the Networker system. By default
the N-BW2 Wi-Fi Module will operate in the Networker system
access mode. Once congured, re-conguration of the N-BW2
Wi-Fi Module can only be performed by placing the module into
its Default Access Point (AP) state.
Router Mode
In this state the N-BW2 Wi-Fi Module associates with a router, the
SSID and WPA passphrase congured to match that of the router.
This is the most common state the Wi-Fi Module operates in. By
default the Wi-Fi Module will operate in the Networker system
access mode but can revert to the Wi-Fi conguration mode.
Once congured, re-conguration of the N-BW2 Wi-Fi Module
can only be performed by placing the module into its Default
Access Point (AP) state.
Rinnai 5 Touch Wi-Fi Kit IM
WARNINGS AND IMPORTANT INFORMATION
IMPORTANT
READ ALL INSTRUCTIONS BEFORE USING.
Always comply with the following precautions to avoid dangerous situations and to ensure optimum performance.
Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property
damage, personal injury and/or death.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in personal injury or death.
WARNINGS: Indicates a potentially hazardous situation which, if not avoided, could result in personal injury or
death.
CAUTIONS: Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate
injury or damage to the appliance. It may also be used to alert against unsafe practices.
WARNING
WARNING.
The Rinnai Touch Wi-Fi Module is supplied with a 12V DC Plug Pack Socket if required. Only this power supply must
be used.
The Module must be installed indoors only. Installation must be performed by a qualied person and in accordance
with local and national wiring laws.
The Module is NOT intended for use by persons (including children) with reduced physical, sensory or mental
capacities, or lack of experience and knowledge unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If any cables are damaged, they shall be replaced by the manufacturer or its service agent or similarly qualied
person in order to avoid a hazard.
Stranded conductors shall not be consolidated by lead-tin soldering where they are subject to contact pressure.
Rinnai 6 Touch Wi-Fi Kit IM
1.0 TABLE OF CONTENTS
1.0 Hardware Installation 7
1.1 Kit Contents .................................................................7
1.2 Compatibility and Requirements ..................................7
1.3 Specications ...............................................................7
2.0 Module Overview 8
3.0 Pre-Installation 10
4.0 Installation 10
4.1 Wi-Fi Module Location ..............................................10
4.2 Securing the Wi-Fi Module ........................................ 11
4.3 Electrical Control Wiring ............................................ 11
5.0 Wi-Fi Module Unique Identication Labels 15
6.0 Powering On 16
7.0 Wi-Fi Module Error Codes 17
8.0 Warranty 19
Contacts 20
Rinnai 7 Touch Wi-Fi Kit IM
1.0 HARDWARE INSTALLATION
1.1 KIT CONTENTS
• N-BW2 Wi-Fi Module
• 12V DC Power Pack
• 20m Interconnecting Cable (for use with NC-7 only)
• Screws, Plugs and Mini Screwdriver
• Unique Module Identication Labels
• This installation manual (must be retained by the home owner).
1.2 COMPATIBILITY AND REQUIREMENTS
Product Compatibility
Home Comfort Systems: Rinnai/Brivis Ducted Gas Heating, Dual
Comfort (Add-On) or Evaporative Cooling system.
Existing Wired Networker Controller
Rinnai/Brivis Networker Controller: NC-3, NC-6 or NC-7 Touch.
Home System Requirements
Working Wireless Wi-Fi connection: 802.11b/g/n @2.4GHz
(Security: WPA2) where applicable.
Mobile Device
iOS 8 and Android 4.0.3 (API 15) or higher
1.3 SPECIFICATIONS
• Standard: IEEE 802.11b/g/n
• Antenna Type: Internal
• Frequency: Wi-Fi 2.4GHz
• Minimum & Maximum Operating Temperature Range: 0°C to
70°C
• Operating Relative Humidity: 10%–85%
• Power Input: DC 12V/300mA
• Location: Wi-Fi Module shall be within 10m of wireless router
where applicable.
Rinnai 8 Touch Wi-Fi Kit IM
2.0 MODULE OVERVIEW
Figure 1. Operating Indicator (front view)
PWR BUS WIFI SER
1 2 3 4
Figure 2. Operating Features (back view)
PWR AP LNK
5
678
10
9
TW1
TW2
TW1
TW2
Rinnai 9 Touch Wi-Fi Kit IM
Table 2. Operating Indicators
FRONT VIEW
1 PWR Power on/Primary module operation indication
2BUS Networker system communication indication
3 Wi-Fi Wi-Fi module operation indication
4SER Not used
REAR VIEW
5USB Not used
6Plug Pack Socket
12V DC
Supplied in the kit is a power adaptor which steps down the supplied voltage from 240VAC to 12V DC.
The 12V DC terminal end inserts into the ‘Plug Pack Socket’ on the Wi-Fi Module. In NC-7 based systems if
three or less NC-7 Touch controllers are installed the power adaptor is not required.
7 PWR The Power ON/OFF button isolates power to the device, disabling system control through the App. The DC
power supplied from the TW1 & TW2 terminals on the Wi-Fi module is not impacted from this power isolation.
8 AP This button allows the Wi-Fi Module to be forced to its Default AP State. To do this follow the procedure as
outlined below.
1. Switch Power OFF to the Wi-Fi Module
2. Press the AP button.
3. While pressing the AP button, switch power ON to the Wi-Fi Module.
4. Keep pressing the AP button until the Wi-Fi LED ashes orange.
9Networker NC-7
Touch Connection
When three or less NC-7 Touch controllers are installed the loom supplied with the Wi-Fi kit provides both the
power and communication connections. One end of the 20m loom connects to the ‘Touch Connection’ socket
on the Wi-Fi Module and the other to a spare socket on the NC-7 Interface Module in Figure 4 on Page 12.
10 2-Wire Bus
Connections
The 2-wire bus connection terminal block facilitates 2-wire bus connection of heating/cooling appliances,
NC-3/NC-6 Networker controls and NT-1 Sensors.
Rinnai 10 Touch Wi-Fi Kit IM
3.0 PRE-INSTALLATION
The following sequence of tasks will assist with conguration and
installation of your Wi-Fi module.
1. Position the Wi-Fi Module and install in accordance with
Section 4.
2. Ax the loose supplied Unique Identication Label onto
the backing plate of the Master Networker Controller. See
Section 5.
3. Turn power onto your system.
4. Download the latest Rinnai Touch Owner’s Manual from
www.rinnai.com.au.
5. Download the Rinnai Touch App from the Apple Store or
Google Play.
6. Launch the App and follow the prompts to install.
4.0 INSTALLATION
4.1 WI-FI MODULE LOCATION
The Wi-Fi Module shall be positioned in a waterproof environment
within 10m of your wireless router (where applicable) to ensure
reliable communication. If this distance is more than 10m the
transmitting signal may be predisposed to interruption. Please
consult your installer in the rst instance if this issue is identied.
The environment must not exceed a temperature of 70°C and
relative humidity of 85%.
IMPORTANT
The Wi-Fi Module MUST NOT be installed
inside any appliance cabinet as this will
adversely aect the Wi-Fi connection.
Otros manuales para N-BW2
1
Tabla de contenidos
Otros manuales de Unidad de control de Rinnai
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
