RIGTEC AF02-X40 Manual de usuario
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
AIR FRAME X-40
(AF02-X40)
USER GUIDE
Version 1.0
Revision Date Revision Details Revised By
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
Thank you for purchasing a Rigtec Air Frame.
We hope you enjoy using the Air Frame as much as we’ve
enjoyed designing and manufacturing it.
If you have any questions, suggestions or just want to say hello;
please contact the team at [email protected]
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
CONTENTS
SAFETY INFORMATION 3
SAFETY INSPECTION 5
AIR FRAME PARTS 6
COMPATIBLE PROJECTORS 7
INSTALLATION ACCESSORIES 8
INSTALLING A PROJECTOR 9
ADJUSTMENTS 10
STACKING 11
STACKING LIMITS 12
REMOVABLE FRONT BAR 13
HANGING ACCESSORIES 14
ATTACHING AN ATOM GRIP:
LANDSCAPE 15
PORTRAIT 16
FLOOR PROJECTION 17
SWIVEL COUPLER SAFETY INFORMATION 18
ATTACHING SWIVEL COUPLERS:
LANDSCAPE 19
PORTRAIT 20
FLOOR PROJECTION 21
SAFETY STEEL CABLES 22
SPECIFICATION 23
DIMENSIONS 24
CE DECLARATION OF CONFORMITY 25
UKCA DECLARATION OF CONFORMITY 26
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
3
SAFETY INFORMATION
These instructions should be handed over to the
person carrying out the installation.
• Only a qualied, trained and competent technician should carry out
installation work.
• The device should only be used with approved accessories and spares.
• Do not exceed the Working Load Limit (WWL) – when used with other
accessories make sure that the Working Load Limit of any component is
not exceeded.
• Care should be taken when lifting and moving – the combined weight of
the device and any accessory should be within safe manual handling limits.
• Care should be taken when transporting that injury is not caused - make
sure the device and any attached accessory is correctly secured.
• All equipment should be visually inspected before use and in the event of
any damage, it must be immediately taken out of service and assessed by a
competent person.
• Any suspended accessory must be independently secured with an
approved safety wire/s. Local laws or regulations should be consulted
regarding the additional safety of hanging equipment
• When working at elevated heights or under a suspended load, make sure
that all necessary precautions have been taken.
• Only install the approved projectors into the Air Frame, as listed in the User
Guide. Attempting to install projectors other than those listed in the User
Guide may result in serious injury.
• Do not use the Air Frame outdoors. The Air Frame should not be installed
where it can be exposed to wind or rain.
• Do not expose the Air Frame to moisture or excessive heat.
• Do not install the Air Frame on unstable surfaces.
• Do not hang the Air Frame from unstable, unsafe or inappropriate objects/
structures. Ensure the structure can support the overall weight.
• When stacking Air Frames, ENSURE all four locking pins are securely
positioned through the adjoining male and female Air Frame stacking
connectors.
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
4
SAFETY INFORMATION
These instructions should be handed over to the
person carrying out the installation.
• Do not install an Air Frame whilst people are under the hanging area.
• Do not make adjustments to a hanging Air Frame or Atom Grip whilst
people are under the hanging area.
• A Minimum of TWO people should be used to lift, carry and install the Air
Frame with a projector installed.
• Thorough examination of lifting equipment must take place at least every
12 months by a qualied technician.
In addition to these scheduled examinations, equipment will require a thorough
examination following:
• Any accident or dangerous occurrence.
• Any signicant change in conditions of use.
• Any long periods of inaction.
• Each time the equipment is used.
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
5
SAFETY INSPECTION
The Air Frame should always be inspected to check for defects and
loose bolts or nuts prior to installation or use.
It is important to inspect the Air Frame for damaged, broken,
misshapen or missing parts. If any of these issues are found, the
product must not be used.
Along with an overall visual check covering the issues above, the
following specic parts should be checked before the product is
used:
1. Ensure the nuts and bolts that connect the projector plate to
the rest of the frame are not loose.
2. All Atom Grip Attachment Plates must be inspected, it is
important to ensure that all threads are intact. If there is any
damage to the threads that Atom Grip Attachment Plate must
not be used.
1
2
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
6
PART NAMES
Use this page as a reference of the various part names throughout
this User Guide.
1. Ratchet Handle
2. Yaw Adjustment Handle
3. Projector Plate
4. Male Stacking Connector
5. Female Stacking Connector
6. Locking Pin
7. Landscape Atom Grip Attachment Plate
8. Portrait Atom Grip Attachment Plate
9. Floor Projection Atom Grip Attachment Plate
10. M8 Atom Grip Threads
11. Upper Side Bar
12. Lower Side Bar
13. Upper Back Bar
14. Lower Back Bar
15. Removable Front Bar
16. Removable Front Bar Bolts
17. Lower Front Bar
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
7
COMPATIBLE
PROJECTORS
The Air Frame projector plate has ve hole sets. One hole from
each set is labelled with a shape to aid the installation process.
When installing a projector, begin with the labelled hole which will
then line up the other holes in the associated hole set. Please see
the compatibility table for a full list of compatible projectors and an
itemisation of each hole set.
Hole Set 1
Square
Hole Set 2
Triangle
• Epson EB-L12000Q
• Epson EB-L20000U
• Barco G100 W16
• Barco G100 W19
• Barco G100 W22
• Optoma ZU1700
• Optoma ZU1900
• Optoma ZU2200
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
8
INSTALLATION
ACCESSORIES
Rigtec Air Frames are provided with all the necessary
accessories to install the projector into the Air Frame.
Bolts, washers and spacers will be required for all
projectors, using the incorrect size could lead to damage to
the projector or serious failure of the Air Frame. Please
consult this table to nd the correct bolts, washers and
spacers to use with your projector.
The number in brackets following the projector model
shows the quantity of bolts, spacers and washers required
for that model, this quantity must be used. Failure to use
the full amount of spacers, bolts and washers could lead to
serious failure of the Air Frame.
The full amount of spacers, bolts & washers MUST be used.
Please Torque bolts to 4±0.5 Nm (Or as recommended by
the Projector Manufacturer in the Projector User guide)
Only use supplied bolts to connect Air Frame and
Projector.
Projector
Model
M6
40mm Bolt
M6
10mm Spacer
M6
Washer
M8
30mm Bolt
M8
35mm Bolt
M8
10mm Spacer
M8
20mm Spacer
M8
Washer
Epson EB-L12000Q [6] ◆◆◆
Epson EB-L20000U [6] ◆◆◆
Barco G100 W16 [4] ◆◆◆
Barco G100 W19 [4] ◆◆◆
Barco G100 W22 [4] ◆◆◆
Optoma ZU1700 [4]
Use 8 Washers (2 per bolt)
◆◆◆
Optoma ZU1900 [4]
Use 8 Washers (2 per bolt)
◆◆◆
Optoma ZU2200 [4]
Use 8 Washers (2 per bolt)
◆◆◆
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
9
INSTALLING
A PROJECTOR
Required Tools:
• 10mm Spanner (for M6 Bolts)
• 13mm Spanner (for M8 Bolts)
See ‘Installation Accessories’ (page 8) for Bolt, Washer & Spacer
quantities & sizes.
1. Turn the projector upside down and place onto a stable at surface.
To make the installation as easy as possible it’s recommended to
place the projector onto an object to raise the projector body around
100mm from the chosen surface. Also raising the Air Frame
projector plate as high as possible by adjusting the ratchet handles
can simplify the installation.
2. Place the provided spacers over the mounting points (threaded
holes) of the projector, the chamfered side of the spacer should be
facing up away from the projector body.
3. Carefully lower the Air Frame over the projector, ensuring the ratchet
handles are at the front of the projector. Carefully line the projector
threaded holes up with the associated holes in the Air Frame plate.
4. Using the provided Bolts, secure the recommended number of bolts
(Please Consult the Projector Manufacturer’s User Guide) through
the provided Washers, then through the Air Frame plate holes, then
through the provided Spacers and into the projector’s threaded
holes. Use a spanner to tighten the bolts.
Please Torque bolts to 4±0.5 Nm (Or as recommended by the Projector
Manufacturer in the Projector User guide)
Only use supplied bolts to connect Air Frame and Projector.
12
43
Tabla de contenidos
Otros manuales de Rack y soporte de RIGTEC
