Rigol DS2000 Series Manual de usuario

RIGOL

Quick Guide

DS2000 Series Digital Oscilloscope

Mar. 2012

RIGOL Technologies, Inc

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

Guaranty and Declaration

Trademark Information

RIGOL is a registered trademark of RIGOL Technologies, Inc.

Publication Number

QGA13101-1110

Notices

RIGOL products are protected by patent law in and outside of P.R.C.

RIGOL reserves the right to modify or change parts of or all the specifications

and pricing policies at company’s sole decision.

Information in this publication replaces all previously corresponding materials.

RIGOL shall not be liable for losses caused by either incidental or consequential

in connection with the furnishing, use or performance of this manual as well as

any information contained.

Any part of this document is forbidden to be copied or photocopied or

rearranged without prior written approval of RIGOL.

Product Certification

RIGOL guarantees this product conforms to the national and industrial standards in

China. International standard conformance certification is in progress.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

Safety Requirement

General Safety Summary

Please review the following safety precautions carefully before putting the

instrument into operation so as to avoid any personal injuries or damages to the

instrument and any product connected to it. To prevent potential hazards, please use

the instrument only specified by this manual.

Use Proper Power Cord.

Only the power cord designed for the instrument and authorized by local country

could be used.

Ground The Instrument.

The instrument is grounded through the Protective Earth lead of the power cord. To

avoid electric shock, it is essential to connect the earth terminal of power cord to the

Protective Earth terminal before any inputs or outputs.

Connect the Probe Correctly.

Do not connect the ground lead to high voltage since it has the isobaric electric

potential as ground.

Observe All Terminal Ratings.

To avoid fire or shock hazard, observe all ratings and markers on the instrument and

check your manual for more information about ratings before connecting.

Use Proper Overvoltage Protection.

Make sure that no overvoltage (such as that caused by a thunderstorm) can reach

the product, or else the operator might expose to danger of electrical shock.

Do Not Operate Without Covers.

Do not operate the instrument with covers or panels removed.

Use Proper Fuse.

Please use the specified fuses.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

III

Avoid Circuit or Wire Exposure.

Do not touch exposed junctions and components when the unit is powered.

Do Not Operate With Suspected Failures.

If you suspect damage occurs to the instrument, have it inspected by qualified

service personnel before further operations. Any maintenance, adjustment or

replacement especially to circuits or accessories must be performed by RIGOL

authorized personnel.

Keep Well Ventilation.

Inadequate ventilation may cause increasing of temperature or damages to the

device. So please keep well ventilated and inspect the intake and fan regularly.

Do Not Operate in Wet Conditions.

In order to avoid short circuiting to the interior of the device or electric shock, please

do not operate in a humid environment.

Do Not Operate in an Explosive Atmosphere.

In order to avoid damages to the device or personal injuries, it is important to

operate the device away from an explosive atmosphere.

Keep Product Surfaces Clean and Dry.

To avoid the influence of dust and/or moisture in air, please keep the surface of

device clean and dry.

Electrostatic Prevention.

Operate in an electrostatic discharge protective area environment to avoid damages

induced by static discharges. Always ground both the internal and external

conductors of the cable to release static before connecting.

Handling Safety

Please handle with care during transportation to avoid damages to buttons, knob

interfaces and other parts on the panels.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

Safety Terms and Symbols

Terms in this Manual. The following terms may appear in this manual:

WARNING

Warning statements indicate the conditions or practices that could result in

injuries or loss of life.

CAUTION

Caution statements indicate the conditions or practices that could result in

damage to this product or loss of data.

Terms on the Product. The following terms may appear on the product:

DANGER

indicates an injury or hazard may immediately happen.

WARNING

indicates an injury or hazard may be accessible potentially.

CAUTION

indicates a potential damage to the instrument or other property might

occur.

Symbols on the Product. The following symbols may appear on the product:

Hazardous

Voltage

Please Refer to

Manuals

Protective

Earth

Terminal

Chassis

Ground

Test

Ground

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

Measurement Category

DS2000 series digital oscilloscopes can make measurements in Measurement

Category I.

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Measurement Category Definitions

Measurement category I is for measurements performed on circuits not directly

connected to MAINS. Examples are measurements on circuits not derived from

MAINS, and specially protected (internal) MAINS derived circuits. In the latter case,

transient stresses are variable; for that reason, the transient withstand capability of

the equipment is made known to the user.

Measurement category II is for measurements performed on circuits directly

connected to the low voltage installation. Examples are measurements on household

appliances, portable tools and similar equipment.

Measurement category III is for measurements performed in the building installation.

Examples are measurements on distribution boards, circuit-breakers, wiring,

including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed

installation, and equipment for industrial use and some other equipment, for

example. Stationary motors with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of the

low-voltage installation. Examples are electricity meters and measurements on

primary overcurrent protection devices and ripple control units.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

Ventilation Requirement

This oscilloscope uses fan to force cooling. Please make sure that the air intake and

exhaust areas are free from obstructions and have free air. When using the

oscilloscope in a bench-top or rack setting, provide at least 10 cm clearance beside,

above and behind the instrument for adequate ventilation.

WARNING

Inadequate ventilation may cause temperature increase which would

damage the instrument. So please keep the instrument well ventilated

during operation and inspect the intake and fan regularly.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

VII

Working Environment

Temperature

Operating: 0℃to +50℃

Non-operating: -20℃to +70℃

Humidity

Under +35℃: ≤90％relative humidity

+35℃to +40℃: ≤60％relative humidity

WARNING

To avoid short circuit inside the instrument or electric shock, please do not

operate in humid environment.

Altitude

Operating: less than 3 km

Non-operating: less than 15 km

Installation (overvoltage) Category

This product is powered by MAINS conforming to installation (overvoltage) category

II.

WARNING

Make sure that no overvoltage (such as that caused by thunderbolt) can

reach the product, or else the operator might expose to danger of electric

shock.

Installation (overvoltage) Category Definitions

Installation (overvoltage) category I refers to signal level which is applicable to

equipment measurement terminals connected to the source circuit. In these

terminals, precautions are done to limit the transient voltage to the corresponding

low level.

Installation (overvoltage) category II refers to the local power distribution level

which is applicable to equipment connected to the AC line (AC power).

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

VIII

Pollution Degree

Degree 2

Pollution Degree Definitions

Pollution degree 1: No pollution or only dry, non-conductive pollution occurs. The

pollution has no influence. For example: a clean room or air-conditioned office

environment.

Pollution degree 2: Normally only dry, non-conductive pollution occurs. Occasionally

a temporary conductivity caused by condensation may occur. For example: general

indoor environment.

Pollution degree 3: Conductive pollution occurs, or dry, non-conductive pollution

occurs which becomes conductive due to condensation which is expected. For

example: Sheltered outdoor environment.

Pollution degree 4: Pollution that generates persistent conductivity through

conductive dust, rain, or snow. For example: outdoor locations.

Safety Class

Class 1 –Grounded Product

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

RIGOL

DS2000 Quick Guide

General Care and Cleaning

General Care:

Do not store or leave the instrument in where the instrument will be exposed to

direct sunlight for long periods of time.

Cleaning:

Clean the instrument regularly according to its operating conditions. To clean the

exterior surface, perform the following steps:

1. Disconnect the instrument from all power sources.

2. Clean the loose dust on the outside of the instrument with a lint- free cloth (with

a mild detergent or water). When cleaning the LCD, take care to avoid scarifying

it.

CAUTION

To avoid damages to the instrument, do not expose them to liquids which

have causticity.

WARNING

To avoid injury resulting from short circuit, make sure the instrument is

completely dry before reconnecting to a power source.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Otros manuales para DS2000 Series

Tabla de contenidos

Otros manuales de Equipo de prueba de Rigol

Rigol

Rigol DS1000Z Series Manual de usuario

Rigol

Rigol DS4000 Series Manual de usuario

Rigol

Rigol MSO4000 Series Manual de usuario

Rigol

Rigol DS1000 Series Manual de usuario

Rigol

Rigol SA5000 Series Instrucciones de funcionamiento

Rigol

Rigol HDO4000 Series Manual de usuario

Rigol

Rigol HDO4000 Series Manual de usuario

Rigol

Rigol DS1000Z-E Series Manual de instalación y operación

Rigol

Rigol DG2052 Manual de usuario

Rigol

Rigol DS1000 Series Instrucciones de funcionamiento

Rigol

Rigol MSO8064 Manual de usuario

Rigol

Rigol MSO2000A Series Instrucciones de funcionamiento

Rigol

Rigol RPL2316 Manual de usuario

Rigol

Rigol DG2000 Series Manual de instalación y operación

Rigol

Rigol DS8000-R Series Manual de usuario

Rigol

Rigol DS1000E series Manual de usuario

Rigol

Rigol HDO1000 Series Manual de usuario

Rigol

Rigol MSO2000A Series Manual de usuario

Rigol

Rigol DSO-5200A Manual de usuario

Rigol

Rigol DS1000CA series Instrucciones de funcionamiento

Rigol

Rigol DS1074B Manual de usuario

Rigol

Rigol DS1000CA series Manual de usuario

Rigol

Rigol MSO1000Z series Instrucciones de funcionamiento

Rigol

Rigol DHO900 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario